Advertisement
i!tt /
Problem
1J1J,1&1,,
Model doesn't move
:J :, ... CJ-J�1J,;11J,f&I,\
Loss of Control
� -:, T �j!61&1,,
Doesn't Run Straight
.Lt� 61&1,\
Doesn't Stop
1t;tl u1&1,,
Doesn't reverse
A t:°- t:1J,t:1:11&1,\
Running Too Slowly
S1J,Jt•;, ?T .f>o
Car moves in reverse.
� - , - . i�- � J � � □ - 7 -
t,,,t-/(- t:- �f i
_ ,
-- H I U I
;::;-n,, 1 1cau IQ
TROU BLE SHOOTING
I
Jail /
Cause
, x i§i
�
'Y
'
Transmitter or receiver power not switched on.
:i'Efiffl�iili1l::1t� c! ti, Z 1, \ t ci: 1, \
Battery on model is not charged .
�1��ZJ' 6 :J ,+ ? 5 - i:Jf;,,f.tl, ""( \,\ � o
Connector has detached from receiver.
��Hc:: J: IJ t - r- ::t
□
T ? r- ��§i:Jf1i!J 1, \ n \ �
Due to high temperature the heat protection
system may be operating.
1 ,-1 y =f- ' 1 y / f <! h z 1,\ t J: \,\
Binding is not complete.
:i'EfifflffliiliW�]li:Jf�t ci: \, \
o
Batteries have run down.
1': � t J:��t->�!Mfili: < tc:: c!5 �
Main road or large steel pylon is nearby.
A T Y 1 ) y /_j ' r- 1 ) b W��i:J{tt U ( f J: \, \
Steering Trim is not adjusted correctly.
71\-1 - J l, 1:: ' ; z i:J{lg) � A., � ' \, \ �
Wheel screw (s) are loose.
'Y r- Jl, 1-- 1 ) b W ID;llmi:J{tt G < t .,i: \, \
;z
□
Throttle Trim is not adjusted correctly.
; z t:"- i-: :J Y 1-- D - -5 - WIDi\lmi:Jftt G < t .,i: \, \
Speed controller is not setup properly.
'Y r- Jl, 1-- 1 ) b WIDi\lmi:J{tt G < t .,i: \, \
; z
□
Throttle Trim is not adjusted correctly.
; z t:"- i-: :J Y 1-- D - -5 - WIDi\l�i:Jftt G < t .,i: \, \
Speed controller is not setup properly.
:i'Efiffl ffliiliW�]li:Jf�d J: \,\
o
Batteries have run down.
jli(J}JJ'.l ' B,J" (C:: :::1' � t-'71\ :J 1 ) i:Jf(;:J:: c! a'; ? L \, \ �
Dirt etc. has entered the drive train.
'E - /y - i:Jf�{t; G Z � -C \,\ �
Motor has lost power.
z1��W I ) } \- A A -1 o/ 7 7cf'. Jit
Check the reverse switch on transmitter.
@lfili'B� (c:: :::1' � t->lt':!>t ci: c ' i:Jf-:> a; ? Z 1, \ �
Dirt or sand is jamming a rotating part.
I
m�:.i.: 1 2
?
d- o
�
Switch power on as per Instruction Manual P. 1 2.
I
7E�HWE�
o
�
Refer charger instructions and charge correctly.
I
� a; � ' ln i:J' IJ c � G i6'1:3
�
Insert connectors all the way in.
I
;z -{ 'Y 7'- 7.f: OFF(c:: G , 'E - 5 -, ESCi:J%clt> � a; � ' �'?
o
�
Turn the power off and let the circuitry cool off.
I
■
EBJl
o
�
Referring to the manual page 1 1 .
I
7EfflHWE�
�
Refer charger instructions and charge correctly.
I
:i'Efi�p.fi ;/f: JVt. �
o
�
Run model in different area.
I
■
E�
0
�
Make adjustment as per Instruction Manual P. 1 5.
I
7\firal I.., Y :f- � ' 71\ -1 -J l, t:';z 7cf: G ? i:J' IJ ;melt> �
o
�
Tighten wheel screws with hex wrench .
I
■
E�
o
�
Make adjustment as per Instruction Manual P. 1 6.
I
■
E�
o
�
Make adjustment as per Instruction Manual P . 1 6, 1 7, 1 8, 1 9.
I
■
E�
o
�
Make adjustment as per Instruction Manual P. 1 6.
I
■
E�
o
�
Make adjustment as per Instruction Manual P . 1 6, 1 7, 1 8, 1 9.
I
7EfflHWE�
�
Refer charger instructions and charge correctly.
I
mJJJf!B�;/f: X Y T T Y ;z 9 �
0
�
Carry out maintenance on moving parts.
I
'E - /y - 7,f: ��9 �
o
�
Replace motor.
I
■
9 �
1 6�- V';/f:�� (c:: � 'Y 1-- 9 �
o
�
Refer to page 1 6 and set accordingly.
mJJJ*�;z b - � � @l&9 � � c 7cf: lit
o
�
Check so that the drive system rotates smoothly.
�- I
To Solve
?
'Y
,x - ::,, '-
■
� � ? Z tt G < 7E� 9 �
o
l l � - Y';(f:�� (U '\-{ Y " ' 9 �
■
� � ? Z tt G ( 7Effl 9 �
o
l 5�- V'tc::� ? Z tt G < ��9 �
l 6�- V'tc:: � ? Z tt G < �m9 �
l 6, 1 7, 1 8, 1 9�- Y'(c::� ? Z tt G < IDi\lm9 �
l 6�- �/(c:: � ? Z tt G < �m9 � o
l 6, 1 7, 1 8, 1 9�- Y'(c::� ? Z tt G < IDi\1�9 �
■
� � ? Z tt G ( 7Effl 9 �
o
o
o
0
o
o
o
o
o
o
o
o
o
o
■
9 �
o
35
Advertisement
