Table of Contents
Advertisement
Quick Links
1.1 - The user guide.................................................................................... 2
1.2 - Safety and security precautions.......................................................... 2
1.3 - Identification plate ...............................................................................3
1.4 - Technical Service Provider................................................................. 3
2.1 - Handling and unpacking...................................................................... 4
2.2 - Control of the accessories................................................................... 6
3.1 - Operating Principles............................................................................ 7
3.2 - Allowed and improper use .................................................................. 8
3.3 - Compliance with EEC Regulations in force ...................................... 8
3.4 - Construction features.......................................................................... 9
3.5 - Technical features..............................................................................10
3.6 - Description of the computer board ....................................................12
4.1 - Place of installation ...........................................................................13
4.2 - Switch from DX (Right) to SX (Left) model ........................................14
4.3 - Installation of the central suction unit ............................................... 16
4.4 - How to connect the pipe network ...................................................... 17
4.5 - Electric system ..................................................................................18
5.1 - Starting of the suction unit .................................................................19
5.2 - Use of the suction unit.......................................................................19
6.1 - Programmed maintenance.................................................................20
6.2 - Unloading of the dust container ........................................................ 21
6.3 - Replacement of the filter cartridge ................................................... 22
6.4 - Reconditioning of the filter cartridge ................................................. 23
7.1 - Servicing criteria ............................................................................... 23
8 Computer programming for the maintenance
8.1 - General information.......................................................................... 24
8.2 - Personalization of the maintenance parameters ............................ 25
8.3 - Visualization of personalized maintenance parameters ................. 27
8.4 - Modify the parameters of a personalized maintenance .................. 28
9.1 - Spare parts list.................................................................................. 29
10.1 - General provisions ........................................................................... 29
11 Technical Problems
11.1 - Troubleshooting................................................................................ 30
TA-TE 02/04-01
Installation, use and maintenance guide
INDEX
1
(only TECNO ACTIVA line)
Advertisement
Table of Contents
Related Manuals for SISTEM AIR MINI TE
Summary of Contents for SISTEM AIR MINI TE
-
Page 1: Table Of Contents
Installation, use and maintenance guide INDEX 1 General Information 1.1 - The user guide..................2 1.2 - Safety and security precautions............2 1.3 - Identification plate ................3 1.4 - Technical Service Provider..............3 2 Unpacking 2.1 - Handling and unpacking..............4 2.2 - Control of the accessories.............. -
Page 2: General Information
Installation, use and maintenance guide 1 - GENERAL INFORMATION 1.1 The User Guide The user guide is a fundamental document written by the builder, to be considered an integral part of the central suction unit. In case of resale, offering or lease to third parties, the user guide must be handed over to the new user or to the new owner. -
Page 3: Identification Plate
Technical Data of the Electric Motor 1.4 Technical Service Provider Call the Builder Technical Service or contact SISTEM AIR authorized centers for any information you may need. Always specify the technical data indicated on the identification plate and the serial number of the central suction unit. -
Page 4: Unpacking
Installation, use and maintenance guide 2 - UNPACKING 2.1 Handling and unpacking Follow the instructions printed on the cardboard box to move the suction unit to the location selected for the installation. If necessary, use a trolley to move the suction unit or ask somebody to help you. Arrange the cardboard box on the floor, with the opening side upward and cut the adhesive tape. - Page 5 Installation, use and maintenance guide Open the box, take the straps with both hands and lift the suction unit.Arrange it on the floor in a horizontal position. Cut the straps. Remove the upper cardboard protection, lift the suction unit and arrange it on the floor in a vertical position.
-
Page 6: Control Of The Accessories
Installation, use and maintenance guide 2.2 Control of the accessories Check what you have received: - One central suction unit - One metal frame for hanging the suction unit on the wall - Two couplings made of plastic to connect the suction pipes - Four metal clamps for fixing the couplings - An adhesive plate showing the Builder's trademark - One user guide for correct installation, use and maintenance... -
Page 7: Description Of The Central Suction Unit
Installation, use and maintenance guide 3 - DESCRIPTION OF THE CENTRAL SUCTION UNIT 3.1 Operating principles The central suction system, suitable for any kind of residential building (house, office, hotels, service building) consists of a net of PVC pipes spreading out in every room and perfectly chased in walls and false ceilings. -
Page 8: Allowed And Improper Use
Installation, use and maintenance guide 3.2 Allowed and improper use The SISTEM-AIR central suction unit model SA..., has been designed to remove the dust, small-size solid bits and pieces and dry materials. It is forbidden to use the suction system to remove textile stuff, big-size bits and pieces, burning and hot materials. -
Page 9: Construction Features
Installation, use and maintenance guide 3.4 Construction features (see picture) The TECNO Line single-phase suction units for civil sector are divided in two main categories: TECNO Evolution Line (models SA... TE) TECNO Activa Line (models SA... TA) The two lines of products, equipped with the same motor power, feature the same construction technology and grant the same performances. -
Page 10: Technical Features
Installation, use and maintenance guide Technical features (See picture and table) TA-TE 02/04-01... - Page 11 Installation, use and maintenance guide TA-TE 02/04-01...
-
Page 12: Description Of The Computer Board
Installation, use and maintenance guide 3.6 Description of the computer board (see picture) (only for TECNO Activa line) 1 - PROG Led It switches on when the computer programming function has been activated 2 - PIN Led It switches on when the computer programming function has been activated to display the PIN code 3 - FILTER CARTRIDGE CLEANING WARNING MESSAGE Led If on , it indicates that the filter cartridge must be cleaned... -
Page 13: Installation
Installation, use and maintenance guide 4 - INSTALLATION - ATTENTION - THE UNDERMENTIONED OPERATIONS MUST BE CARRIED OUT BY QUALIFIED STAFF 4.1 Place of installation Before installing the central suction system, a suction pipes network must installed by qualified staff. The qualified operators must also spot the best location to install the suction unit. -
Page 14: Switch From Dx (Right) To Sx (Left) Model
Installation, use and maintenance guide 4.2 Switch from DX (right) to SX (left) model The suction units included in the TECNO line are usually delivered suction and exhaust pipes connections assembled on the right side of the unit (DX model); when necessary, it is possible to switch the suction unit from DX (right) to SX (left) model by assembling the inlets of the pipes on the left side (SX model). - Page 15 Installation, use and maintenance guide Plug the card cable in the special guides and assemble the dustproof spongy disk to seal the opening (Only for TECNO Activa Line). Assemble the top cover. Assemble the fixing plate. Fix the adhesive plate supplied with the central suction unit.
-
Page 16: Installation Of The Central Suction Unit
Installation, use and maintenance guide 4.3 Installation of the central suction unit You must use the special frame (provided with the suction unit) and the special screws to hang the central suction unit firmly and permanently to a wall. Remember that the suction unit must hold up the equivalent of eight times the weight of the suction unit (please refer to par. -
Page 17: How To Connect The Pipe Network
Installation, use and maintenance guide How to connect the pipe network (see picture) - Use the correct fitting to connect the suction unit to the suction hose - Use the correct fitting to connect the suction unit to the air exhaust pipe - Stick the silencer on the exhaust pipe near the exhaust grid TA-TE 02/04-01... -
Page 18: Electric System
Installation, use and maintenance guide Electrical connection ATTENTION: The electrical connection must be carried out by duly qualified staff ONLY Before plugging in the suction unit, make sure that the mains power supply corresponds to the central suction unit power supply (please refer to data indicated on the identification plate). -
Page 19: How To Use The Central Suction Unit
Installation, use and maintenance guide 5 - HOW TO USE THE CENTRAL SUCTION UNIT 5.1 Starting of the suction unit Press the start push-button. A red lamp will light up inside. 5.2 Use of the suction unit Fit the accessory suitable for the cleaning operations you want to carry out in the hose. -
Page 20: Maintenance
Installation, use and maintenance guide 6 - MAINTENANCE - ATTENTION - ALWAYS UNPLUG THE POWER SUPPLY CABLE FROM THEPOWER SUPPLY SOCKET AND ALWAYS WEAR PROTECTION GLOVES AND GOGGLES BEFORE CARRYING OUT ANY TECHNICAL OR MAINTENANCE OPERATION 6.1 Programmed maintenance In order to keep the system perfectly operating and to avoid any possible mechanic trouble, the user must overhaul the whole system at precise time intervals, according to the accumulated operating time of the central suction system. -
Page 21: Unloading Of The Dust Container
Installation, use and maintenance guide 6.2 Unloading of the dust container Disassemble the dust container. Remove the conveyor cone. Unload the dust container. Assemble the conveyor cone. Reassemble the dust container. After restarting the central suction unit, press the RESET key. (only for TECNO Activa Central suction unit) TA-TE 02/04-01... -
Page 22: Replacement Of The Filter Cartridge
Installation, use and maintenance guide 6.3 Replacement of the filter cartridge Disassemble the dust container. Unscrew the locking handle.. Replace the filter cartridge. Screw the locking handle. Reassemble the dust container. After restarting the central suction unit, press the RESET key. (only for TECNO Activa Central suction unit) TA-TE 02/04-01... -
Page 23: Reconditioning Of The Filter Cartridge
Installation, use and maintenance guide 6.4 Reconditioning of the filter cartridge - ATTENTION - NEVER USE THE SUCTION UNIT WITHOUT THE FILTER. BEFORE CARRYING OUT THE OPERATION DESCRIBED HEREUNDER, ALWAYS ASSEMBLE A NEW CARTRIDGE. The filter cartridge can be reconditioned many times; use the corner nozzle of your suction unit to clean the filtering surface of the cartridge. -
Page 24: General Information
Installation, use and maintenance guide 8 - MAINTENANCE COMPUTER PROGRAMMING (only for TECNO Activa Central suction unit) 8.1 General information Your TECNO Activa motor is programmed in order to warn you for its scheduled cleaning and or a misfunction of its motor. If necessary, the parameters stored in the computer can be modified to suit specific needs. -
Page 25: Personalization Of The Maintenance Parameters
Installation, use and maintenance guide 8.2 Personalization of the maintenance parameters With this procedure your central vacuum is allowed to receive the designed maintenance programs wich swit you. Herewith the values set by the manufactrer can be modified through the installed computer (see the pre-stored values at par. 8.1). ATTENTION: for further changes of the maintenance parameters, use the procedure of par. - Page 26 Installation, use and maintenance guide 14 - Press the button . The led CLEANING FILTER CARTRIDGE ALARM will switch off and the led DUST CONTAINER UNLOADING ALARM will switch on. On the display the number 1 will appear. 15 - With the buttons compose the number (from 1 to 9) which will indicate after how many hours the alarm should go off.
-
Page 27: Visualization Of Personalized Maintenance Parameters
Installation, use and maintenance guide 8.3 Displaying of the personalised maintenance parameters The following procedure allows to display the personalised maintenance parameters without changing the set values. 1 - Verify that the machine is connected to the main power supply but not running, (the led is off and the led is on). -
Page 28: Modify The Parameters Of A Personalized Maintenance
Installation, use and maintenance guide 8.4 Modifying the personalised maintenance parameters The following procedure allows you to modify the personalised maintenance parameters. ATTENTION: Any new change will cancel the previously inserted data. 1 - Verify that the machine is connected to the main power supply but not running, (the led is off and the led is on). -
Page 29: Recommended Spare Parts
SISTEM-AIR spare parts. Please find below a list of spare parts. Description Quantity Spare Part Code Central Suction Unit Model - Mini TE Filter Cartrige 1610.5 - Mini TA - Media TE - Media TA - Media PLUS TE - Media PLUS TA... -
Page 30: Troubleshooting
Installation, use and maintenance guide 11.1 Troubleshooting Problem Possible causes Possible corrective measures The power supply cable is Plug in the power supply unplugged cable The start push-button of Press the start the central suction system push-button is unplugged No air suction in all air inlets The start signal cable is Plug in the start cable...
Need help?
Do you have a question about the MINI TE and is the answer not in the manual?
Questions and answers