Table of Contents
Advertisement
Position the drive rollers so that they are at approximately the
same height as the wheel hub (middle of wheel ± 30 mm).
Driving direction
Truma can supply a spacer plate set for compensating for
height differences of up to 45 mm (Part no. 60010-66000,
2 pcs. à 15 mm). Up to three spacer plates can be used at
each side. A bolt set (Part no. 60010-70000) is needed to
attach the spacer plates.
The flat frame mounting set (Part. no. 60010-64900) must be
used for height differences of more than 45 mm. Check that
there is adequate ground clearance (min. 110 mm).
The correct distance can be set between the tyre and the roller
(20 mm) with the provided spacer by sliding the (swivelled out)
drive units in the longitudinal direction. The movable middle
tube makes it possible to adapt to the width of the frame.
Driving direction
Slide drive units in lateral direction so that the maximum
amount of tyre tread is covered.
After correctly positioning the bolts and nuts of the mounting
set, tighten slightly and then check the required distances/
clearances again. The weight of the caravan must be on the
wheels when doing this.
Move sliding middle tube to a central position (e.g. measure
at open side of middle tube with a pocket rule), tighten the
4 bolts (15 – 20 Nm) and secure the locknuts.
20 Nm
40 Nm
40 Nm
Re-check that all 6 bolts have been tightened to the
correct torque!
min. 110 mm
20 mm
min. 110 mm
Ensure that there is adequate
clearance between the gearbox
and the tyre/shock absorber so
that they do not touch.
The minimum clearance
with the drive units
swivelled in is 10 mm.
Re-check the distance of 20 mm
to the tyre (with weight on
wheels) and then tighten the
2 mounting set bolts (M 8) with
20 Nm and the 4 mounting set
bolts (M 10) with 40 Nm.
The bolt tightening order must
be strictly adhered to for correct
installation.
Fit covering plates:
Place covering plate onto housing and fix in position with
3 guide pins in each case (knock in with a hammer or screw-
driver handle).
± 30 mm
Installation of motor cables and control unit
The Mover is only suitable for connection to 12 V batteries
(DC voltage).
Remove battery cable terminals and disconnect any
external electrical power before starting work. If you are
unsure about the electrical installation, have it checked out by
a qualified Auto Electrician.
Two high-power cables for the drive motor (6 mm²) and a two-
wire cable for the swivel-in motor are pre-attached to each
motor. Mark the respective motor connecting cables (motor
A or B – see also wiring diagram) and temporarily route to the
intended control unit installation position on the underbody of
the caravan. An example of a suitable location for the control
unit is in a bed stowage box in close proximity to the manoeu-
vring system, at least 40 cm away from the battery.
Insert control unit into stowage box and secure with the sup-
plied chipboard screws (5 x 16).
Drill a 25 Ø hole on the floor of the caravan for leading the
cables through, approx. 150 mm from the control unit terminal
strip.
Take care to avoid any chassis members, gas pipes and
electrical wires!
Drill hole and lead cables through floor of caravan to control
unit in such a way that they cannot chafe (particularly when
leading through metal panels). This can be done using protec-
tive tubes, which will prevent the cables from being damaged.
The drive motors move during operation. To compen-
sate for this, the cables should be secured loosely with
a little play in this area in order to prevent cable stretching. No
cables must be routed over the control unit!
Secure cables to chassis and/or underbody using the supplied
clips and screws.
Seal hole in vehicle underbody using plastic body sealant.
Installing the position
indicator:
Push the position indicator
into the two holes in the
gearbox.
9
Hide quick links:
Advertisement
Table of Contents
