Advertisement
Quick Links
Advertisement
Related Manuals for TSS 3x3 Power Rack with Belt Squat
Summary of Contents for TSS 3x3 Power Rack with Belt Squat
- Page 1 3x3 Power Rack with Belt Squat...
-
Page 2: Personal Safety
Read safety warnings, instructions illustrations provided for this piece of strength equipment. Failure to follow all instructions listed below may result in serious injury or death. User assumes all potential risks of assembly or use of this product. PERSONAL SAFETY ●... - Page 3 Required Tools ● Crescent Wrench ● 1 ⅛” and 9/16” Socket and Wrench ● 5/32 Allen Key Parts 3PRBS-001 (x1) Part A 3PRBS-003 (x1) Part C *3PR-100 (x1) Part MB* (Upgrade; Replaces Part A) 3PRBS-004 (x2) Part D 3PRBS-002 (x1) Part B 3PRBS-005 (x1)
- Page 4 3PRBS-010 (x1) Part J 3PRBS-006 (x1) Part F 3PRBS-011 (x1) Part K 3PRBS-007 (x2) Part G 3PRBS-008 (x1) Part H 3PRBS-012 | (x1) | Part L 3PRBS-009 (x1) Part I...
- Page 5 3PRBS-014 (x2) Part P 3PRBS-013 (x2) Part M 3PRBS-016 (x2) Part R 76 ½” Cable (x1) Part N 3PRBS-017 | (x2) | Part S 3PRBS-018 | (x2) | Part T 84 ½” Cable (x1) Part O...
- Page 6 ¾” Flat Washer (x16) Part X 3PRBS-015 (x2) Part Q ¾” Lock Washer (x20) Part AB 3PRBS-019 (x8) Part U ⅜” Flat Washer (x18) Part AC ⅜” Lock Nut (x20) Part AD Carabiner (x3) Part V ⅜” Wing Nut (x2) Part AE ¾”...
- Page 7 Rubber Stopper (x2) Part AF Spacer (x2) Part AG ⅜” x 4” Bolt | (x20) Part AA Set Screw Collar | (x2) | Part AI Pulley | (x1) Part AH...
- Page 8 Assembly Image 1 above displays the assembly of parts L, M, AF, and AI.
- Page 9 Part C will have part Q placed with it in the organization displayed in Image 3 above and part E will have part T placed In the Image 2 above the arrows with it in the same organization display where parts C, E and D as part C and Q.
- Page 10 In Image 4 above displays where all other ¾” hardware will be placed and the organization of the hardware can be seen in Image 5 below.
- Page 11 Using the parts that were assembled in image 1 place them into part E until the assembly is above part C and slide them into part C. Once the assembly has been properly placed, tighten part AI right below part E using a 5/32 allen key.
- Page 12 Parts G, H, Z, AE, AG, and AH will come pre-assembled in the manner displayed above. Parts H and AH can be placed in different locations as desired; above simply shows them placed in the center holes of part G.
- Page 13 Parts I and J will be placed on top of the power rack as seen in image 8 above. The assembly created in image 7 will be placed beneath the parts I and J as seen in image 8. Parts I, J, and the previous assembly will be attached with parts AA and AD.
- Page 14 Attach part N to part L with part V. With part V removed on the other end feed part N through the hole in part E and across part B as seen in image 9 above.
- Page 15 Image 10 above displays the organization of the ⅜” hardware which will be used for part U.
- Page 16 *Place P, R, and S in desired location*...
- Page 17 Place part F on top of part D. Attach part O to N with part V. Feed part O underneath part F ensuring that it lines up with the pulley underneath part F. *These parts can be removed and attached as desired.*...
- Page 18 To use the low cable system attach part O to N with V and feed it through part K as seen in image 13. *These parts can be removed and attached as desired.*...
- Page 19 You have now completed assembling your very own 3x3 Rack with Weight Storage and Belt Squat Attachment! Thank you for choosing Texas Strength Systems for your fitness needs. If you have any questions, comments, or concerns please don’t hesitate to contact our staff. Contact Information Email: wesz@texasstrengthsystems.com...
Need help?
Do you have a question about the 3x3 Power Rack with Belt Squat and is the answer not in the manual?
Questions and answers