Crestron QMT 5 Series Installation Manual
Crestron QMT 5 Series Installation Manual

Crestron QMT 5 Series Installation Manual

Shade motor accessories, accessories for shade motor hardware

Advertisement

Quick Links

QMT
5 Series Shade Motor Accessories
®
Accessories for Shade Motor Hardware
Installation Guide

Description

A variety of accessories are available with Crestron
shades. These accessories may be
®
used in circumstances where concealing the shade is desirable or where blackout
conditions are required (e.g., in a movie room).
Additional Resources
Visit the product page on the Crestron website (www.crestron.com)
for additional information and the latest rmware updates. Use a QR
reader application on your mobile device to scan the QR image.

Pockets

A single pocket and a dual pocket are available. Prefabricated pockets reduce the need
for custom framing for the shade and allow an easy installation. A single pocket and a dual
pocket are available for installations where the pocket cannot be built into the window
frame (retro t applications). The inside of the pocket contains grooved lines for easy
drilling and for reducing the need for a center punch. Both pockets are available with a tile
lip that supports the edge of a ceiling tile.
Single Pocket
5-3/16 in
(132 mm)
Grooves for drilling
5-3/8 in
(137 mm)
Single Pocket with Tile Lip
5-3/16 in
(132 mm)
4-3/8 in
(112 mm)
5-1/4 in
(134 mm)
11/16 in
5 in
(18 mm)
(127 mm)

Top and Back Covers

The top and back covers allow the shade hardware to be concealed when the shade is
viewed from above and when the shade is viewed from outside the window. Top and back
covers are available for single brackets (CSA-ARCH5-BRKT and CSA-ARCH5-BRKT-MAN)
and dual brackets (CSA-ARCH5-BRKT-DUAL).

Single Top and Back Cover

4-1/2 in
(115 mm)
4-9/16 in
(117 mm)

Dual Top and Back Cover

6-1/16 in
(154 mm)
9-1/8 in
(232 mm)

Flap

The ap is an accessory that attaches to the inside of the pocket from the room or window
side of the pocket. It blocks the opening at the bottom of the pocket so that the shade and
hardware cannot be seen. The ap can also attach to a hanger.
Flap
3-1/4 in
(84 mm)

Flap Mounting to a Pocket

Hanger

Hangers are designed to mount to the edge of a custom fabricated pocket to hold a ap.
The hanger should be mounted inside the pocket. The hanger with a tile lip is used where
there is a drop ceiling. The side of the hanger contains a grooved line for easy drilling and
for reducing the need for a center punch.
Hanger
Mounting
1-3/16 in
surface
(31 mm)
1/4 in
(6 mm)

Hanger with Tile Lip

11/16 in
(18 mm)
Mounting
1-3/16 in
surface
(31 mm)

Flap Attaching to a Hanger

Fascia

The fascia is available square or round and is designed to t single brackets
(CSA-ARCH5-BRKT) and dual brackets (CSA-ARCH5-BRKT-DUAL). A smaller square fascia
is designed to work with manual shades (CSA-ARCH5-BRKT-MAN).The fascia snaps onto
the tabs of the mounting bracket.
Square and Round Fascias: CSA-ARCH5-BRKT
Square and Round Fascias: CSA-ARCH5-BRKT-DUAL
Square Fascia: CSA-ARCH5-BRKT-MAN

End Caps

Bracket end caps are available for use with fascia and the top and back cover. Pocket end
caps are available for use with pockets that are not recess-mounted and will be exposed
to the room.
There are square or round end caps that are sized to t single shade brackets
(CSA-ARCH5-BRKTand CSA-ARCH5-BRKT-MAN) and dual brackets
(CSA-ARCH5-BRKT-DUAL). Round end caps must be used with a round fascia, and
square end caps must be used with a square fascia. The end cap snaps onto the side of
the brackets. Use the printed directions on the end caps to install them in the proper
orientation and on the proper side of the shade.
Square and Round End Caps: CSA-ARCH5-BRKT and CSA-ARCH5-BRKT-MAN
3-3/16 in
3-3/16 in
(117 mm)
(117 mm)
4-9/16 in
(120 mm)
Square and Round End Caps: CSA-ARCH5-BRKT-DUAL
6-3/16 in
(157 mm)
9-3/16 in
(234 mm)
6-3/16 in
(157 mm)
9-3/16 in
(234 mm)
4-9/16 in
(120 mm)

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the QMT 5 Series and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Crestron QMT 5 Series

  • Page 1 (CSA-ARCH5-BRKT-DUAL). Round end caps must be used with a round fascia, and 4-1/2 in Visit the product page on the Crestron website (www.crestron.com) square end caps must be used with a square fascia. The end cap snaps onto the side of...
  • Page 2 Tel: 888.CRESTRON 01.17 the marks and names or their products. Crestron disclaims any proprietary interest in the marks and Fax: 201.767.7576 Speci cations subject to names of others.

Table of Contents