Table of Contents
Advertisement
Quick Links
CSM(I)QMTDC-163-1-SG-RPR/RPL
QMT® Shade Motor Replacement, Battery Operated
Use the Crestron® CSM(I)-QMTDC-163-SG-RPR/RPL QMT® shade motor
to replace an existing motor.
In the Box
1
CSM(I)-QMTDC-163-1-SG, Replacement Motor
Motor Replacement
CAUTION: Roll up the shade fabric to prevent damage during this
procedure.
NOTES:
A soft and clean work surface is required to perform this
l
procedure.
Remove the fascia and disconnect the motor cable before
l
performing this procedure.
Remove the Roller Shade Assembly from the
Mounting Brackets
CAUTION: Roll up the shade fabric to prevent damage during this
procedure.
Remove the roller shade assembly from the brackets:
NOTE: Place the roller shade on a soft and clean surface where it will
not be damaged.
1. If the fascia is installed, remove the fascia.
2. To disconnect the old QMT shade motor from the motor mounting
bracket, press the release button on the bottom of the shade motor.
3. Push the roller shade assembly toward the idler bracket; the idler pin
compresses to allow the motor end to swing out of the bracket.
4. Lift the idler end of the roller shade assembly and remove the idler
pin from the keyhole in the idler bracket. Place the roller shade
assembly on a clean and soft surface.
Quick Start
1
Advertisement
Table of Contents
Related Manuals for Crestron CSM-QMTDC-163-1-SG-RPR
Summary of Contents for Crestron CSM-QMTDC-163-1-SG-RPR
- Page 1 Quick Start CSM(I)QMTDC-163-1-SG-RPR/RPL QMT® Shade Motor Replacement, Battery Operated Remove the Roller Shade Assembly from the Use the Crestron® CSM(I)-QMTDC-163-SG-RPR/RPL QMT® shade motor Mounting Brackets to replace an existing motor. CAUTION: Roll up the shade fabric to prevent damage during this procedure.
-
Page 2: Replace The Motor
Quick Start CSM(I)QMTDC-163-1-SG-RPR/RPL QMT® Shade Motor Replacement, Battery Operated Replace the Motor Reinstall the Roller Shade Assembly To remove the old motor and then install a new motor: After the motor has been fully installed, roll the fabric back onto the tube (if applicable), and then install the shade assembly. -
Page 3: Motor Wiring
Controls and Indicators Ensure that the cables and connectors do not make contact with the shade fabric. The Crestron CSM(I)-QMTDC shade motors have UP, SET, and DN (down) push buttons that are used to program the shade. The shade Making the Connections... - Page 4 Quick Start CSM(I)QMTDC-163-1-SG-RPR/RPL QMT® Shade Motor Replacement, Battery Operated Test the Shade Travel Adjust the Shade Limits Test the travel of the shade fabric to ensure that it does not come in Shades are shipped from the factory with upper and lower limits set. If contact with building materials and that the upper and lower shade the shade limits are not set, the LED flashes red three times, pauses for limits are properly set.
-
Page 5: Wireless Communications
1. Put the gateway into Acquire mode from the unit itself, the Web UI, Crestron Home™ Setup app, or from Crestron Toolbox. NOTES: If the gateway is part of a Crestron Home™ OS system, the Crestron Home Setup app must be used to enter and exit Acquire mode. For details, refer to... - Page 6 Quick Start CSM(I)QMTDC-163-1-SG-RPR/RPL QMT® Shade Motor Replacement, Battery Operated Leave a Wireless Network If the device did not enter Acquire mode automatically, use the SET button or a power-cycle sequence to enter Acquire mode. Use To leave a wireless network: the power-cycle sequence if the buttons are inaccessible. 1.
-
Page 7: Troubleshooting
If further assistance is required, please contact Crestron Fast flash (1/4-second White The motor is in Identify mode. Support. on, 1/4-second off) Crestron CSM(I)-QMTDC Motor Troubleshooting Slow flash (1/2-second Green The motor is moving from a local on, 1/2-second off) button press. Trouble... -
Page 8: Error State
Possible Cause(s) Action The motor The motor is Reduce the duty cycle of the Crestron CSM(I)-QMTDC motors display error codes using the red LED intermittently exceeding its motor operation. on the interface. The LED flashes a pattern to indicate the error. - Page 9 Crestron disclaims any proprietary interest in the marks and names of others. Crestron is not responsible for errors in typography or photography.
Need help?
Do you have a question about the CSM-QMTDC-163-1-SG-RPR and is the answer not in the manual?
Questions and answers