Siemens RUGGEDCOM RS8000H Installation Manual
Rugged ethernet switches
Hide thumbs
Also See for RUGGEDCOM RS8000H:
- Installation manual (32 pages) ,
- Installation manual (40 pages)
Related Manuals for Siemens RUGGEDCOM RS8000H
Summary of Contents for Siemens RUGGEDCOM RS8000H
- Page 1 Edition 12/2021 Installation Manual SIMATIC NET Rugged Ethernet Switches RUGGEDCOM RS8000H https://www.siemens.com/ruggedcom...
- Page 2 Preface Introduction Installing the Device SIMATIC NET Device Management Rugged Ethernet Switches RUGGEDCOM RS8000H Communication Ports Technical Specifications Installation Manual Certification 12/2021 C79000-G8976-1022-06...
- Page 3 Note the following: WARNING Siemens products may only be used for the applications described in the catalog and in the relevant technical documentation. If products and components from other manufacturers are used, these must be recommended or approved by Siemens. Proper transport, storage, installation, assembly, commissioning, operation and maintenance are required to ensure that the products operate safely and without any problems.
-
Page 4: Table Of Contents
Accessing Documentation ....................... v Registered Trademarks ......................v Warranty ..........................vi Training ..........................vi Customer Support ........................vi Contacting Siemens ....................... vii Introduction ........................... 1 Feature Highlights ....................1 Description ......................2 Required Tools and Materials ................. 4 Decommissioning and Disposal ................4 Cabling Recommendations .................. - Page 5 Certification ......................... 25 Approvals ......................25 6.1.1 CSA ........................25 6.1.2 European Union (EU) ..................25 6.1.3 FCC ........................26 6.1.4 ISO ........................26 6.1.5 RoHS ........................27 EMC and Environmental Type Tests ..............27 RUGGEDCOM RS8000H Installation Manual, 12/2021, C79000-G8976-1022-06...
-
Page 6: Preface
SIMATIC NET Glossary The SIMATIC NET Glossary describes special terms that may be used in this document. The glossary is available online via Siemens Industry Online Support (SIOS) at: https://support.industry.siemens.com/cs/ww/en/view/50305045 Accessing Documentation The latest user documentation for RUGGEDCOM RS8000H is available online at https://support.industry.siemens.com. -
Page 7: Warranty
Preface Warranty Warranty Siemens warrants this product for a period of five (5) years from the date of purchase, conditional upon the return to factory for maintenance during the warranty term. This product contains no user-serviceable parts. Attempted service by unauthorized personnel shall render all warranties null and void. -
Page 8: Contacting Siemens
Call a local hotline center to submit a Support Request (SR). To locate a local hotline center, visit https://w3.siemens.com/aspa_app/?lang=en. Mobile App Install the Industry Online Support app by Siemens AG on any Android, Apple iOS or Windows mobile device and be able to: •... - Page 9 Preface Contacting Siemens viii RUGGEDCOM RS8000H Installation Manual, 12/2021, C79000-G8976-1022-06...
-
Page 10: Introduction
The RUGGEDCOM RS8000H model provides IEEE 1613 Class 2 error-free communications performance under EMI stress. An operating temperature range of -40 to 85 °C (-40 to 185 °F) allows the RUGGEDCOM RS8000H to be placed in almost any location. The RUGGEDCOM RS8000H provides a wide range of power supply options suitable for multiple industries and for worldwide operability. -
Page 11: Description
Terminal blocks for reliable maintenance free connections • CSA/UL 60950 safety approved to 85 °C (185 °F) Description The RUGGEDCOM RS8000H features various ports, controls and indicator LEDs on the front and rear panels for configuring and troubleshooting the device. RUGGEDCOM RS8000H Installation Manual, 12/2021, C79000-G8976-1022-06... - Page 12 Port Status Indicator LEDs These LEDs indicate when serial ports are active. State Meaning Link Solid Link detected No link detected Blinking Link activity (receiving) No link activity Blinking Link activity (transmitting) No link activity RUGGEDCOM RS8000H Installation Manual, 12/2021, C79000-G8976-1022-06...
-
Page 13: Required Tools And Materials
RUGGEDCOM RS8000H, refer to "Communication Ports (Page 19)". Required Tools and Materials The following tools and materials are required to install the RUGGEDCOM RS8000H: Tools/Materials Purpose AC or DC power cord (16 AWG) For connecting power to the device. -
Page 14: Supported Fiber Optic Cables
Siemens also does not recommend using copper Ethernet ports to interface with devices in the field across distances that could produce high levels of ground potential rise (i.e. greater than 2500 V), during line-to-ground fault conditions. - Page 15 Introduction 1.5.1 Supported Fiber Optic Cables RUGGEDCOM RS8000H Installation Manual, 12/2021, C79000-G8976-1022-06...
-
Page 16: Installing The Device
This product contains no user-serviceable parts. Attempted service by unauthorized personnel shall render all warranties null and void. Changes or modifications not expressly approved by Siemens Canada Ltd. could invalidate specifications, test results, and agency approvals, and void the user's authority to operate the equipment. -
Page 17: General Procedure
Configure the device. Mounting the Device The RUGGEDCOM RS8000H is designed for maximum mounting and display flexibility. It can be equipped with connectors that allow it to be installed in a 48 cm (19 in) rack, 35 mm (1.4 in) DIN rail, or directly on a panel. -
Page 18: Mounting The Device On A Din Rail
2.2.1 Mounting the Device on a DIN Rail The RUGGEDCOM RS8000H can be ordered with a panel/DIN rail adapter preinstalled on the back of the chassis. Use the adapter to mount the device to a standard 35 mm (1.4 in)IEC/EN 60715 or TS35 DIN rail. -
Page 19: Mounting The Device To A Rack
Lift the device off the DIN rail. 2.2.2 Mounting the Device to a Rack To secure the device to a standard 48 cm (19 in) rack, do the following: Remove the four screws from the side of the device. RUGGEDCOM RS8000H Installation Manual, 12/2021, C79000-G8976-1022-06... - Page 20 Forced airflow is not required. However, any increase in airflow will result in a reduction of ambient temperature and improve the long-term reliability of all equipment mounted in the rack space. Secure the adapter to the rack using the supplied hardware. RUGGEDCOM RS8000H Installation Manual, 12/2021, C79000-G8976-1022-06...
-
Page 21: Mounting The Device To A Panel
NO contact and closes the NC (Normally Closed) contact. Note Control of the failsafe relay output is configurable through RUGGEDCOM ROS. One common application for this relay is to signal an alarm if a power failure occurs. For RUGGEDCOM RS8000H Installation Manual, 12/2021, C79000-G8976-1022-06... -
Page 22: Connecting Power
Normally Closed Common Normally Open Figure 2.5 Failsafe Alarm Relay Wiring Connecting Power The RUGGEDCOM RS8000H supports a single integrated high AC/DC or low DC power supply IMPORTANT • For 88-300 VDC rated equipment, an appropriately rated circuit breaker must be installed. -
Page 23: Connecting Ac Power
Using a braided wire or other appropriate grounding wire, connect the surge ground terminal to the chassis ground connection. The surge ground terminal is used as the ground conductor for all surge and transient suppression circuitry internal to the unit. RUGGEDCOM RS8000H Installation Manual, 12/2021, C79000-G8976-1022-06... -
Page 24: Connecting Dc Power
This cable connects transient suppression circuitry to chassis ground and must be removed in order to avoid damage to transient suppression circuitry during testing. RUGGEDCOM RS8000H Installation Manual, 12/2021, C79000-G8976-1022-06... - Page 25 Using a #6 ring tongue and #6-32 screw, secure the ground terminal on the power source to the chassis ground terminal on the device. Make sure the lug is tightened to 1.7 N·m (15 lbf·in). Stainless Steel Stud #6-32 Screw #6 Ring Tongue Figure 2.9 Chassis Ground Connection RUGGEDCOM RS8000H Installation Manual, 12/2021, C79000-G8976-1022-06...
-
Page 26: Device Management
Communication Ports Connect any of the available Ethernet ports on the device to a management switch and access the RUGGEDCOM RS8000H console and Web interfaces via the device's IP address. For more information about available ports, refer to "Communication Ports (Page 19)". -
Page 27: Configuring The Device
Configuration Manual" associated with the installed software release. Resetting the Device The RUGGEDCOM RS8000H can be reset (rebooted) using the RESET button. The RESET button is recessed and can only be reached using a pin or small screwdriver. To reset the device, quickly press and release the RESET button with a pin. -
Page 28: Communication Ports
ROS. For more information on how to access the factory data file, refer to the "RUGGEDCOM RS8000H Configuration Manual" for the RUGGEDCOM RS8000H. Each communication port type has a specific place in the RUGGEDCOM RS8000H chassis. Ports 1 to 4 Ports 5 to 8 Figure 4.1... -
Page 29: Fiber Optic Ethernet Ports
Tx Connector Tx Connector Rx Connector Rx Connector Figure 4.3 SC Port Figure 4.4 ST Port For specifications on the available fiber optic Ethernet ports, refer to "Fiber Optic Ethernet Port Specifications (Page 22)". RUGGEDCOM RS8000H Installation Manual, 12/2021, C79000-G8976-1022-06... -
Page 30: Technical Specifications
Current 30 VAC 0.3 A 30 VDC 80 VDC 0.3 A Copper Ethernet Port Specifications The following details the specifications for copper Ethernet ports that can be ordered with the RUGGEDCOM RS8000H. Speed 10/100Base-TX Connector RJ45 Duplex FDX/HDX RUGGEDCOM RS8000H... -
Page 31: Fiber Optic Ethernet Port Specifications
The following details the specifications for fiber optic Ethernet ports that can be ordered with the RUGGEDCOM RS8000H. Operating Environment The RUGGEDCOM RS8000H is rated to operate under the following environmental conditions. Ambient Operating -40 to 85°C (-40 to 185 °F) - Page 32 Technical Specifications 5.7 Dimension Drawings 248.9 Figure 5.1 Overall Dimensions 479.4 464.5 Figure 5.2 Rack Mount Dimensions RUGGEDCOM RS8000H Installation Manual, 12/2021, C79000-G8976-1022-06...
- Page 33 Technical Specifications 5.7 Dimension Drawings 274.3 264.2 Figure 5.3 Panel and Din Rail Mount Dimensions RUGGEDCOM RS8000H Installation Manual, 12/2021, C79000-G8976-1022-06...
-
Page 34: Certification
Certification The RUGGEDCOM RS8000H device has been thoroughly tested to guarantee its conformance with recognized standards and has received approval from recognized regulatory agencies. Approvals This section details the standards to which the RUGGEDCOM RS8000H complies. 6.1.1 This device is certified by the CSA Group to meet the requirements of the following standards: •... -
Page 35: Fcc
The device is marked with the CE symbol and can be used throughout the European community. A copy of the CE Declaration of Conformity is available from Siemens Canada Ltd.. For contact information, refer to "Contacting Siemens (Page vii)". -
Page 36: Rohs
Certification 6.1.5 RoHS 6.1.5 RoHS This device is declared by Siemens Canada Ltd. to meet the requirements of the following RoHS (Restriction of Hazardous Substances) directives for the restricted use of certain hazardous substances in electrical and electronic equipment: • China RoHS 2... - Page 37 Test Levels Clause C37.90.3 Enclosure Contact ±8 kV Enclosure Air ±15 kV C37.90.2 Radiated RFI Enclosure ports 35 V/m C37.90.1 Fast Signal ports ±4 kV @ 2.5 kHz Transient DC Power ports ±4 kV RUGGEDCOM RS8000H Installation Manual, 12/2021, C79000-G8976-1022-06...
- Page 38 Test Db 95% (non- Heat, Cyclic) condensing), 55 °C (131 °F), 6 cycles IEC 60255-21-1 Vibration 2 g @ 10-150 Hz Class 2 IEC 60255-21-2 Shock 30 g @ 11 ms Class 2 RUGGEDCOM RS8000H Installation Manual, 12/2021, C79000-G8976-1022-06...
- Page 39 Certification 6.2 EMC and Environmental Type Tests RUGGEDCOM RS8000H Installation Manual, 12/2021, C79000-G8976-1022-06...
- Page 40 For more information Siemens RUGGEDCOM https://www.siemens.com/ruggedcom Industry Online Support (service and support) https://support.industry.siemens.com Industry Mall https://mall.industry.siemens.com Siemens Canada Ltd. Digital Industries Process Automation 300 Applewood Crescent Concord, Ontario, L4K 4E5 Canada © 2021 Siemens Canada Ltd. Subject to change...