Table of Contents
Advertisement
Quick Links
Installation, Operating and Servicing
Instructions
Phoenix Twin Zone Induction Hob
PHEH01
Please make a note of your product details for
future use:
Date Purchased:_________________________
Model Number:__________________________
Serial Number:__________________________
Dealer:_________________________________
_______________________________________
IS707 ECN 4277
1
Advertisement
Table of Contents
Related Manuals for Lincat PHEH01
Summary of Contents for Lincat PHEH01
- Page 1 Installation, Operating and Servicing Instructions Phoenix Twin Zone Induction Hob PHEH01 Please make a note of your product details for future use: Date Purchased:_________________________ Model Number:__________________________ Serial Number:__________________________ Dealer:_________________________________ _______________________________________ IS707 ECN 4277...
-
Page 2: Table Of Contents
WARNING! This symbol is used whenever there is a risk of personal injury. CAUTION! This symbol is used whenever there is a risk of damaging your Lincat product. NOTE: This symbol is used to provide additional information, hints and tips. -
Page 3: Warnings And Precautions
250v) The ceramic glass is very strong but do not slam pans down onto it and be careful not to scrape pans along the surface. TECHNICAL DATA PHEH01 Width (mm) Depth (mm) Hob height (mm) Cooking area w x d (mm) -
Page 4: Checklist Of Enclosures
CHECK LIST OF ENCLOSURES Warranty card Instructions manual INSTALLATION AND COMMISSIONING This appliance must be earthed. If replacing the plug connect the terminals as follows: Green and Yellow wire Earth Blue wire Neutral N Brown wire Live Supply cords shall be oil resistant, sheathed flexible cable not lighter than ordinary polychloroprene or equivalent elastomer sheathed cord (code 60245 IEC 57) Install this appliance on a level surface ensuring all vents are unobstructed. -
Page 5: Operating Instructions
Power Ratings Model Amps Supply PHEH01 16.0 Heat input rear zone, normal 1.85 Heat input rear zone, boost 13.0... - Page 6 The quality of the cookware is important to the efficiency of induction cooking. The pan base must be flat with good heat distribution. Suitable pans are made from cast iron, enamelled steel and stainless steel with a magnetic base. Unsuitable pans are glass, earthenware, aluminium, copper and non-magnetic stainless steel.
- Page 7 Hob control settings Constantly variable power level settings are available via the rotary control knob. There are a number of features available to you to enhance your appliances productivity. The following symbols are observed through the ceramic glass: Low temperature hold Power level setting (1-9) Power boost function Automatic heat up control...
- Page 8 Power level settings 9 power level settings are available. The table gives the percentage of maximum power for each setting with the time limit for operation at that power. Power level Low temp hold % of power 15% 19% 31% 45% 64% 100% Time limit (mins) Power boost function Power boost is activated by turning the control clockwise from level 9.
- Page 9 There are numerous ‘E’ symbol error codes identifying issues within the system which are primarily of use when reporting a fault to the Service Department at Lincat. Some errors can be cleared by turning the control off, or completely turning off and unplugging the appliance before reconnecting.
-
Page 10: Cleaning
CLEANING Isolate from the power supply and allow to cool. Do not use a water jet or steam cleaner, and do not immerse this appliance. Clean all panels with warm water and mild detergent, do not use abrasive materials. Do not wet electrical components. Dry with a soft cloth. Clean the ceramic glass with a scraper or Vileda CERAN cleaning sponge –... -
Page 11: Servicing, Maintenance And Component Replacement
SERVICING, MAINTENANCE AND COMPONENT REPLACEMENT Replacement of air filter Cool the appliance and disconnect from supply. Turn the hob on its back or side without scratching the cooking surface. Push the slide latch (Fig 3) and lift the filter cover away from the base. Replace the used filter with a new one. -
Page 12: Fault Finding
FAULT FINDING Please refer to the Service Help Desk number on the final page of this manual. SPARE PARTS LIST Part Number Description FE10 Foot FG03 Fanguard FI33 Filter pad KN523 Control knob NE43 Neon S/R0079 Cooling fan IS 781 ECN 4833 Page 12 of 13... -
Page 13: Service Information And Guarantee
All available on serial plate Type number Serial number Lincat reserve the right to carry out any work under warranty, given reasonable access to the appliance, during normal working hours, Monday to Friday, 08:30 to 17:00. GUARANTEE This unit carries a comprehensive UK mainland 2 year warranty. The guarantee is in addition to, and does not diminish your statutory or legal rights.