Table of Contents
Advertisement
Quick Links
FA NM A ST E R
cooling heating ventilation extraction
INSTRUCTION MANUAL
INDUSTRIAL DIESEL RADIANT HEATER
MODEL: HDR20
FOR INDUSTRIAL USE ONLY
ADEQUATE VENTILATION REQUIRED
TO PREVENT SERIOUS INJURY, READ & UNDERSTAND ALL WARNINGS &
INSTRUCTIONS BEFORE USE. PLEASE KEEP THIS DOCUMENT FOR YOUR RECORDS
Advertisement
Table of Contents
Related Manuals for Fanmaster HDR20
Summary of Contents for Fanmaster HDR20
- Page 1 FA NM A ST E R cooling heating ventilation extraction INSTRUCTION MANUAL INDUSTRIAL DIESEL RADIANT HEATER MODEL: HDR20 FOR INDUSTRIAL USE ONLY ADEQUATE VENTILATION REQUIRED TO PREVENT SERIOUS INJURY, READ & UNDERSTAND ALL WARNINGS & INSTRUCTIONS BEFORE USE. PLEASE KEEP THIS DOCUMENT FOR YOUR RECORDS...
-
Page 2: For Your Information
FOR YOUR INFORMATION Thank you for purchasing a Fanmaster diesel heater. Please read this instruction manual carefully before using this heater. Disclaimer: Fanmaster reserves the right to make alterations to specifications, quantities, dimensions, for production or other reasons, subsequent to publication. - Page 3 ALWAYS CHECK THE POWER CABLE BEFORE USING THE APPLIANCE. IT MUST NOT BE BENT, TAUT, STRETCHED, CRUSHED OR ANY WAY DAMAGED. • IF THE POWER CORD AND/OR PLUG IS DAMAGED, IT MUST BE REPLACED BY FANMASTER, A SERVICE AGENT OR A QUALIFIED PERSONS. •...
-
Page 4: Product Description And Specifications
2. PRODUCT DESCRIPTION & SPECIFICATIONS PRODUCT DESCRIPTION Industrial diesel or kerosene portable radiant heater with open combustion chamber. SPECIFICATIONS MODEL HDR20 20KW Heat Output* 68,240 BTU Air Flow (L/s) Fuel Type Diesel or Kerosene Fuel Consumption (L/h) Fuel Nozzle Size (gph) -
Page 5: Assembling Instructions
3. ASSEMBLING INSTRUCTIONS Remove the heater from the carton. If the heater is damaged, please contact Fanmaster or where you purchased the heater from. 1. Remove the 2 screws from the front fixed ring 2. Place the protection panel on the bottom 3. - Page 6 4. OPERATING INSTRUCTIONS • Position the heater on a flat, level, non-flammable & solid surface. • Only position the heater in the normal upright position (on the wheels) • Do not place the heater near walls, corners or low ceilings. •...
-
Page 7: Cleaning, Maintenance And Storage
5. CLEANING, MAINTENANCE & STORAGE • Before starting any maintenance task, shut down, unplug and let the heater cool down for at least 15 minutes. • Do not attempt any electrical repair yourself. If the heater needs service or repair, contact a qualified persons. -
Page 8: Wiring Diagram
6. WIRING DIAGRAM... -
Page 9: Parts Breakdown
7. PARTS BREAKDOWN... -
Page 10: Troubleshooting
Fuel Filter is dirty or blocked Clean fuel filter with clean fuel Ignition error Contact Fanmaster Damaged cable Replace or contact Fanmaster Sensor is damaged Replace or contact Fanmaster Turn the heater off & wait until Internals overheating the heater has cooled down... - Page 11 8. TROUBLESHOOTING - CONTINUED PROBLEM CAUSE SOLUTION The switch is in the “O” OFF Turn the switch to “I” ON postion Check the plug is properly connected to the power No power source. Check the power Heater does not supply Adjust the thermostat higher Thermostat setting than the ambient temperature...
-
Page 12: Warranty
To make a claim under the warranty, take the product (with proof of purchase) to the store where you purchased the product or go to https://www.fanmaster.com.au/warranty-claims-returns. This warranty is given by Fanmaster Pty Ltd ABN: 45 353 934 457 Unit 1/6-8 Yalgar Rd, KIRRAWEE NSW 2232 P: 1300 900 345 E: warranties@fanmaster.com.au... - Page 16 FA NM A ST E R cooling heating ventilation extraction Fanmaster Pty Ltd | 1/6-8 Yalgar Road, KIRRAWEE NSW 2232 1300 900 345 | sales@fanmaster.com.au | www.fanmaster.com.au N11664 MADE IN CHINA...