Page 1
MINIFLEX 5-BF III ® Series Name Part No. Type 20403-0**E STANDARD TYPE 20456-0**E WIDE CONTACT GAP TYPE MINIFLEX 5-BF II 20477-0**E type-i (STANDARD TYPE) 20478-0**E type-i (WIDE CONTACT GAP TYPE) MINIFLEX 5-BF III 20593-0**E-01# Instruction Manual S19612 October 1, 2019 R.Morita...
Page 2
Document No. MINIFLEX 5-BF II & MINIFLEX 5-BF III Instruction Manual HIM-06004 1. 使用上の注意 (NOTICE) 1-1. 操作時の注意事項 (Notes at the time of operation) ハウジング/Housing FPC/FFC アクチュエータ/Actuator コンタクト/Contact ホールドダウン/Hold Down Fig.1. アクチュエータロック解除状態 (Actuator un-lock state) 回転/Rotation アクチュエータ溝部/The slot on the actuator Fig.2.
Page 3
Document No. MINIFLEX 5-BF II & MINIFLEX 5-BF III Instruction Manual HIM-06004 (2) FPC/FFC を未挿入状態でのアクチュエータのロック操作は避けてください。 接点間が狭くなり、FPC/FFC 挿入力が上昇する恐れがあります。 Please avoid actuator lock operation at the time of FPC/FFC un-inserting. Contact point gap becomes narrow and it becomes the cause by which FPC/FFC insertion power goes up.
Page 4
Document No. MINIFLEX 5-BF II & MINIFLEX 5-BF III Instruction Manual HIM-06004 ○ Fig.4. アクチュエータロック解除方法 (The release operation method of Actuator) × Fig.5. アクチュエータ NG 操作方法 (The actuator NG operation method) (6) アクチュエータをロックした状態での FPC/FFC の挿入、引き抜きは行わないでください。 FPC/FFC 破損、コンタクト変形などによる接触不良の原因となります。 Please do not perform insertion and drawing out of FPC/FFC in the state where the actuator was locked.
Page 5
Document No. MINIFLEX 5-BF II & MINIFLEX 5-BF III Instruction Manual HIM-06004 1-2. 設計時の注意事項 (Notes at the time of a design) (1) FPC/FFC の引き回しは、コネクタに直接力が掛からないように行ってください。 コネクタに力が掛かる状態での使用は、接触不良の原因となります。 Please perform leading about of FPC/FFC so that direct power is not applied to a connector.
Page 6
Document No. MINIFLEX 5-BF II & MINIFLEX 5-BF III Instruction Manual HIM-06004 1-3. 実装時の注意事項(Notes at the time of mounting) (1) リフロー条件は、弊社推奨のリフロー条件内でご使用ください。 但し、基板サイズや半田の種類により実装状態が変わる場合がありますので、実装状態を御確認のうえ、御使用ください。 Please use conditions reflow within the reflow condition of recommendation of our company. However, please use it after checking a mounting state because a mounting state may change according to the size of a PCB and the kind of solder.
Page 7
Document No. MINIFLEX 5-BF II & MINIFLEX 5-BF III Instruction Manual HIM-06004 (3) 手半田による実装の際は、次の点にご注意ください。 ・手半田条件: 350℃、 5 秒以内 ・過度に半田を付けないでください。半田上がりの原因となります。 ・半田ゴテをコンタクト及びホールドダウンに押し付けないでください。 コンタクト及びホールドダウン変形の原因となります。 ・コンタクト及びホールドダウン部以外に半田ゴテを当てないでください。 コネクタ変形の原因となります。 Be careful of the following point in the case of mounting with hand soldering. ・Hand soldering condition: 350℃, 5sec. MAX.
This manual is also suitable for:
Miniflex 5-bf iii20593-008e-0120593-010e-0120593-012e-0120593-014e-0120593-018e-01...
Show all