Craftmade MRN52 Installation Manual

Hide thumbs

Table of Contents

Quick Links

Download this manual

Morrison

Installation Guide

For Model:

MRN52

E192641

net weight of fan: xx.xx lb (xx,1 kg)

READ THESE INSTRUCTIONS AND

SAVE THEM FOR FUTURE USE

Need help?

Do you have a question about the MRN52 and is the answer not in the manual?

Questions and answers

Summary of Contents for Craftmade MRN52

Page 1: Table Of Contents
READ THESE INSTRUCTIONS AND SAVE THEM FOR FUTURE USE Morrison Installation Guide For Model: MRN52 Table of Contents: Safety Tips. pg. 2 Unpacking Your Fan. pg. 3 Parts Inventory. pg. 3 Installation Preparation. pg. 4 Hanging Bracket Installation. pg. 4 Fan Assembly.
Page 2: Safety Tips
(2) this LED light kit must accept any interference received, including interference that may cause undesired operation. Distributed by: Craftmade, 650 S. Royal Lane, Coppell, TX, 75019; 1-800-486-4892 NOTE: The important safety precautions and instructions appearing in the manual are not meant to cover all possible conditions and situations that may occur.
Page 3: Unpacking Your Fan
1. Unpacking Your Fan. Carefully open the packaging. Remove items from Styrofoam inserts. Remove motor housing and place on carpet or Styrofoam to avoid damage to finish. *The motor stabilization pieces may be dicarded at this time. Do not discard fan carton or Styrofoam inserts should this fan need to be returned for repairs.
Page 4: Installation Preparation
3. Installation Preparation. blade edge To prevent personal injury and damage, ensure inches 7 feet that the hanging location allows the blades a (2.13 m) (76 cm) clearance of 7 feet (2.13m) from the floor and 30in. (76cm) from any wall or obstruction. This fan is suitable for room sizes up to 400 square 12ft.
Page 5: Fan Assembly. Pgs
set screw 5. Fan Assembly. stop pin Remove hanging ball from downrod provided by hanging ball loosening set screw on hanging ball. Lower hanging ball and remove stop pin and then slide hanging ball off of the downrod. [Refer to diagram 1.] diagram 1 Loosen yoke set screws and nuts at top of motor housing.
Page 6 5. Fan Assembly. (cont.) safety cable loop wood With the hanging bracket secured to the outlet ceiling box and able to support the fan, you are now joist ready to hang your fan. Grab the fan firmly wood screw with two hands. Slide downrod through and washer opening in hanging bracket and let hanging ball rest on the hanging bracket.
Page 7: Wiring
6. Wiring. ground (green WARNING: Turn off circuit breakers to current fixture or bare) white supply wire from breaker panel and be sure switch is turned to the OFF position. black supply wire ground (green CAUTION: Be sure outlet box is properly grounded and or bare) that a ground wire (GREEN or Bare) is present.
Page 8: Canopy Assembly
7. Canopy Assembly. Locate 2 screws on underside of hanging bracket and remove screw closest to the open antenna end of the hanging bracket. Partially loosen the other screw. Lift canopy to hanging bracket. hanging bracket Place rounded part of slotted hole in canopy receiver over loosened screw in hanging bracket and push up.
Page 9: Light Kit Assembly
9. Light Kit Assembly. Remove 1 screw from motor plate on underside of motor housing and partially loosen the other 2 screws. Align slotted holes in fitter plate with loosened screws in motor plate, allowing motor molex connectors to come through center housing hole in fitter plate.
Page 10: Handheld Remote Control Assembly
10. Handheld Remote Control Assembly. remote IN ORDER TO USE THE HANDHELD REMOTE CONTROL, control CONTINUE WITH SECTION 10 for remote control assembly instructions. If you have already installed the cover wall control but do not wish to use the handheld remote control, proceed to Section 11.
Page 11: Automated Learning Process./Activating Code
11. Automated Learning Process./Activating Code. CAUTION: The wall and/or handheld remote control can be programmed to multiple receivers or fans. If this is not desired, turn wall switch off to any other programmable receiver or fan. Restore electrical power and then, if using wall control, set slider switch on wall control to the ON position.
Page 12: Troubleshooting
Service at 1-800-486-4892 to arrange for return of fan. direction. Return fan, shipping prepaid, to Craftmade. We will repair 3. Check to be sure wall control (optional use) is wired or ship you a replacement fan, and we will pay the return properly.