Related Manuals for Aquatic LuxeAir Series
Summary of Contents for Aquatic LuxeAir Series
- Page 1 Owner’s Manual & InstallatIOn GuIde Note: Read all instructions before proceeding with installation. All specifications are ± 1/4’’ and are subject to change without notice.
-
Page 2: Table Of Contents
Repair Information Water Quality Issues User Information FCC Information Serial Number - How to Locate TrOuBLEShOOTiNg guidE Symptoms/Possible Problems/Solutions PArTS OrdEr FOrm/PArTS mAPS/PArTS LiST Parts Order Form Parts Maps Parts List AquATiC LimiTEd wArrANTy TABLE OF CONTENTS aquatic Industries, Inc. -
Page 3: Product Registration Information
Your product warranty is registered and confirmed with Aquatic through the Serial Number on your unit. You do not need to contact Aquatic to confirm registration. Please fill out the information below and reference when contacting the distributor to expedite warranty claims. -
Page 4: Congratulations
CONgRATULATIONS! You have chosen one of the finest bath products in the world! Aquatic Industries supports your purchase with strong commitments to quality and customer satisfaction. Please read and follow all of the instructions contained in this Owner’s Manual before installing, operating or maintaining your whirlpool. -
Page 5: Safety Instructions
Each bather should start their bath with fresh water. CAuTiON: DO NOT use hArsh ABrAsIves Or sOLveNTs FOr cLeANINg ThIs uNIT. iNSTALLEr/OwNEr BEArS ALL rESPONSiBiLiTy TO COmPLy wiTh ALL STATE ANd LOCAL COdES whEN iNSTALLiNg ThiS PrOduCT. SAVE ThESE iNSTruCTiONS aquatic Industries, Inc. -
Page 6: Pre-Installation Procedures
6. with the pump running, turn on the blower. check all functions. 7. Inspect the tub completely. Any defect must be reported to Aquatic Industries, Inc. prior to installation in order to have it covered by warranty. should inspection indicate any damage, do not install the bath. -
Page 7: Structural Preparation
Ledge installation - 1 wall installation wArNiNg: ALL ELECTriCAL CONNECTiONS ShOuLd BE mAdE By A LOCALLy LiCENSEd ELECTriCiAN. aquatic Industries, Inc. Ledge installation - 2 Sunken installation NOTE: Due to the variety of... -
Page 8: Factory Installed Tile Flange
2. walls and floors meet fire safety requirements of local building code and/or FhA/huD Minimum Property standards. Before installation of the panel, fill the unit, test the whirlpool system for proper operation and check for leaks, then drain. 3. A mortar base is prepared (this is mandatory for proper installation). aquatic Industries, Inc. - Page 9 Before installation of the panel, fill the unit, test the whirlpool system for proper operation and check for leaks, then drain. Integrally Skirted Acrylic Whirlpool Left Side Edge aquatic Industries, Inc. Framing Dry wall Right Side Edge Clips...
-
Page 10: Rough-In Measurements
5 minutes. Check for leaks carefully both while pump is running and has been turned off. Allow water to stand in tub for at least 30 minutes before draining. AquATiC iNduSTriES, iNC. wiLL NOT BE rESPONSiBLE FOr wATEr dAmAgE OF ANy KiNd iN CONNECTiON wiTh ONE OF Our whirLPOOL BAThS. -
Page 11: Electrical Installation
“heater”. Plug the cord labeled “Main Ac Input” into the outlet labeled “Main” (see diagram on page 12). CAuTiON: Before use of the pump and heater, test the gFCi for proper operation. The pump and heater should turn off when the gFCi “Test” button is pushed. aquatic Industries, Inc. -
Page 12: Electrical Wiring Schematics
BONdiNg wirE: Connect a #8 bare copper bonding wire from the pump motor to the heater and then to the cold water plumbing or other suitable ground. grounding is required. grounding is NOT required for the blower. HeaTer WHITE BLACK GROUND WHITE BLACK GROUND blOWer aquatic Industries, Inc. MaIn... - Page 13 Part# 1104PAD Water Sensor Communication Cable Part # 1102SENSOR 20 Minute Timer pump Motor Control for Dedicated Part # pump 15 amp 110vac 8108MOTOR Part # 1103 w/GFCI 2 Pole Breaker 1.5 kw Heater Part # 8095THEAT aquatic Industries, Inc.
- Page 14 Chromatherapy Part # 1025 pump Motor 20 Minute Timer Part # Control for Dedicated 8108MOTOR pump 15 amp 110vac Part # 100820 w/GFCI 2 Pole Breaker 1.5 kw Heater key pad Part # Part # 100667 8095THEAT aquatic Industries, Inc.
-
Page 15: Jet Operations
NOTE: dO NOT STArT PumP uNTiL ALL jETS ArE SuBmErgEd. wATEr LEVEL ShOuLd BE 2” ABOVE highEST jET. jET OPErATiONS: All LuxeAir series jets are removable, and can simply be put into the dishwasher for easy cleaning. (Note: use top rack and remove before drying cycle.) LuxEAir SEriES whirLPOOL jETS The LuxeAir Series combines Full-Size Pressure-Flo hydrotherapy jets, Aquatic rotary massage jets and StressEaz Neck and Shoulder massage jets (most models) to provide an invigorating hydrotherapy experience. - Page 16 OPErATiONS (continued): STrESS-EAz NECK ANd ShOuLdEr jETS (some models): The Aquatic stress-eaz Jet is a rotating jet that concentrates water flow on the user's neck and shoulder areas. • To adjust pressure (see Diagram 11A): 1. grasp the outer ring of the jet.
-
Page 17: Inline Maintenance Heater Operating Instructions
OPErATiON of LuxEAir SEriES jET OPErATiONS (continued): FuLL SizE PrESSurE-FLO hydrOThErAPy jETS: All full-size Pressure-Flo hydrotherapy Jets can be easily interchanged with the hand- held Jet to customize bathing. • To adjust pressure (see Diagram 12A): 1. grasp the outer ring of the jet. -
Page 18: Bathside Control Systems
LuxEAir SEriES CONTrOL PANEL BAThSidE CONTrOL SySTEmS: To Turn Blower (Air System) On: Press once to turn the blower (air system) on. A second press will turn the blower off. Holding the button down for 2 seconds will change modes when the blower is on. -
Page 19: Automated Dry Cycle
The automated dry cycle will turn on for 3 minutes (once the sensors are dry) to purge the air channels after any contact with water, including after a shower or cleaning/rinsing of the bath. The two water sensors are located near the drain. aquatic Industries, Inc. OPErATiON of (see Diagram 11A):... -
Page 20: Purge 24 Hours
PurgE 24 hOurS: It is possible for the user to program a purge cycle that will start every day for a duration of 1 minute. Aquatic strongly recommends activating this feature. The purge cycle will help ensure that the air channels stay dry even when you have taken a soaking bath or shower. - Page 21 4. replace your LeD light (replacement LeD lights can be obtained from Aquatic Industries). 5. verify “O” ring is not damaged and is properly positioned in the groove when replacing the lens. If there is damage or lens does not seal properly, do not refill bathtub.
-
Page 22: Maintenance And Care
Turn ON air bath and run for approximately five minutes. Turn air bath unit OFF and drain tub. Aquatic recommends the above cleaning process on your air bath system once a month. - Page 23 If you are on an individual well, you need to contact a water treatment company to test your water and suggest solutions if a problem is present. aquatic Industries, Inc.
- Page 24 SuPEr SySTEmS CLEAN PLuS manufactured by Stearns Packaging Corporation to rectify this condition. This may be obtained by contacting Aquatic Industries at (800) 555-5324. It is recommended that you follow the instructions provided by the manufacturer with the product. Repeated use may be necessary.
-
Page 25: User Information
Stock No., 004-000-00345-4. Serial Number Location The tub model and serial numbers are located above the pump area on the backside of the bathtub. Your installer should have a service access panel in this location. aquatic Industries, Inc. PLEASE NOTE:... -
Page 26: Jet Cleaning
CLEANiNg: All LuxeAir series jets are removable, and can simply be put into the dishwasher for easy cleaning. see Jet Operation Instructions for removal, pages 15-17. (Note: use top rack of dishwasher and remove before the drying cycle starts.) SurFACE SCrATCh rEmOVAL: Minor scratches may be removed by polishing your tub with a non-abrasive car polish, followed by buffing. -
Page 27: Troubleshooting Guide
Defective control box. Speed of air setting is set too low. SuggESTEd SOLuTiONS Reset gFCI. Contact your electrician. contact Aquatic Industries, Inc. contact Aquatic Industries, Inc. contact Aquatic Industries, Inc. check and reconnect if needed. Contact your electrician. Contact your electrician. -
Page 28: Parts Order Form
2. using map number and letter, choose part number and select color (or finish) on parts list provided on page 32-33. 3. Fill out the form below with the selected information. Fax or send to Aquatic. 4. Call AQUATIC for parts pricing and shipping charges. -
Page 29: Parts Maps
Industries, Inc. - Page 30 LuxEAir SEriES rePLAceMeNT PArTs OrDer MAP/OvervIew 13b. ASSOrTEd FiTTiNgS Fx102 Fx101 Fx103 Coupler y Fitting Street 90 1’’ or 1 1/2” 1’’ only 1/2”, 1” or 1 1/2” 1/2”, 1” or 1 1/2” Blower Blower Control 13d. Fx104 Fx105 fitting T fitting 1”...
- Page 31 LuxEAir SEriES rePLAceMeNT PArTs OrDer MAP 13a. aquatic Industries, Inc.
-
Page 32: Parts List
87swIrLPN 87swIrLsT 87SWIRLWH 85SWIRLBI 85SWIRLBK 85swIrLBN 85SWIRLBO 85SWIRLBR 85SWIRLCH 85SWIRLCL 85swIrLgD 85SWIRLIB 85swIrLPN 85swIrLsT 85SWIRLWH 85AssYwh 85AssYcL 8095TheAT ---------------- 8417sOcKeT 8417sPIgOT ---------------- ---------------- 8408FTg 8150uNION ---------------- 8108MOTOr 1103 1104PAD 100667 1110PADcL 1102SENSOR 1025 8151hvsucvrMe 8151hvsucvrNv 8151hvsucvrwr 8152hvsucvBr aquatic Industries, Inc. - Page 33 FX104 FX104 FX105 FX105 FX106 FX106 FX107 FX107 aquatic Industries, Inc. dESCriPTiON - SPECiFy COLOr/FiNiSh/mOdEL# sucTION cOver - chrOMe sucTION cOver - BIscuIT sucTION cOver - BLAcK sucTION cOver - BONe sucTION cOver - cLeAr sucTION cOver - INNOceNT BLush...
-
Page 34: Aquatic Limited Warranty
ExCLuSiVE rEmEdy Aquatic Industries, Inc. will, at its option, repair or replace (without removal or installation) the affected components of any defective unit or system; repair or replace (without removal or installation) the entire defective unit or system; or refund the then-current list price of the whirlpool, Air Bath, or Tub. In all cases, a reasonable time period must be allowed for warranty repairs to be completed. - Page 36 P.O. Box 889 Leander, Texas 78646-0889 • 11880 rr 2243 w Leander, Texas 78641 (800) 555-5324 FAX: (800) 421-3633 Fax-On-Demand: (877) 618-7024 LAOm6 11/08 www.aquaticwhirlpools.com...