Victron energy MultiPlus Quick Manual
Inverter/charger battery back-up - 500va to 1600va
Hide thumbs
Also See for MultiPlus:
- Operational manual (7 pages) ,
- Manual (13 pages) ,
- Manual (26 pages)
Table of Contents
Advertisement
Quick Links
TDS | QUICK GUIDE
Victron MultiPlus
Inverter/Charger Battery Back-Up - 500VA to 1600VA
© Newton Waterproofing Systems
Newton House, 17-20 Sovereign Way
Tonbridge, Kent, TN9 1RH
www.newtonwaterproofing.co.uk
tech@newtonwaterproofing.co.uk
+44 (0)1732 360 095
Revision 1.0 - 17
November 2021
th
Opening Hours:
Monday to Thursday 8:00am - 5:30pm
Friday 8:00am - 5:00pm
®
Advertisement
Table of Contents
Related Manuals for Victron energy MultiPlus
Summary of Contents for Victron energy MultiPlus
- Page 1 TDS | QUICK GUIDE ® Victron MultiPlus Inverter/Charger Battery Back-Up - 500VA to 1600VA Revision 1.0 - 17 November 2021 www.newtonwaterproofing.co.uk © Newton Waterproofing Systems Opening Hours: tech@newtonwaterproofing.co.uk Newton House, 17-20 Sovereign Way Monday to Thursday 8:00am - 5:30pm Tonbridge, Kent, TN9 1RH...
- Page 2 This Quick Guide should be read in conjunction with the Victron Installation Manual that is included within the product packaging. If the Victron manual is not within the packaging, please download from the Victron website at the following addresses: 500VA & 800VA - www.victronenergy.com/upload/documents/Manual-MultiPlus-500VA-1200VA-EN-NL- FR-DE-ES-IT.pdf 1600VA - www.victronenergy.com/upload/documents/Manual-MultiPlus-1600VA-EN-NL-FR-DE-ES-IT.pdf...
- Page 3 INTRODUCTION INCLUDED WITHIN THE PACKAGING The inverter is supplied in two boxes. Within the larger box is the inverter. Within the second box are the ancillary products that are required for installation of the inverter. The battery(s) are be supplied in separate packaging.
- Page 4 WARNINGS & INSTALLATION WARNING: ELECTRIC SHOCK HAZARD The product is used in conjunction with a permanent energy source (battery). Input and/or output terminals may still be dangerously energised, even when the equipment is switched off. Always switch off the AC supply and the battery isolator switch before carrying out maintenance or servicing the product. Read the installation instructions in the installation manual before installing the equipment.
-
Page 5: Installation
INSTALLATION ENVIRONMENT This product should be installed in a heat-resistant, dry, habitable environment. Prevent the presence of chemicals, synthetic components, curtains or other textiles, etc., in the immediate vicinity. WARNING: Do not install within damp or dank indoor or outdoor environments as dampness and even insects can cause electrical shorting of main board and components which is not covered by the product warranty. - Page 6 INSTALLATION FIG A - 500VA & 800VA FIG B - 1600VA For more information visit us online www.newtonwaterproofing.co.uk...
- Page 7 INSTALLATION AC POWER OUT TO PUMP OR CONTROL PANEL 1. Remove the right (AC OUTPUT) wiring block from the base of the inverter (item J) 2. Wire AC OUTPUT with correctly rated mains cable to the AC isolator switch and to the RCD fused spur.
-
Page 8: Temperature Sensor
INSTALLATION TEMPERATURE SENSOR Insert the Temperature Sensor cable into terminal D of the Inverter/Charger. WARNING: If the Temperature Sensor Cable is not correctly fitted, the charger will not charge the batteries. OPERATION The Inverter/Charger is now ready to use. Switch the unit on at the plug or switched spur. Switch on the Inverter/Charger via the ON/OFF switch at the bottom on the unit. - Page 9 INSTALLATION LED INDICATIONS - Switch position - OFF No mains 230 VAC - Pumps powered by 12 VDC power inverted to 230 VAC At initial start and also when mains 230 VAC power has failed and the pumps/panel are powered by the inverter using 12 VDC from the battery. This condition is only normal during a mains power outage.
-
Page 10: Maintenance
CONFIGURATION & WARRANTY CONFIGURATION • Settings should be carried out by a competent person • Carefully read the instructions before changes are made • Batteries should be in a dry and well-ventilated area during charging Standard settings: ready for use On delivery, the unit has been programmed by Newton ready for use as part of a Newton Pumping System with charging voltages matched to the battery bank size also supplied by Newton Waterproofing Systems. -
Page 11: Troubleshooting
TROUBLESHOOTING TROUBLESHOOTING The following table provides a quick reference of the more common faults. Disconnect the battery/ batteries and pumping systems before diagnosing the fault. Consult Newton Waterproofing Systems if the fault cannot be resolved. Call us for more information on +44 (0)1732 360095... - Page 12 Victron MultiPlus Inverter/Charger Battery Back-Up - 500VA to 1600VA TROUBLESHOOTING CONTINUED Newton Waterproofing Systems reserve the right to update product literature at any time. Please always refer to our website for the latest versions. www.newtonwaterproofing.co.uk © Newton Waterproofing Systems Opening Hours: tech@newtonwaterproofing.co.uk...