Ec Declaration Of Conformity; Protecting The Environment; Technical Data - Black & Decker BDST182L1 Original Instructions Manual

ENGLISH
Problem
Automatic line feed does not
feed line.
Overfeeding
Line unravels when cap or
spool is removed

Protecting the environment

Z
Separate collection. Products and batteries
marked with this symbol must not be disposed of
with normal household waste.
Products and batteries contain materials that can be
recovered or recycled reducing the demand for raw materials.
Please recycle electrical products and batteries according
to local provisions. Further information is available at
www.2helpU.com

Technical data

Input Voltage
No-Load Speed min
Weight
14
(Original instructions)
Solution
More line is fed when the line shortens
to approximately 76 mm. To determine if
the line is not feeding, let line wear past
this point.
Keep the tabs depressed and remove the
spoolcap with the spool from the spool
housing in the trimmer head.
Ensure that the line is not crisscrossed
on the spool as detailed in (Fig. U). If
it is unwind the cutting line and rewind
it neatly.
Inspect tracks at the bottom of spool for
damage. If damaged, replace spool.
Pull the cutting line until it protrudes
approximately 122 mm from the spool. If
insufficient cutting line is left on the spool,
install a new spool of cutting line.
Align the tabs on the spool cap with the
cut outs in the housing.
Push the spool cap onto the housing until
it snaps securely into place.
If the cutting line protrudes beyond the
trimming blade, cut it off so that it just
reaches the blade. If the automatic line
feed still does not work or the spool is
jammed, try the following suggestions:
Carefully clean the spool and housing.
Make sure you are using correct line
size and diameter (2.00 mm) - smaller
and larger line sizes will affect the
functionality of the auto feed system.
Remove the spool and check if the lever
in the spool housing can move freely.
Remove the spool and unwind the cutting
line, then wind it on neatly again. Replace
the spool into the housing.
Ensure you are cutting with the tip of
the line 177 mm from the spool. Use the
edge guide if needed to ensure proper
space is maintained.
Ensure you are not exceeding a 10º
angle as shown in (Fig. J1). Avoid contact
of the line with hard surfaces such as
brick, concrete, wood etc. This will
prevent excessive wear and/or overfeed
of line. Cut with the tip of the line
Make sure to park the lines in holding
slots (Figure P) before removing.
BDST182ST1, BDST182L1 (H2)
V
DC
5500 - 7400
-1
kg
Battery
Voltage
Capacity
Type
Charger
Input Voltage
Output Voltage
Current
Hand/arm weighted vibration value according to
= < 2,5 m/s
L (sound pressure) 78.5 dB(A)
PA
uncertainty (K) = 3 dB(A)

EC declaration of conformity

MACHINERY DIRECTIVE
OUTDOOR NOISE DIRECTIVE
BDST182ST1, BDST182L1
Cordless String Trimmer
Black & Decker declares that these products described under
"technical data" are in compliance with:
EN60335-1:2012 + A11:2014, EN50636-2-91:2014
2000/14/EC, Lawn Trimmer, L ≤ 50 cm, Annex VI
DEKRA Certification B.V. Meander 1051 / P.O. Box 5185
6825 MJ ARNHEM / 6802 ED ARNHEM, Netherlands
Notified Body ID No.: 0344
Level of sound power according to 2000/14/EC
(Article 12, Annex III, L ≤ 50 cm):
L (measured sound power) 92.5 dB(A)
WA
uncertainty (K) = 3.33 dB(A)
L (guaranteed sound power) 96 dB(A)
WA
These products also comply with Directive
2006/42/EC, 2014/30/EU and 2011/65/EU.
For more information, please contact Black & Decker at the
following address or refer to the back of the manual.
18
2.1
V
DC
Ah
V
AC
V
DC
mA
EN50636-2-91:
, uncertainty (K) = 1,5 m/s
2 2
BL2518
18
2.5
Li-Ion
906068**
230
18
2000
.