Table of Contents
Advertisement
Quick Links
FA NM A ST E R
cooling heating ventilation extraction
INSTRUCTION MANUAL
INDUSTRIAL DIESEL FAN HEATER (INDIRECT-FIRED)
MODEL: IDH2-20IN
FOR INDUSTRIAL USE ONLY
ADEQUATE VENTILATION REQUIRED
TO PREVENT SERIOUS INJURY, READ & UNDERSTAND ALL WARNINGS &
INSTRUCTIONS BEFORE USE. PLEASE KEEP THIS DOCUMENT FOR YOUR RECORDS
Advertisement
Table of Contents
Related Manuals for Fanmaster IDH2-20IN
Summary of Contents for Fanmaster IDH2-20IN
- Page 1 FA NM A ST E R cooling heating ventilation extraction INSTRUCTION MANUAL INDUSTRIAL DIESEL FAN HEATER (INDIRECT-FIRED) MODEL: IDH2-20IN FOR INDUSTRIAL USE ONLY ADEQUATE VENTILATION REQUIRED TO PREVENT SERIOUS INJURY, READ & UNDERSTAND ALL WARNINGS & INSTRUCTIONS BEFORE USE. PLEASE KEEP THIS DOCUMENT FOR YOUR RECORDS...
-
Page 2: For Your Information
FOR YOUR INFORMATION Thank you for purchasing a Fanmaster diesel heater. Please read this instruction manual carefully before using this heater. Disclaimer: Fanmaster reserves the right to make alterations to specifications, quantities, dimensions, for production or other reasons, subsequent to publication. - Page 3 ALWAYS CHECK THE POWER CABLE BEFORE USING THE APPLIANCE. IT MUST NOT BE BENT, TAUT, STRETCHED, CRUSHED OR ANY WAY DAMAGED. • IF THE POWER CORD AND/OR PLUG IS DAMAGED, IT MUST BE REPLACED BY FANMASTER, A SERVICE AGENT OR A QUALIFIED PERSONS. •...
-
Page 4: Product Description And Specifications
2. PRODUCT DESCRIPTION & SPECIFICATIONS PRODUCT DESCRIPTION Industrial diesel or kerosene indirect fired portable space/fan heater with closed combustion chamber. SPECIFICATIONS MODEL IDH2-20IN 20KW Heat Output* 68,240 BTU Air Flow (L/s) Fuel Type Diesel or Kerosene Fuel Consumption (L/h) Fuel Nozzle Size (gph) 0.60... -
Page 5: Assembling Instructions
3. ASSEMBLING INSTRUCTIONS Remove the heater from the carton. If the heater is damaged, please contact Fanmaster or where you purchased the heater from. Pos. Description Power Cord Frame Feet Pipe Assembly Plain Washer M5 8 or 12 Nut M5... - Page 6 3. ASSEMBLING INSTRUCTIONS - CONTINUED 1. Insert the wheel shaft “I” to the corresponding holes of the feet pipe assembly “B”. 2. Insert the cotter pin “H” to the corresponding holes; slide the wheels “G” over the wheel shaft “I”, put plain washer “F” to the two sides of the shaft, screw nut “E”...
- Page 7 4. OPERATING INSTRUCTIONS • Position the heater on a flat, level, non-flammable & solid surface. • Indirect-fired heaters while used in indoors, must be connected to an exhaust pipe to vent the fumes of combustion outside. To maintain an adequate Oxygen rate, a minimum of 80 m3/h airflow from outside must occur.
- Page 8 4. OPERATING INSTRUCTIONS - CONTINUED FLUE/EXHAUST INSTALLATION For indirect-fired heaters: connect the heater to an exhaust duct. To get a proper exhaust flow out, the fumes must rise throigh the flue. Avoid any elbows and bends in the first part of the exhaust ducts for at least 3m.
- Page 9 4. OPERATING INSTRUCTIONS - CONTINUED START-UP • Fill the tank with clean fuel. Only use Diesel or Kerosene • The fuel gauge on top of the tank allows you to check the fuel level • Connect the plug to the relevant power source •...
-
Page 10: Cleaning, Maintenance And Storage
5. CLEANING, MAINTENANCE & STORAGE • Before starting any maintenance task, shut down, unplug and let the heater cool down for at least 15 minutes. • Do not attempt any electrical repair yourself. If the heater needs service or repair, contact a qualified persons. - Page 11 (the air vent hole in the adjusting screw middle) clockwise to increase, anticlockwise to decrease the pressure: Model Air Pressure (bar) IDH2-20IN 0.38 Fig 4. Ignition Electrodes (qualified perons only) Clean, adjust, & if necessary replace ignition electrode. For electrode gaps see Fig.4- 5 (dimensions in mm) Fig 5.
-
Page 12: Wiring Diagram
6. WIRING DIAGRAM... -
Page 13: Parts Breakdown
7. PARTS BREAKDOWN... -
Page 14: Troubleshooting
8. TROUBLESHOOTING PROBLEM CAUSE SOLUTION Check power supply & voltage No power or low voltage Check fuse & replace if necessary Motor does not start Faulty or damaged power Check & replace cord The power indicator is Faulty motor/capacitor Check & if necessary replace flashing Detect the cause of overheating. -
Page 15: Warranty
To make a claim under the warranty, take the product (with proof of purchase) to the store where you purchased the product or go to https://www.fanmaster.com.au/warranty-claims-returns. This warranty is given by Fanmaster Pty Ltd ABN: 45 353 934 457 Unit 1/6-8 Yalgar Rd, KIRRAWEE NSW 2232 P: 1300 900 345 E: warranties@fanmaster.com.au... - Page 16 FA NM A ST E R cooling heating ventilation extraction Fanmaster Pty Ltd | 1/6-8 Yalgar Road, KIRRAWEE NSW 2232 1300 900 345 | sales@fanmaster.com.au | www.fanmaster.com.au N11664 MADE IN CHINA...