TSS 3x3 Power Rack with Hi/Low Cable System Assembly Instructions Manual
Hide thumbs
Also See for 3x3 Power Rack with Hi/Low Cable System:
- Assembly instructions manual (8 pages)
Advertisement
Quick Links
Advertisement
Related Manuals for TSS 3x3 Power Rack with Hi/Low Cable System
Summary of Contents for TSS 3x3 Power Rack with Hi/Low Cable System
- Page 1 3x3 Power Rack with Hi/Low Cable System...
-
Page 2: Personal Safety
Read safety warnings, instructions illustrations provided for this piece of strength equipment. Failure to follow all instructions listed below may result in serious injury or death. User assumes all potential risks of assembly or use of this product. PERSONAL SAFETY ●... - Page 3 Required Tools ● Crescent Wrench ● 1 ⅛” and 9/16” Socket and Wrench ● 5/32 Allen Key Parts 3PRWSHL-003 (x1) Part C 3PRWSHL-001 (x1) Part A *3PR-100 (x1) Part MB* (Upgrade; Replaces Part A) 3PRWSHL-004 (x2) Part D 3PRWSHL-005 (x1) Part E 3PRWSHL-002 (x1)
- Page 4 3PRWSHL-007 (x1) Part G 3PRWSHL-010 (x2) Part J 3PRWSHL-008 (x1) Part H 76 ½” Cable (x1) Part K 3PRWSHL-009 | (x1) | Part I 84 ½” Cable (x1) Part L...
- Page 5 3PRWSHL-011 (x2) Part M 3PRWSHL-013 | (x2) | Part Q 3PRWSHL-012 (x2) Part N 3PRWSHL-014 | (x2) | Part R Carabiner (x3) Part S 3PRWSHL-015 (x2) Part O ¾” Nut (x20) Part T 3PRWSHL-016 (x8) Part P ¾” Flat Washer (x16) Part U...
- Page 6 ⅜” Lock Nut (x20) Part Z ¾” Lock Washer (x20) Part V ⅜” Flat Washer (x18) Part W ⅜” x 1.25” Bolt (x2) Part AA Rubber Stopper (x2) Part AB ¾ x 4.5” Bolt (x20) Part X Set Screw Collar | (x2) | Part AC ⅜”...
- Page 7 Assembly Image 1 above displays the assembly of parts J, I, AB, and AC.
- Page 8 Part C will have part O placed with it in the organization displayed in Image 3 above and part E will have part R placed with it in the same organization In the Image 2 above the arrows as part C and O. display where parts C, E and D will be attached with parts O and R respectively.
- Page 9 In Image 4 above displays where all other ¾” hardware will be placed and the organization of the hardware can be seen in Image 5.
- Page 10 Using the parts that were assembled in image 1 place them into part E until the assembly is above part C and slide them into part C. Once the assembly has been properly placed, tighten part AC right below part E using a 5/32 allen key.
- Page 11 Place part F on part E and G on part B as seen in image 7. Part F will be attached with part AA and Z as seen in image 8. Part G will be attached with part Y, W, and Z as seen in image 9.
- Page 12 Attach part K to part I with part S. With part S removed on the other end feed part K through the hole in part E and across part B as seen in image 10 above.
- Page 13 Attach part L to K with S and feed it through part H as seen in image 11.
- Page 14 Image 12 above displays the organization of the ⅜” hardware which will be used for part P.
- Page 15 *Place M, N, and Q in desired location*...
- Page 16 You have now completed assembling your very own 3x3 Rack with Weight Storage and Hi/Low Cable System! Thank you for choosing Texas Strength Systems for your fitness needs. If you have any questions, comments, or concerns please don’t hesitate to contact our staff. Contact Information Email: wesz@texasstrengthsystems.com...
Need help?
Do you have a question about the 3x3 Power Rack with Hi/Low Cable System and is the answer not in the manual?
Questions and answers