Misc. Settings Menu.............29 Flags ..............29 Dimmer Readback ...........31 Double Bump ..........32 LCD Backlight ..........33 Time Master ............34 Old Code Compatibility........35 IR Control ............36 Astronomical Clock Setup .........36 Max. Number of Zones Setup ......38 Leviton D4200 LCD Ver 2.0 Architectural Lighting Controller...
Page 4
Changing the MAX and OFF Lighting Levels ......62 Using the Optional Remote Control ........63 Viewing Scheduled Events..........64 Viewing the Sequencer ............64 A - S ........66 PPENDIX ETUP ABLES B - L ..70 PPENDIX ATITUDE AND ONGITUDE HARTS Leviton D4200 LCD Ver 2.0 Architectural Lighting Controller...
Page 5
All manuals and user guides at all-guides.com User Guide C - M ... 79 PPENDIX ISCELLANEOUS NFORMATION Clearing the Stations Memory..........79 Leviton D4200 LCD Ver 2.0 Architectural Lighting Controller...
Indoor use only. TO AVOID FIRE, SHOCK OR DEATH: TURN OFF POWER AT MAIN CIRCUIT BREAKER OR FUSE AND TEST THAT THE POWER IS OFF BEFORE WIRING! Leviton D4200 LCD Ver 2.0 Architectural Lighting Controller Page 1 of 80...
Assign unique network ID numbers to stations. Connect one master station, and then one remote control station at a time. Verify that the first D4200 can properly control the dimmers assigned to it. Check the proper operation of each station as it is installed when multiple stations are involved.
Power Supply's for any other attached Available Unit Load control Station Quantity of Station A's attached Quantity of Station B's attached Figure 1 - Load Rating Verification Formula Leviton D4200 LCD Ver 2.0 Architectural Lighting Controller Page 3 of 80...
Page 9
NPC – DLR i-Series e Dimmer Rack Consult Factory Topaz/ENR Dimmer Rack Use DLR or NPC XP as Power Supply Power Supply Maximum Unit Loads Table 1 - Leviton D4200 LCD Ver 2.0 Architectural Lighting Controller Page 4 of 80...
Page 10
Use these quantities along with the Load Rating verification formula (Figure 1) to do the math and verify that the combined unit input load does not exceed the maximum input Unit Load Available. Leviton D4200 LCD Ver 2.0 Architectural Lighting Controller Page 5 of 80...
The maximum run length, in feet based on the total number of unit loads is shown below: Leviton D4200 LCD Ver 2.0 Architectural Lighting Controller Page 6 of 80...
The 2000 ft. limitation is a RS485 digital communications specification. The power supply pair must be sized correctly for the control stations that are connected to them. Leviton D4200 LCD Ver 2.0 Architectural Lighting Controller Page 7 of 80...
Page 13
PRESET SELECT STATION a-2000D PHASE LOSS BRIGHT FULL FULL BRIGHT SELECT SAVE COMMUNICATION PORTS AUXILIARY LUMANET CLEAR CANCEL Figure 2 - The Right and Wrong Way to Run Luma- Leviton D4200 LCD Ver 2.0 Architectural Lighting Controller Page 8 of 80...
Manufacturer Catalog Number # of Pairs Belden 9729, 9829 Belden 9841 Belden 88102 2 (Plenum Rated) Alpha 6222C Alpha 6412 Table 4- Luma-Net Recommended Wire Leviton D4200 LCD Ver 2.0 Architectural Lighting Controller Page 9 of 80...
Page 15
Blue w/ White Stripe Black White w/ Blue Stripe Orange w/ White Stripe Black White White w/ Orange Stripe Belden 9829 Belden 9729 Drain/Sheild Drain/Sheild Figure 3 - Belden Wire Callouts Leviton D4200 LCD Ver 2.0 Architectural Lighting Controller Page 10 of 80...
Step 4: small piece of heat shrink tubing. Install termination jumpers as required. Remember a Step 5: termination jumper is required at the two ends of the Luma-Net run. Leviton D4200 LCD Ver 2.0 Architectural Lighting Controller Page 11 of 80...
Page 17
A2000-D FULL BRIGHT PHASE LOSS FULL BRIGHT SELECT SAVE COMMUNICATION PORTS AUXILIARY CANCEL LUMANET CLEAR Ground Shield only! at one point Figure 5 - Luma-Net Termination Jumper Locations Leviton D4200 LCD Ver 2.0 Architectural Lighting Controller Page 12 of 80...
Test the following wire pairs for shorts at each station Step 1: location, using an ohmmeter or other continuity tester. 1-2 Open 2-3 Open 3-4 Open Repair any short circuits before continuing. Step 2: Leviton D4200 LCD Ver 2.0 Architectural Lighting Controller Page 13 of 80...
Install the Unit to the Wall Remove faceplate. Step 1: Insert wired phoenix connector into D4200 unit, per Figure Step 2: Leviton D4200 LCD Ver 2.0 Architectural Lighting Controller Page 14 of 80...
Page 20
Mount Controller in 4-gang, gang box (10 in. wide, 2 Step 3: in deep) with 4-gang device cover (10 in. wide, in. or in. deep) as per Figure 8. Leviton D4200 LCD Ver 2.0 Architectural Lighting Controller Page 15 of 80...
Page 21
Figure 8 - Mounting Illustration Carefully position all wires to provide room in gang box for Step 4: D4200 LCD station. Mount the D4200 to raised cover using the screws provided. Be careful and do not overtighten the screws. See Figure 8.
Note: You need to set a unique number from 001 to 127 for it to function. Press the Select/Save button to save the values. Step 2: MAIN MENU MANUAL MODE M18 MON 12:00P Leviton D4200 LCD Ver 2.0 Architectural Lighting Controller Page 17 of 80...
Your version number should be the same or greater than this manual. You are now ready to proceed with Initial Setup and Programming. Leviton D4200 LCD Ver 2.0 Architectural Lighting Controller Page 18 of 80...
The Programming and Configuration Level Menus is used for the following features: • Assign Zones • Edit Network Network ID • Change Personalities • Miscellaneous Settings: Flags Setup Astronomical Time Set the Maximum number of Zones Leviton D4200 LCD Ver 2.0 Architectural Lighting Controller Page 19 of 80...
SET RECORD LOCK SET STATION LOCK MENU SET RECORD SET STATION MENU LOCK CODE=000 STATION LOCK=ON LOCK CODE=000 RECORD LOCK=ON Figure 9 - LCD Screen Shots of Main Menu Leviton D4200 LCD Ver 2.0 Architectural Lighting Controller Page 20 of 80...
MISC. SETTINGS: SUNSET=00:00 MISC. SETTINGS: WEEK=XX MISC. SETTINGS: MIDNIGHT=12:00 MISC. SETTINGS: SR=06:04SS=17:56 MISC. SETTINGS: MAX ZONES=32 Figure 10 - LCD Screen Shots of Programming and Configuration Level Menu’s Leviton D4200 LCD Ver 2.0 Architectural Lighting Controller Page 21 of 80...
Page 27
Union or Off) Record Lock: ON or OFF Station Lock: ON or OFF Record Lock Code: (Default-000) Station Lock Code: (Default-000) Table 6 - User Setting’s for Easy Setup Leviton D4200 LCD Ver 2.0 Architectural Lighting Controller Page 22 of 80...
P2 = Zones 9-16 P3 = Zones 17-24 Breakfast P4 = Zones 25-32 S01 TUE 04:29p LE Indicates Schedule is active Indicates Station is Locked Days of week Scene # Leviton D4200 LCD Ver 2.0 Architectural Lighting Controller Page 23 of 80...
Press the Menu button to access the Advanced features Step 4: that have been added to the menu. When you are finished using the Setup menu selections, be sure to return to the regular menu. Leviton D4200 LCD Ver 2.0 Architectural Lighting Controller Page 24 of 80...
LEVITON appears on the LCD display. Wait until the LCD display changes to MANUAL MODE. Step 2: Operate the buttons on the D4200 one at a time. Pressing two or more buttons at once may not yield the desired result.
Page 31
The Network ID number flashes. Press the Up and Down buttons to change the Step 5: value. You need to set a unique number from 001 to 127 for it to function. Leviton D4200 LCD Ver 2.0 Architectural Lighting Controller Page 26 of 80...
Again, if the “REMOTE TO=xxx” field is 000, the unit is a “master”. Note: “Remote” Entry stations also have two net IDs, their Network ID and their master’s Net ID, otherwise known as their “REMOTE TO” or “TARGET” ID. Leviton D4200 LCD Ver 2.0 Architectural Lighting Controller Page 27 of 80...
04. The default setting is generally satisfactory for most simple installations with one or two D4200 controls and one dimmer cabinet. Setting START CHANN to a number causes all zones to be assigned to sequential channel numbers starting with that same number and adding one to each zone there after.
The following list of individually setable option flags. Use lower ” case to indicate the to indicate the feature is ON, and use “ feature is OFF. By default these options are all OFF (lower case) Leviton D4200 LCD Ver 2.0 Architectural Lighting Controller Page 29 of 80...
Page 35
LCD station is upgraded to new code, but the entry stations are not. • IR Control: Allows the user to select if the IR port is active or disabled. On indicates that the IR port is active. Leviton D4200 LCD Ver 2.0 Architectural Lighting Controller Page 30 of 80...
The first one is the dimmer “Readback. If it is “lower” case the option is OFF. If it is “UPPER” case the option is ON. Leviton D4200 LCD Ver 2.0 Architectural Lighting Controller Page 31 of 80...
Press the Select/Save button. Step 6: The Dimmer Readback value flashes. Press the Right button to move to the next field. Step 7: The Double Bump value flashes. Leviton D4200 LCD Ver 2.0 Architectural Lighting Controller Page 32 of 80...
1.3 - Setting the LCD Backlight Time Out Flag This flag allows the backlight on the LCD to turn off after 60 seconds of no button presses on the D4200 station. To enable this feature: Access the Programming and Configuration Level menu Step 1: Press the Menu/Cancel button.
Step 10: 1.4 - Setting the Time Master Flag This flag allows this D4200 station to take over as the Time Master. In this mode, a Time Master is the unit on the network that emits the time of day / date settings every 60 seconds. This helps all products that use the time / date information to stay synchronized.
Step 10: 1.5 - Previous Code Compatibility This flag allows this D4200 station to work with units that have previous code installed on them. This usually occurs when a LCD station is upgraded to new code, but the entry stations are not. For installs where only the 2.xx code resides, you want to make sure that...
Step 10: 2 - Setting up the Astronomical Clock The D4200 allows you to turn lights on or off in relation to sunrise and sunset. For example, yard lights can be set to turn on an hour before sunset, and turn off an hour after sunrise, according to the time of year.
Page 42
Press the Right button to move to the minute field. Step 10: The minute value flashes. Press the Up and Down buttons to set the Step 11: minutes. Leviton D4200 LCD Ver 2.0 Architectural Lighting Controller Page 37 of 80...
24 Zones: “P1-P3” is displayed by the top right 2 Step 3: characters, indicating zones 1 to 8, 9 to 16 or 17-24 are being displayed. When you reach “P3” the Zone number Leviton D4200 LCD Ver 2.0 Architectural Lighting Controller Page 38 of 80...
(choir performance) set of Scenes could be recorded without disturbing the normal Sunday church service settings. The following information will need to be re-entered for each personality: Leviton D4200 LCD Ver 2.0 Architectural Lighting Controller Page 39 of 80...
Test each station by raising and lowering each zone that is assigned to a dimmer. Check to see that control of the dimmer cabinet or other control device is correct and smooth. Main Level Menus Leviton D4200 LCD Ver 2.0 Architectural Lighting Controller Page 40 of 80...
All manuals and user guides at all-guides.com User Guide Scheduling The D4200 is already programmed to accept up to 64 possible Events, numbered E01 through E64. The default values are 12:00a (12:00 am), NONE (no Scene), and SMTWTFS (all days of the week).
Page 47
Repeat this process for all 7 days. Press the Select/Save button to save these values for Step 15: the Event. The Event number flashes again. Leviton D4200 LCD Ver 2.0 Architectural Lighting Controller Page 42 of 80...
(GOTO a specific step). There is a table provided in Appendix A to help you set up the sequencer schedule. Leviton D4200 LCD Ver 2.0 Architectural Lighting Controller Page 43 of 80...
Note: Press Clear to change the value to SKIP . • STOP • LOOP • GOTO _ _ • SKIP • Scene (With Delay Time) • MAX • OFF Leviton D4200 LCD Ver 2.0 Architectural Lighting Controller Page 44 of 80...
Zone Labels: Naming a Scene or Zone You can program alphanumeric labels with up to 14 characters for any Scene MAX, OFF or Zone ID buttons. To name a Scene or a Zone: Leviton D4200 LCD Ver 2.0 Architectural Lighting Controller Page 45 of 80...
Page 51
Master Master Space Page Page Zones Zones Figure 12 - Shortcut for Alpha Keys Press the Select/Save button to save the value and edit Step 7: the label. Leviton D4200 LCD Ver 2.0 Architectural Lighting Controller Page 46 of 80...
1 is zones 1 to 8, page 2 is zones 9 to 16, page 3 is zones 17 to 24, page 4 is zones 25 to 32. Use Clear to clear all “excludes” i.e. to include all zones. By default all zones are included. Leviton D4200 LCD Ver 2.0 Architectural Lighting Controller Page 47 of 80...
Press the Menu/Cancel button to exit this menu. Step 7: Setting the date and time will set date and time on all other stations on the same lighting control network (using the Luma-Net™ data protocol). Leviton D4200 LCD Ver 2.0 Architectural Lighting Controller Page 48 of 80...
Press the Select/Save button again. Step 4: Press the Up and Down buttons until your Step 5: choice is flashing. Press the Select/Save button to record the change. Step 6: Leviton D4200 LCD Ver 2.0 Architectural Lighting Controller Page 49 of 80...
Step 1: Press the Up and Down buttons until SET Step 2: RECORD LOCK? flashes on the LCD display. Press the Select/Save button. Step 3: The CODE field flashes Leviton D4200 LCD Ver 2.0 Architectural Lighting Controller Page 50 of 80...
Step 6: Press the Menu/Cancel button to exit this menu. Step 7: Enabling the Record Lock Be sure to set the Record Lock code before enabling the Record Lock. Leviton D4200 LCD Ver 2.0 Architectural Lighting Controller Page 51 of 80...
Press Clear to change the value to OFF . Press the Select/Save button to save the value. Step 5: flashes again. STATION LOCK= Press the Menu/Cancel button to exit this menu. Step 6: Leviton D4200 LCD Ver 2.0 Architectural Lighting Controller Page 52 of 80...
“Pass Code” to override this lock. Congratulations: Your D4200 LCD Station is completely set up and ready for use. Leviton D4200 LCD Ver 2.0 Architectural Lighting Controller Page 53 of 80...
Scene fades out. Tapping a Scene button twice (if enabled) causes the lighting levels to change Leviton D4200 LCD Ver 2.0 Architectural Lighting Controller Page 54 of 80...
Page 60
Programming or Recall All Off Select Option and Save Change Zone All Zones to IR Receiver Maximum Brightness Menu and Clear Cancel Button Figure 15 - D4200 Buttons Leviton D4200 LCD Ver 2.0 Architectural Lighting Controller Page 55 of 80...
Page 61
All manuals and user guides at all-guides.com User Guide Operate the buttons on the D4200 one at a time. If you activate the station lock code or the station lockout switch, the Master Up/Down, Zone Up/Down, SCENE, MAX, and OFF buttons are disabled until a code is entered or the lockout switch is deactivated (see Overriding a Lock ).
The OFF button can be modified from the default value of Changing the MAX and OFF Lighting no light (see Levels ). Leviton D4200 LCD Ver 2.0 Architectural Lighting Controller Page 57 of 80...
Page 63
Zones when you press the Master Up Down buttons. As each Zone reaches its maximum or minimum level, it stays at that level while the other Zones catch up. Leviton D4200 LCD Ver 2.0 Architectural Lighting Controller Page 58 of 80...
MANUAL MODE after any Zone Up or Down button is pressed. You can record these new values for the Scene if you prefer the new lighting levels. Leviton D4200 LCD Ver 2.0 Architectural Lighting Controller Page 59 of 80...
Just to the right of the “Zxx:” symbol on the 2nd line is a field that is normally blank. If this Zone is excluded from the current scene, a minus sign (“-”) appears in this position. Leviton D4200 LCD Ver 2.0 Architectural Lighting Controller Page 60 of 80...
Press the Select/Save button to record the lighting levels Step 5: and fade time. The LCD display shows RECORDING SCENE TO S00 , with representing the Scene you chose. Leviton D4200 LCD Ver 2.0 Architectural Lighting Controller Page 61 of 80...
Press the Select/Save button to record the lighting levels Step 5: and fade time. The LCD display shows RECORDING SCENE TO S00 , with representing the Scene you chose. Leviton D4200 LCD Ver 2.0 Architectural Lighting Controller Page 62 of 80...
Master RAISE/ LOWER, SCENE, MAX and OFF buttons in the same manner as indicated above. The maximum range for the remote control is approximately 30 feet. Leviton D4200 LCD Ver 2.0 Architectural Lighting Controller Page 63 of 80...
The sequencer causes Scenes to be activated in a timed sequence. The sequence may be programmed to run once or continuously in a loop. The sequence can be activated manually (preset/scene buttons) Leviton D4200 LCD Ver 2.0 Architectural Lighting Controller Page 64 of 80...
Page 70
LOOP Press the Up and Down buttons to scan Step 4: through the possible Events. Press the Menu/Cancel button to exit this menu. Step 5: Leviton D4200 LCD Ver 2.0 Architectural Lighting Controller Page 65 of 80...
All manuals and user guides at all-guides.com User Guide Appendix A - Tables Zone Zone Label Luma-Net Channel Table - A1 - Zone Labels and Dimmer Channels Form Leviton D4200 LCD Ver 2.0 Architectural Lighting Controller Page 66 of 80...
Page 72
All manuals and user guides at all-guides.com User Guide Scene Scene Label Zones Excluded from Scene Accessible from LCD Station: Accessible from Entry Station: Table A2 - Scene Labels and Zone Exclusions Form Leviton D4200 LCD Ver 2.0 Architectural Lighting Controller Page 67 of 80...
Page 73
E vent # S M T W T F S R esum e, C ell O n, Seq. # ) T im e Table A3 - Scheduling Form Leviton D4200 LCD Ver 2.0 Architectural Lighting Controller Page 68 of 80...
Page 74
Skip, Goto Step, Loop, Stop, Sequencer Sequencer Loop, Stop, Off and Delay, Off and Delay, Max and Event # Event # Max and Delay Delay) Table A4 - Sequencer Form Leviton D4200 LCD Ver 2.0 Architectural Lighting Controller Page 69 of 80...
92° W San Francisco Co 38° N 122° W Pine Bluff AP 34° N 92° W San Jose AP 37° N 122° W Texarkana AP 33° N 94° W Leviton D4200 LCD Ver 2.0 Architectural Lighting Controller Page 70 of 80...
Page 76
21° N 158° W Andrews AFB 38° N 76° W Kaneohe Bay MCAS 21° N 158° W Washington, National AP 39° N 77° W Wahiawa 21° N 158° W Leviton D4200 LCD Ver 2.0 Architectural Lighting Controller Page 71 of 80...
Page 77
101° W Fort Wayne AP 41° N 85° W Goshen AP 42° N 86° W Manhattan, Ft Riley (S) 39° N 97° W Parsons 37° N 96° W Leviton D4200 LCD Ver 2.0 Architectural Lighting Controller Page 72 of 80...
Page 78
93° W Salisbury (S) 38° N 75° W Mankato 44° N 93° W Minneapolis/St. Paul AP 45° N 94° W Rochester AP 44° N 92° W State/City Lat. Long. Leviton D4200 LCD Ver 2.0 Architectural Lighting Controller Page 73 of 80...
Page 79
New Brunswick 40° N 74° W Great Falls AP (S) 47° N 111° W Paterson 41° N 74° W Havre 49° N 110° W Phillipsburg 41° N 75° W Leviton D4200 LCD Ver 2.0 Architectural Lighting Controller Page 74 of 80...
Page 80
39° N 85° W Oneonta 43° N 75° W Cleveland AP (S) 41° N 82° W Oswego Co 43° N 77° W Columbus AP (S) 40° N 83° W Leviton D4200 LCD Ver 2.0 Architectural Lighting Controller Page 75 of 80...
Page 81
81° W Grants Pass 42° N 123° W Spartanburg AP 35° N 82° W Klamath Falls AP 42° N 122° W Sumter, Shaw AFB 34° N 80° W Leviton D4200 LCD Ver 2.0 Architectural Lighting Controller Page 76 of 80...
Page 82
79° W Greenville 33° N 96° W Fredericksburg 38° N 77° W Harlingen 26° N 98° W Harrisonburg 38° N 79° W Lynchburg AP 37° N 79° W Leviton D4200 LCD Ver 2.0 Architectural Lighting Controller Page 77 of 80...
Page 83
88° W Green Bay AP 44° N 88° W La Crosse AP 44° N 91° W Madison AP (S) 43° N 89° W Manitowoc 44° N 87° W Leviton D4200 LCD Ver 2.0 Architectural Lighting Controller Page 78 of 80...
Page 84
Press and hold the Master Down button until the LCD display shows INITIALIZING DEFAULTS. Once LEVITON appears on the LCD display, the memory is reset to the factory default values. Leviton D4200 LCD Ver 2.0 Architectural Lighting Controller Page 79 of 80...
Page 85
F.O.B. factory. Leviton is not responsible for removing or replacing equipment on the job site, and will not honor charges for such work. Leviton will not be responsible for any loss of use time or subsequent damages should any of the...
Page 86
All manuals and user guides at all-guides.com NOTES:...
Page 87
All manuals and user guides at all-guides.com NOTES:...