Advertisement
Quick Links
Single Color Wall Mounted ZigBee Remote Controller
Important: Read All Instructions Prior to Installation
Function introduction
Press and hold down both keys together to search and
pair to ZigBee network or factory reset the controller.
Group 1
Click to turn on. Press and
hold down to increase
light intensity.
Group 2
Group 3
Group 4
11 mm
Battery: CR2450
Before the first use, please remove the protective film
Group 1
Click to turn off. Press and
hold down to decrease
light intensity.
Group 2
Group 3
Group 4
Note: This remote
supports 4 groups for
binding max. 30 lighting
devices.
Front side
71.20 mm
55.57 mm
The remote control can be fixed on
the wall with 3M glue or screw.
Back side
Product Data
70100005
Operation Frequency
Transmission Range
(free field)
Power Supply
Operating temperature
Relative humidity
Dimming Range
Dimensions
Protection Type
ZigBee Clusters Supported by This Remote Are As Follows:
Input clusters:
• Basic
• Power Configuration
Output clusters:
• Identify
• On/off
• Group
Safety & Warnings
• This device contains a button lithium battery that shall be stored and disposed properly.
• DO NOT expose the device to moisture.
Quick Start (Simplified operation compared to standard operations in the part "Operation")
Touchlink + Add Group 1: Press and hold
down both keys for 3 seconds to start
touchlink and
link
light device to group 1.
Touchlink + Add Group 2: Press and hold
down both keys for 3 seconds to start
touchlink and
link
light device to group 2.
Touchlink + Add Group 3: Press and hold
down both keys for 3 seconds to start
touchlink and
link
light device to group 3.
Touchlink + Add Group 4: Press and hold
down both keys for 3 seconds to start
touchlink and
link
light device to group 4.
Factory reset: click both buttons 3 times to
reset the remote (the remote should already
be paired to a gateway).
• ZigBee dim remote based on ZigBee 3.0
2.4GHz
• Enables to control both single color lighting devices
30m
• Battery powered remote with low power consumption
• Enables to pair ZigBee lighting devices via touchlink
3VDC (CR2450)
commissioning without coordinator
0-40°C
• Supports find and bind mode to pair with ZigBee lighting
devices
8% to 80%
• Supports 4 groups for binding max. 30 lighting devices
0.1%-100%
• 2.4 GHz global operation
• Transmission range up to 30m
71.2x71.2x13.6mm
• Compatible with universal ZigBee Gateway products
IP20
• Compatible with universal single color ZigBee lighting
devices
• Identify
• Diagnostics
• Level control
• Ota
Network pairing mode: click both buttons 3 times to
set the remote into network pairing mode (the remote
should not belong to any gateway network).
Advertisement
Related Manuals for ZIGBEE SR-ZG9001K8-DIM
Summary of Contents for ZIGBEE SR-ZG9001K8-DIM
- Page 1 Function introduction commissioning without coordinator Operating temperature 0-40°C • Supports find and bind mode to pair with ZigBee lighting Press and hold down both keys together to search and devices pair to ZigBee network or factory reset the controller. Relative humidity 8% to 80% •...
- Page 2 Step 3: Short press ON button of group 1/2/3/4 to choose a group Note: 1) Directly TouchLink (both not added to a ZigBee network), please first factory reset both the Step 5: Immediately short press that the device was touchlink remote and device, each remote can link with max.
- Page 3 30 lighting devices. Each lighting device can be linked by max. 30 remotes. 13. OTA The remote supports firmware updating through OTA, and will acquire new firmware from zigbee controller or 10. Find and Unbind a Zigbee Lighting Device hub every 10 minutes automatically.
- Page 4 Installation 1.Remove battery insulator ① ②Pull out the ③Install the silicone Use tool to open the silicone gel battery cover battery insulator battery cover back 2.Install the controller to wall(2 methods) Method 1:Stick 3M glue on the Method 2:Screw the bracket back of the bracket and then stick to the wall the bracket to the wall...