Download Print this page

Fujitsu ScanPartner 15C User Manual

Image scanner
Hide thumbs

Advertisement

Quick Links

Scanpartner 15C
Image Scanner
User's Manual
Version 1.0
(Doc. No. 250-0062-0)

Advertisement

loading

  Summary of Contents for Fujitsu ScanPartner 15C

  • Page 1 Scanpartner 15C Image Scanner User's Manual Version 1.0 (Doc. No. 250-0062-0)
  • Page 2: Table Of Contents

    Table of Contents 1. INTRODUCTION ... 1-1 2. INSTALLATION AND CONNECTIONS ... 2-1 2.1 S ... 2-1 HIPPING RACKET 2.1.1 Removing the Shipping Bracket (refer to figures 2-1 and 2-2) ... 2-1 2.1.2 Refitting the Shipping Bracket: ... 2-3 2.2 SCSI I ID ...
  • Page 3: Introduction

    INTRODUCTION Congratulations on your purchase of Fujitsu Scanpartner 15C Scanner. Before you install and operate the new Scanner, please take a few minutes to read through this manual. It provides you with the proper instructions on how to unpack, install, operate and maintain the Scanner.
  • Page 4 Output Paper Rack Figure 1-1 Scanner packing...
  • Page 5: Installation And Connections

    Precautions Keep the Scanner out of direct sunlight. Direct exposure to the sun or excessive heat may cause damage to the unit. Do not install the Scanner in a humid or dusty place.
  • Page 6 Figure 2-1 Removing the Shipping Bracket Figure 2-2 Securing the Shipping Bracket...
  • Page 7: Refitting The Shipping Bracket

    ID. (See Figure 2-3) Note: The factory setting for Scanner is ID 6. Usually, ID 0 is assigned to an internal hard disk drive, and ID 7, to SCSI adapter or host. ID 8 and 9 are not in actual use.
  • Page 8 SCSI ID Selector Figure 2-3 Adjusting the SCSI ID setting.
  • Page 9: Adf Paper Chute (Figure 2-4)

    2.3 ADF Paper Chute (Figure 2-4) Raise the right side of the paper chute to about 45 degrees. ii). Pull down the wire leg from under the paper chute. iii). Insert the wire leg into the grips on the document cover. iv).
  • Page 10: Adf Output Tray (Figure 2-5)

    2.4 ADF Output Tray (Figure 2-5) Hold the output paper rack some 30 degrees aslant as shown in Figure 2-5. ii). Insert the three protrusions on the output paper tray to the three slots on the ADF. iii). Release the paper tray gently. Make sure the tray is firmly attached to the ADF. iv).
  • Page 11: Document Loading

    Refer to Figure 2-6) i). Place the document to be scanned onto the document glass face down. ii). Position the document so that the upper-right corner is aligned with the reference mark. Figure 2-6- Place Document on the Scanner...
  • Page 12: Adf Scanning

    2.6 ADF Scanning Standard paper size can be scanned automatically using the ADF. Refer to figure 2-7. To prevent occasional paper jam when automatically feeding multiple documents, fan the paper before loading. ii). Lift the balance wire and place the documents to be scanned onto the ADF paper chute face down, with the leading edge in the auto feeder entrance.
  • Page 13: Connecting The Cable

    SCSI Termination The Fujitsu Scanpartner 15C comes complete with a built in SCSI terminator. If the Scanner is the last device in a SCSI chain the terminator should be switched on. If the Scanner is not the last device the terminator should be off. The terminator on/off switch is located on the back of the Scanner, to the left of the SCSI cable connectors.
  • Page 14 SCSI Cable Figure 2-8 Scanpartner 15C Scanner Cable Connection Figure 2-9 Scanpartner 15C SCSI Scanner Cable Connections with Mac 2-10...
  • Page 15: Maintenance

    3. MAINTENANCE 3.1 Cleaning the ADF Your Scanner is designed to be maintenance free. However, it still needs to be cleaned occasionally to ensure optimum image quality and performance. From time to time the pad assembly and feeding rollers may become contaminated with ink, toner particles or paper dust.
  • Page 16 Figure 3-1 Opening the ADF unit and Document Cover...
  • Page 17: Cleaning The Glass

    Open the ADF unit and document cover as shown in Figure 6-2. Wipe the glass of flatbed area and ADF area by moving the swab from side to side. iii). Close the ADF unit and document cover. Your Scanner is now ready for use. Figure 3-2 The Cleaning Area...
  • Page 18: Troubleshooting

    Scanner by turning it off and then on again, reboot your host computer as well. b) Check if the driver is correctly installed. You DIAG.EXE file in “Fujitsu Driver Kit” to check this out. c) Try to select another port memory. Question: Paper becomes jammed during scanning.
  • Page 19 5000 hours. b) The fuse on main board of the Scanner is burned. Check the main board of the Scanner. If the fuse is burned, put in a new fuse that is 250V/2A. c) If the fuse burns again after the changing, it means the invertor of the lamp is burned.
  • Page 20: Paper Jam In The Adf

    4.2 Paper Jam in the ADF In the event of paper jam, please follow the procedures below. i). Press the button at the front left of the Scanner as shown in Figure 4-1, arrow A. The ADF cover will be released.
  • Page 21 Figure 4.2 ADF Paper Jam - Removing the Paper...
  • Page 22: Specifications

    5. SPECIFICATIONS All specifications are subject to change without notice. The following can not be properly fed by ADF: Paper with clip or staple attached; Paper with ink not totally dry; Paper with inconsistent thickness, such as envelopes; Paper with wrinkles, curls, folds or tears; Tracing paper;...
  • Page 23: Scanpartner 15C Specifications

    5.1 Scanpartner 15C Specifications Scanner Type Scanning Mode Optical Resolution Light Source ADF Capacity ADF Scanning Speed Scanning Document Size Max. Interface Power Requirement Power Consumption Humidity Operation Temperature Storage Temperature Dimension Weight 1-pass colour Flatbed with ADF built-in 30-bit colour...