Related Manuals for Cooke & Lewis CLBUDO89
Summary of Contents for Cooke & Lewis CLBUDO89
- Page 1 5059340094113 CLBUDO89 V21020 BX220IM 5059340094113-C&L-A4-IM-Easy-V10.indd 1 5059340094113-C&L-A4-IM-Easy-V10.indd 1 29/10/2020 3:20 PM 29/10/2020 3:20 PM...
- Page 2 Contents Installation Care and Maintenance 5059340094113-C&L-A4-IM-Easy-V10.indd 2 5059340094113-C&L-A4-IM-Easy-V10.indd 2 29/10/2020 3:20 PM 29/10/2020 3:20 PM...
- Page 3 IMPORTANT - Please read carefully the separate safety guide before use. [02] x 2 [03] x 1 [04] x 1 [01] x 1 [05] x 1 [10] x 8 [06] x 2 [08] x 2 [07] x 2 [09] x 2 Ø4 x 16 mm Ø4 x 25 mm Not included...
- Page 4 Installation EN Before you start • This appliance must be installed correctly by a qualified person, strictly following the manufacturer’s instructions. WARNING: Danger of electric shock! The power supply must be cut off before the appliance is installed completely. • Only a qualified person in compliance with the instructions provided can install the appliance. The manufacturer declines all responsibility for improper installation, which may harm persons and animals and cause damage.
- Page 5 Installation [09] x 2 Ø4 x 16 mm [10] x 8 [11] x 2 [11] Installation of Built-under ovens • For correct installation under the work surface, first attach two 18 mm clad-on end panels to the adjacent surfaces of the cabinets - step 01a.
- Page 6 Installation [10] [09] x 2 Ø4 x 16 mm [10] x 8 [10] [09] 5059340094113-C&L-A4-IM-Easy-V10.indd 6 5059340094113-C&L-A4-IM-Easy-V10.indd 6 29/10/2020 3:20 PM 29/10/2020 3:20 PM...
- Page 7 Installation Upper vent ≥10 mm ≥35 mm The diagram above shows the air circulation requirements including a slot that should be cut into the plinth if fitted. (Note: cabinet legs and clad-on end panels [11] not shown for clarity). It is essential when installing your oven there is adequate air circulation around the appliance to ensure the correct operation of the appliance.
- Page 8 Installation [01] x 1 IMPORTANT: Do not lift the appliance by the door handle to avoid potential damage to the glass and hinges. CAUTION! If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons in order to avoid safety hazards. 5059340094113-C&L-A4-IM-Easy-V10.indd 8 5059340094113-C&L-A4-IM-Easy-V10.indd 8 29/10/2020 3:20 PM...
- Page 9 Installation [08] [06] [07] [06] x 2 [07] x 2 [08] x 2 Once the oven has been lifted into place on the two brackets, locate the two holes in the casing of the oven and fix it into place to the clad-on end panels [11] using [06], [07] and [08]. CAUTION: Do not over-tighten the screws [06] to avoid damage to the oven or appliance housing –...
- Page 10 Installation Electrical Installation All installation must be carried out by a competent person or qualified electrician. Before connecting the mains supply ensure that the mains voltage corresponds to the voltage on the rating plate. Direct Connection The appliance must be connected directly to the mains using an omnipolar circuit breaker with a minimum opening of 3 mm between the contacts.
- Page 11 EN Before you start WARNING: Read the instructions before using the appliance. CAUTION: Accessible parts may be hot when the grill is used – keep young children away. CAUTION: Always use oven gloves when removing cookware from the oven. Oven layout Control panel Mains cable (at rear, not shown) Fixing holes (x2)
- Page 12 Oven controls Function control knob of Top oven Temperature control knob of Top oven Control panel Function control knob of Main oven Temperature control knob of Main oven Temperature indicator of Top oven Temperature indicator of Main oven Operational modes Top oven Icon Function / Feature...
- Page 13 Control panel Turn on the power supply at the main consumer unit, and your oven is ready for its initial set up. Note: the Clock must be set before first use. Function button Cooking duration icon Minus button Controls locked icon Plus button Clock icon Lock button...
- Page 14 Setting the Cooking duration and End times - Main oven only These functions can be used to program the cooking times in the Main oven so that cooking finishes as required and the oven switches off the power automatically. Cooking duration can be set for a finite length of time. Additionally, the End time can be set so that the Cooking duration then finishes at the time you need.
- Page 15 Lock function • Press and hold the Lock button for three seconds to freeze the Control Panel. Press and hold the button again for three seconds to unfreeze the panel. • Once the Control panel is locked, the oven will beep if any button is pressed. IMPORTANT: the rotary controls will still operate in Locked mode.
- Page 16 Using the Fan assisted oven - Main oven 1. Select Fan assisted oven on the right rotary control. 2. Select the temperature required on the right rotary control and the Indicator light will come on to allow pre-heating to start. This can take up to fifteen minutes before the correct temperature is reached. 3.
- Page 17 [04] [05] [04] x 1 [05] x 1 [03] [03] x 1 [05] [05] x 1 [02] [02] x 2 5059340094113-C&L-A4-IM-Easy-V10.indd 17 5059340094113-C&L-A4-IM-Easy-V10.indd 17 29/10/2020 3:20 PM 29/10/2020 3:20 PM...
- Page 18 Care and Maintenance EN General • It is important to clean the product regularly as excessive fat and grease can affect performance and cause a fire hazard. • Always switch off your appliance and allow it to cool down before cleaning. •...
- Page 19 Care and Maintenance Cleaning the side rails and covers 1. Remove all the accessories from the inside of the oven. 2. Carefully remove the side rails from the covers as shown. 3. Remove the side covers from the inside of the oven. 4.
- Page 20 Care and Maintenance Removing oven parts for cleaning • To remove the door, open the door to the maximum angle. Then pull the buckle at the door hinge backward. • Close the door to an angle approximately 30°. Hold the door with one hand on each side. Lift up and slowly pull the door out from the oven.
- Page 21 Care and Maintenance Bulb replacement - cold oven only 1. Switch off the power at the main circuit breaker. 2. Carefully unscrew the cover by turning it counter-clockwise. 3. Replace the bulb and screw the cover back in place. NOTE: Only use 25-40 W / 220 V-240 V, T300°C G9 halogen lamps. Handle with a soft cloth to avoid premature failure.
- Page 22 Addresses Manufacturer: UK Manufacturer: Kingfisher International Products Limited, 3 Sheldon Square, London, W2 6PX, United Kingdom EU Manufacturer: Kingfisher International Products B. V . Rapenburgerstraat 175E 1011 VM Amsterdam The Netherlands www.kingfisher.com/products www.diy.com www.screwfix.com www.screwfix.ie To view instruction manuals online, visit www.kingfisher.com/products Customer Helpline (Freephone) UK 0800 324 7818 uk@kingfisherservice.com...