Technical Data; Charging Procedure; Recharging Batteries - Yamato CD 12 L Instruction Manual

TECHNICAL DATA

Model
Code
Voltage
Battery Type
Battery Capacity
Charger voltage
Speed
No Load speed (rpm)
Impact rate (bpm)
Torque settings
Max Torque
Chuck
Impact
Second battery
Charging time
Sound pressure level (L
dB(A)
Sound power level (L
dB(A)
Vibration level
Drilling
Vibration level
Impact drilling

CHARGING PROCEDURE

NOTE: Before using the tool, read the instruction book carefully.

1. RECHARGING BATTERIES

A) CHARGING THE BATTERY The battery charger supplied is matched to the Li-ion battery installed in
the machine. Do not use another battery charger. The Li-ion battery is protected against deep
discharging. When the battery is empty, the machine is switched off by means of a protective
circuit: The chuck no longer rotates. In a warm environment or after heavy use, the battery pack
may become too hot. Allow time for the battery to cool down before recharging. When the
battery pack is charged for the first time and after prolonged storage, the battery will only accept
approximately 60% charge. However, after several charge and discharge cycles the battery will
accept a 100% charge.
B) IMPORTANT NOTES FOR CHARGING THE BATTERY The battery in your new tool is not charged when
it leaves the plant. Therefore it must be charged for 1 hour before using the first time!
C) CHARGING Plug the charger plug into a suitable mains socket, and the indicator light will shoe
green. Then insert the battery pack into the charger, the indicator light will become red to indicate
CD 12 L
99360
12 volt
Li-ion
1,5 Ah
230V-50Hz
2
0~350/0~1350
-
18 + 1
20 Nm
10 mm
NO
NO
1 h
)
68,2 dB(A)
pA
K =3 dB(A)
pA
)
79,2 dB(A)
WA
K =3 dB(A)
WA
1,552 m/s
2
K=1,5 m/s
2
-
thet charging is taking place.
The three green intelligent battery indicators will continue
flashing when start charging. Two indicators will flash inturn
when the capacity reach 70%. One indicator light flash when
100% charged. Three indicators will keep light when finished
charging. After a few seconds, the indicators will off.
After charging 1 hour, the battery will be fully charged, the
light will turn to green. Unplug the charger plug from the wall
socket, the tool is ready to use.
CD 16 L CDP 16 L
99361 99362
16 volt 16 volt
Li-ion Li-ion
2,0 Ah 2,0 Ah
230V-50Hz 230V-50Hz
2 2
0~350/0~1250 0~350 / 0~1250
- 0~5250/0~18750
19 + 1 16
28 Nm 33 Nm
10 mm 13 mm
NO YES
NO YES
1 h 1 h
84 dB(A) 84 dB(A)
K =3 dB(A) K =3 dB(A)
pA pA
95 dB(A) 95 dB(A)
K =3 dB(A) K =3 dB(A)
WA WA
1,552 m/s 1,552 m/s
2
K=1,5 m/s K=1,5 m/s
2
7,528 m/s
-
K=1,5 m/s
15
CDP 20 L
99363
20 volt
Li-ion
2,0 Ah
230V-50Hz
2
0~350 / 0~1250
0~5250/0~18750
16
35 Nm
13 mm
YES
YES
1 h
84 dB(A)
K =3 dB(A)
pA
95 dB(A)
K =3 dB(A)
WA
1,552 m/s
2 2
K=1,5 m/s
2 2
7,528 m/s
2 2
K=1,5 m/s
2 2