Owon VDS Series Quick Manual

Owon VDS Series Quick Manual

Pc oscilloscopes
Hide thumbs Also See for VDS Series:

Advertisement

General Warranty
OWON warrants that the product will be free from defects in materials and
workmanship for a period of 3 years from the date of purchase of the product by
the original purchaser from the OWON Company. The warranty period of
accessories such as probe is 12 months. This warranty only applies to the original
purchaser and is not transferable to the third party.
If the product proves defective during the warranty period, OWON either will repair
the defective product without charge for parts and labor, or will provide a
replacement in exchange for the defective product. Parts, modules and
replacement products used by OWON for warranty work may be new or
reconditioned like new performance. All replaced parts, modules and products
become the property of OWON.
In order to obtain service under this warranty, customer must notify OWON of the
defect before the expiration of the warranty period. Customer shall be responsible
for packaging and shipping the defective product to the service center designated
by OWON, and with a copy of customer proof of purchase.
This warranty shall not apply to any defect, failure or damage caused by improper
use or improper or inadequate maintenance and care. OWON shall not be
obligated to furnish service under this warranty a) to repair damage resulting from
attempts by personnel other than OWON representatives to install, repair or
service the product; b) to repair damage resulting from improper use or connection
to incompatible equipment; c) to repair any damage or malfunction caused by the
use of non-OWON supplies; or d) to service a product that has been modified or
integrated with other products when the effect of such modification or integration
increases the time or difficulty of servicing the product.
Please contact the nearest OWON's Sales and Service Offices for services or a
complete copy of the warranty statement.
For better after-sales service, please visit
www.owon.com.cn
and register the
purchased product online.
Excepting the after-sales services provided in this summary or the applicable warranty
statements, OWON will not offer any guarantee for maintenance definitely declared or
hinted, including but not limited to the implied guarantee for marketability and
special-purpose acceptability. OWON should not take any responsibilities for any
indirect, special or consequent damages.
For more detailed information, please see the help document of the software, you
can open it by pressing F1 in the window of software.

Advertisement

Table of Contents
loading

Summary of Contents for Owon VDS Series

  • Page 1 product.
  • Page 2: Table Of Contents

    Table of Contents 1. General Safety Requirements ..................1 2. Safety Terms and Symbols ....................2 3. Ports Introduction ......................5 VDS1022(I) ........................... 5 VDS2062(L) / VDS3102(L) ......................6 VDS2064(L) / VDS3104(L) ......................7 4. How to Implement the General Inspection ..............8 5.
  • Page 3: General Safety Requirements

    1. General Safety Requirements Before any operations, please read the following safety precautions to avoid any possible bodily injury and prevent this product or any other products connected from damage. In order to avoid any contingent danger, this product is only used within the range specified. Only the qualified technicians can implement the maintenance.
  • Page 4: Safety Terms And Symbols

    2. Safety Terms and Symbols Safety Terms Terms in this manual. The following terms may appear in this manual: Warning: Warning indicates the conditions or practices that could result in injury or loss of life. Caution: Caution indicates the conditions or practices that could result in damage to this product or other property.
  • Page 5 (30Vrms) or on circuits of more than 4800VA: Use only insulated probes and adapter supplied with the test tool, or indicated by OWON as suitable for the Oscilloscope. Before use, inspect probes and accessories for mechanical damage and replace when damaged.
  • Page 6 Do not apply voltages that differ more than 40 V from earth ground to any non-isolated inputs when measuring in a CAT environment. Do not apply voltages that differ more than 40 V from each other to the non-isolated inputs when measuring in a CAT environment.
  • Page 7: Ports Introduction

    3. Ports Introduction VDS1022(I) Figure 3-1 Ports of the Oscilloscope 1. USB port: Supply power by PC USB or the adapter; communicate with PC 2. Probe Compensation: Measurement signal (3.3 V / 1 kHz) output 3. MULTI port: EXT trigger input, trigger output or Pass/Fail output 4.
  • Page 8: Vds2062(L) / Vds3102(L)

    VDS2062(L) / VDS3102(L) Figure 3-2 Ports of the Oscilloscope (take VDS3102(L) for instance) 1. USB port: Supply power by PC USB or the adapter; communicate with PC 2. LAN port (optional): Network port which can be used to connect with PC 3.
  • Page 9: Vds2064(L) / Vds3104(L)

    VDS2064(L) / VDS3104(L) Figure 3-3 Ports of the Oscilloscope (take VDS3104(L) for instance) 1. Probe Compensation: Measurement signal (3.3 V/1 kHz) output 2. MULTI Connector (optional): Connect Q9 cable with the MULTI port 3. MULTI port: EXT trigger input, trigger output or Pass/Fail output 4.
  • Page 10: How To Implement The General Inspection

    4. How to Implement the General Inspection After you get a new VDS series oscilloscope, it is recommended that you should make a check on the instrument according to the following steps: 1. Check whether there is any damage caused by transportation.
  • Page 11: How To Implement The Function Inspection

    6. How to Implement the Function Inspection Make a fast function check to verify the normal operation of the instrument. First, connect the oscilloscope with PC successfully, and then do the following steps: Click in the software interface to restore to factory settings. The default attenuation coefficient set value of the probe in the software is 10X.
  • Page 12: How To Use The Probe Safely

    2. Check the displayed waveforms and regulate the probe till a correct compensation is achieved (see Figure 7-2 and Figure 7-3). Overcompensated Compensated correctly Under compensated Figure 7-2 Displayed Waveforms of the Probe Compensation 3. Repeat the steps mentioned if needed. Figure 7-3 Adjust Probe 8.
  • Page 13: Appendix

    9. Appendix Appendix A: Enclosure Standard Accessories: Passive probe: 1.2 m, 1:1 (10:1) (2 for dual-channel, 4 for four-channel) 1x CD (Supplied Software) 1x USB cable 1x Quick Guide 1x AC-DC adapter (only for the model with LAN port) Options: 1x Soft case Appendix B: General Care and Cleaning General Care...
  • Page 14 VDS Series PC Oscilloscopes Technical Specifications Note: "I" indicates the model has the power supply isolation and earth ground isolation between the oscilloscope and PC (optional), the two channels are non-isolated electrically. "L" indicates LAN port (optional). Model Bandwidth Sample rate...
  • Page 15 Edge, Video, Slope, Pulse, Alternate Trigger type Auto, Normal, Single Trigger mode Line/field Support standard NTSC, PAL and SECAM broadcast systems frequency (Video) Vpp, Vmax, Vmin, Vtop, Vbase, Vamp, Vavg, Vrms, Overshoot, Preshoot, Automatic , +Width, measurement -Width, +Duty, -Duty Waveform Math , ×, ÷, FFT VDS1022(I)

Table of Contents