GrowSpan 115020 Manual
  1. Manuals
  2. Brands
  3. GrowSpan Manuals
  4. Greenhouse Kit
  5. 115020
  6. Manual

GrowSpan 115020 Manual

Single swinging door – black-out door kit
Hide thumbs
1
2
3
4
5
6
7
8
9
Table of Contents

Advertisement

Quick Links

Download this manual
Single Swinging Door – Black-Out Door Kit
Ground Level
ATTENTION: Door kit includes materials for door only. All other components shown in the diagram above
and diagrams throughout this guide are not included and require additional purchase. Actual building may
differ from examples shown throughout this guide.
©2020 GrowSpan™
All Rights Reserved. Reproduction
is prohibited without permission.
Revision date: 01.28.20
GrowSpan
™
STK#
115020 (Twin-Wall Polycarbonate)
1

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the 115020 and is the answer not in the manual?

Questions and answers

Related Manuals for GrowSpan 115020

Summary of Contents for GrowSpan 115020

  • Page 1 ATTENTION: Door kit includes materials for door only. All other components shown in the diagram above and diagrams throughout this guide are not included and require additional purchase. Actual building may differ from examples shown throughout this guide. ©2020 GrowSpan™ All Rights Reserved. Reproduction is prohibited without permission. STK# 115020 (Twin-Wall Polycarbonate) Revision date: 01.28.20...

  • Page 2: Required Tools

    READ THIS DOCUMENT BEFORE YOU BEGIN • Variable speed drill and impact driver (cordless with extra batteries works best) Thank you for purchasing this GrowSpan™ door kit. When properly assembled and maintained, this product • Tool to cut polycarbonate panel will provide years of reliable service.

  • Page 3: Parts Identification

    Important Information IMPORTANT NOTICE: Remove protective film from the SINGLE SWINGING DOOR KIT: READ THIS BEFORE polycarbonate panel. Allowing film to remain intact and YOU BEGIN in direct sunlight will make it difficult if not impossible to remove. Store panel out of direct sunlight until film is Consult the services of a qualified contractor if needed.
  • Page 4 Door Frame Assembly ASSEMBLE DOOR FRAME COMPONENTS Cut along dotted lines. Consult diagrams near the back of this guide before you begin. Remove this section ATTENTION: Photos and diagrams show attaching door frame to an end wall constructed using girts with a specific profile. If actual end wall frame differs, take necessary steps to alter instructions as needed to allow proper installation of door jambs and header.

  • Page 5: Top View

    Door Frame Assembly ASSEMBLE DOOR FRAME COMPONENTS (continued) 5. With door jambs attached, measure and mark height of rough door opening. Consult drawing below and Door Frame Layout located in Quick Start. Measure from finished grade to underside of header. Bend this 6.
  • Page 6 Twin-Wall Single Swinging Door SINGLE TWIN-WALL DOOR ASSEMBLY 6. Install aluminum U-channel profile along all pannel edges. Ends can be mitered or cut as shown. Materials and parts needed to assemble the 115020 door include: • Door frame (102923), 8mm panel (113296Z096), door hinges (FA5030), and latch (FA2410) •...
  • Page 7 Twin-Wall Single Swinging Door SINGLE TWIN-WALL DOOR ASSEMBLY (continued) 13. With assistance, set assembled door in door frame and secure hinges to door jamb using one Tek screw 10. Mark plate mounting hole locations on panel and drill per hinge at this time. a 5/16"...
  • Page 8 Quick Start Guide QUICK START GUIDE Single Swinging Door Kit Twin-Wall Door Sample 115020 Ground Level ATTENTION: End frame and end rafter are not included with any door kit. These are presented to demonstrate installation. Revision date: 01.28.20...
  • Page 9 Revision date: 01.28.20...

Table of Contents