Download Print this page

Air Lift Slam Air 59111 Instructions Manual

Fits multi-leaf steel spring models only.

Advertisement

Quick Links

Fits Multi-Leaf Steel Spring Models Only.
P/N 59111–This kit is for a 2" drop
Please read these instructions completely before proceeding with the installation.
Figure 1
CAUTION: Failure to maintain correct minimum pressure (or pressure proportional to the load), bottoming out, over–
extension, or rubbing against another component will void the warranty.
IMPORTANT: If your vehicle is equipped with rear air conditioning it will be necessary to move the lines up to the top of
the frame to install the air spring kit.
IMPORTANT: Your air springs will last much longer if they are not the suspension limiter in either compression or
extension. The air spring compresses to 2.2" and extends to 7.1". Keeping the minimum required pressure or a pressure
proportional to the load will prevent bottoming out. The shock absorber is usually the limiter on extension. If this is not
the case, you should consider the use of limiting straps. The maximum inflated diameter of your air spring is 4.6". You
must check to see that nothing is rubbing against the air spring within this diameter.
This kit contains the new Air Lift installation tool. This tool is designed to simplify the installation of the kit for correct
mounted height and alignment. The threaded section of the tool will ensure mounting of the air spring within the 4.0" to
5.0" design envelope. The air spring may be mounted anywhere within that range. It may be necessary to "flip" the
upper bracket to achieve the correct design height.
Upper
Bracket
Installation
Tool
1
by
Nylon Nut
Flat Side Up
Lower
Bracket
1/2" Flat Washer
1/2" HHCS
MN-346
(03006)
ECN3100

Advertisement

loading
Need help?

Need help?

Do you have a question about the Slam Air 59111 and is the answer not in the manual?

Questions and answers

Summary of Contents for Air Lift Slam Air 59111

  • Page 1 This kit contains the new Air Lift installation tool. This tool is designed to simplify the installation of the kit for correct mounted height and alignment. The threaded section of the tool will ensure mounting of the air spring within the 4.0" to 5.0"...
  • Page 2 Swivel Air Line 3/8" Nylon Elbow Fitting Lock Nut Oversized Washer Frame Nylon Nut 3/8"-16x 4" Bolt Upper Bracket 3/8" U-Bolt Upper Leaf Spring Lower Retainer Plate Bracket 1/2" Flat Washer 1/2" HHCS Clamp 3/8" Flat Washer Nylon Lock Nut Figure 2 Centering Pin Spacers - Optional FORWARD...
  • Page 3 59111 is a side mount kit – between the frame and tire. Due to the wide variety of lowering kits on the market, Air Lift cannot guarantee that this kit will fit every vehicle. You may need to modify the upper bracket, or...
  • Page 4 (4) Remove centering pin and install one spacer per pin. Reinstall pin (Inset A). If nut does not have full thread contact, replace centering pin. Set L-bracket on leaf with the pin through the slot. Make sure that the post part of the “L”...
  • Page 5 (4) Rotate the upper bracket back to the original location and install the frame bolt, flat washer, and lock nut USE THE SELF TAPPING BOLTS IN THESE HOLE LOCATIONS through the second hole that was drilled. Now tighten both of the installed fasteners to 20 ft–lbs. Centerpunch and drill a third "...
  • Page 6 12. Route air line along frame from the inflation valve location to the air springs (Figure 9). Use the provided clips and self tapping screws to attach to the outside of the frame rail and the air line sleeves to protect the air line when routing through existing holes in the frame.
  • Page 7: Maintenance And Operations

    Gross Vehicle Weight Rating (GVWR), which may be less than 100 p.s.i. Check your vehicle owner’s manual and do not exceed maximum loads listed for your vehicle. When inflating your Air Lift air spring, add pressure in small quantities, checking pressure frequently during inflation.
  • Page 8 Thank you for purchasing Air Lift Products Mailing Address: Street Address: AIR LIFT COMPANY AIR LIFT COMPANY P.O. Box 80167 2710 Snow Rd. Lansing, MI 48908-0167 Lansing, MI 48917 Local Phone: (517) 322-2144 Fax: (517) 322-0240 For Technical Assitance call 1-800-248-0892 “The Choice of the Professional Installer”...
  • Page 9: Product Use Information

    No. Adding air springs will not change the weight ratings (GAWR, GCWR and/or GVWR) of a vehicle. Exceeding the GVWR is dangerous and voids the Air Lift warranty. Q. Is it necessary to keep air in the air springs at all time and how much pressure will they need? The minimum air pressure should be maintained at all times.
  • Page 10: Warranty And Returns Policy

    The consumer is responsible for installation/reinstallation (labor charges) of the product. Air Lift Company reserves the right to change the design of any product without assuming any obligation to modify any product previously manufactured.