Related Manuals for ADTRAN FXS+ Quad
Summary of Contents for ADTRAN FXS+ Quad
- Page 1 FXS+ Quad Voice Option Module Part Number 1200300L1 & FXS+ Dual Option Voice Modules Plug-in Part Number 1200302L1 Plug-on Part Number 1200304L1 User Manual 61200300L1-1C May 1999...
- Page 2 Trademarks: MEGACOM is a registered trademark of AT&T SLC96 is a registered trademark of AT&T 901 Explorer Boulevard P.O. Box 140000 Huntsville, AL 35814-4000 (256) 963-8000 © 1999 ADTRAN, Inc. All Rights Reserved. Printed in U.S.A.
- Page 3 ADTRAN Year 2000 (Y2K) Readiness Disclosure ADTRAN has established a Year 2000 program to ensure that our products will correctly function in the new millennium. ADTRAN warrants that all products meet Y2K specifications regardless of model or revision. Information about ADTRAN’s Y2K compliance program is available at the fol-...
- Page 4 Notes provide additional useful information. Cautions signify information that could prevent service interrup- tion. Warnings provide information that could prevent damage to the equipment or endangerment to human life.
- Page 5 Federal Communications Commission Radio Frequency Interference Statement This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equip- ment is operated in a commercial environment.
- Page 6 Important Safety Instructions When using your telephone equipment, please follow these basic safety precau- tions to reduce the risk of fire, electrical shock, or personal injury: Do not use this product near water, such as near a bath tub, wash bowl, kitchen sink, laundry tub, in a wet basement, or near a swimming pool.
- Page 7 WARRANTY AND CUSTOMER SERVICE ADTRAN will replace or repair this product within five years from the date of shipment if the product does not meet its published specifications or if it fails while in service. For detailed warranty, repair, and return information see the ADTRAN Equipment Warranty and Repair and Return Policy Procedure on the inside back page of this manual.
- Page 8 viii...
-
Page 9: Table Of Contents
Table of Contents Chapter 1. Introduction ..................1-1 FXS+ Quad and Dual Voice Overview ..............1-1 FXS+ Uses ......................1-1 Functional Description ..................1-2 Features........................ 1-2 FXS+ Option Module Specifications..............1-3 Physical Description ....................1-4 Chapter 2. Installation .................... 2-1 Unpack and inspect .................... - Page 10 SET 2W OUTPUT (Set 2-Wire Output) ..........3-16 TSU Features Used With FXS+ Options............3-17 FACTORY RESTORE ................3-17 RUN SELF-TEST ..................3-17 Appendix A. FXS+ Failure Messages..............A-1 Appendix B. Signalling States ................B-1 Index ........................Index-1 FXS+ Quad and Dual Voice User Manual 61200300L1-1A...
- Page 11 List of Figures Figure 1-1. FXS+ Quad & Dual Voice Option Modules ........1-4 Figure 2-1. Installing Option Module ..............2-3 Figure 3-1. TSU Main Menu ..................3-2 Figure 3-2. Port Status Submenus ................3-4 Figure 3-3. 2-Wire Status Display .................3-4 Figure 3-4. View Signalling Bits Display .............3-5 Figure 3-5.
- Page 12 List of Figures FXS+ Quad & Dual Voice Option Module User Manual 61200300L1-1...
- Page 13 Table B-4. FXS+ Mode (Ground Start) .............. B-4 Table B-5. Single Mode ..................B-5 Table B-6. UVG Mode: Loop Start Provisioning on T-Span ......B-6 Table B-7. UVG Mode: Ground Start Provisioning on T-Span ...... B-7 61200300L1-1 FXS+ Quad and Dual Voice Option Module xiii...
- Page 14 List of Tables FXS+ Quad and Dual Voice Option Module User Manual 61200300L1-1...
-
Page 15: Chapter 1. Introduction
The FXS+ Dual plug-in option module also accepts the TSU 100/120/600 plug-on boards to provide up to four functional ports per option slot used. Signalling and interfaces comply 61200300L1-1 FXS+ Quad & Dual Voice Option Module User Manual... -
Page 16: Functional Description
Integral 1 kHz tone generation sends test tone toward near or far end • Manual control of Tx A and Tx B signal bits • Manual control of 2-wire interface supervision output FXS+ Quad & Dual Voice Option Module User Manual 61200300L1-1... -
Page 17: Fxs+ Option Module Specifications
RJ-45 Ring Generator 20 Hz 40 Vrms 2.0 REN, per port Tests Power-on circuit test Signal bits monitoring and setting 1 kHz test tone generation Force 2-wire port output state 61200300L1-1 FXS+ Quad & Dual Voice Option Module User Manual... -
Page 18: Physical Description
PO RT X. 4 HO T RE PLA CE ABL E Figure 1-1. FXS+ Quad & Dual Voice Option Modules The rear panel of the dual plug-in module includes a plastic plug over a cutout for additional connectors. This allows a plug-on board to be added to the FXS+ dual plug-in module. -
Page 19: Chapter 2. Installation
FXS+ Quad/Dual Voice option module • FXS+ Quad/Dual Voice Option Module User Manual (to be inserted into main TSU 100/120/600 manual) Items Provided by Customer • Cable to connect the unit to the station. 61200300L1-1 FXS+ Quad & Dual Voice Option Module User Manual... -
Page 20: Installing The Fxs+ Voice Option Module
For assistance with software revision upgrades, please contact ADTRAN Technical Support at 1-888-4ADTRAN. For ease of replacement, power to the TSU 100/120/600 may be On when installing or removing the FXS+ Quad and Dual Voice option modules. FXS+ Quad & Dual Voice Option Module User Manual... -
Page 21: Placement Of The Option Module
Figure 2-1. Installing Option Module Power Connection Each FXS+ module derives power from the base TSU 100/ 120/600 unit. Power to the TSU 100/120/600 is supplied by a captive eight-foot power cord. 61200300L1-1 FXS+ Quad & Dual Voice Option Module User Manual... -
Page 22: Wiring
Chapter 2. Installation Wiring The FXS+ Quad and Dual Voice option module analog voice interface connectors are universal and accept either an RJ-45 (8-pin modular plug) or an RJ-11 (6-pin modular plug). The pinout is shown in Table 2-1. The required wiring connection is:... -
Page 23: Power Up Testing And Initialization
FXS+ module are identified in Appendix A, FXS+ Failure Messages. Operation Alarms The red ALARM LED with the module LEDs on the front panel illuminates when an alarm condition is detected. 61200300L1-1 FXS+ Quad & Dual Voice Option Module User Manual... -
Page 24: Configuration Of Tx Level (Tlp)
TX LVL should be set to +3 dB . For point-to-point applications where the channel terminates in other customer equipment, any TX LVL may be used. A+3 dB TLP setting attenuates the analog signal by 3 dB. FXS+ Quad & Dual Voice Option Module User Manual 61200300L1-1... -
Page 25: Chapter 3. Operation
With the cursor on one of the Port menu items, press Enter display a list of the currently installed option modules. To activate menus for the FXS+ option module, scroll through the list to display X.1 FXS+ and press Enter 61200300L1-1 FXS+ Quad & Dual Voice Option Module User Manual... -
Page 26: Figure 3-1. Tsu Main Menu
6) PORT UTILITY 4) TEST 2) RUN SELF-TEST 3) PORT TEST 4) CANCEL TEST Figure 3-1. TSU Main Menu Additional item menus may be displayed on the TSU 600/600e products FXS+ Quad & Dual Voice Option Module User Manual 61200300L1-1... -
Page 27: Fxs+ Menu Items
Enter following submenus. • 2W STATUS (2-wire status) • VIEW SIG BITS (View Signalling Bits) • SLC96 STATUS (2-wire status when SINGLE or UVG modes) 61200300L1-1 FXS+ Quad & Dual Voice Option Module User Manual... -
Page 28: Figure 3-2. Port Status Submenus
An asterisk is present if loop current is flowing through the 2-wire circuit. An asterisk is present if ringing voltage is being ap- Ringing plied to the 2-wire circuit from the ring-generator on the FXS+ option module FXS+ Quad & Dual Voice Option Module User Manual 61200300L1-1... -
Page 29: Figure 3-4. View Signalling Bits Display
( VIEW SIG BITS ). SLC96 STATUS is only available when SINGLE or UVG modes of operation are selected. See Figure 3-5. Figure 3-5. SLC96 Status Display 61200300L1-1 FXS+ Quad & Dual Voice Option Module User Manual... -
Page 30: Port Config (Port Configuration)
1) MODE 2) CONFIG 7) PORT CONFIG 2) RX LVL (TLP) 1.2 FXS+ 3) TX LVL (TLP) 4) FAULT RESP 5) ANSWER S’VSN 6) TANDM OPTIONS Figure 3-6. Port Configuration Submenus FXS+ Quad & Dual Voice Option Module User Manual 61200300L1-1... -
Page 31: Mode
When using this mode, line-current dropout for 500 ms is provided when a call terminates and the far-end hangs up. This may be useful for voice-mail or modem systems that need far-end disconnect supervision. This mode also requires 61200300L1-1 FXS+ Quad & Dual Voice Option Module User Manual... - Page 32 When both ends are off-hook, a direct point-to-point connection is established. Ringing cadence is two seconds on, four seconds off. FXS+ Quad & Dual Voice Option Module User Manual 61200300L1-1...
- Page 33 UVG (Ground Start) supervision on the 2-wire inter- at the Digital Switch... face. No other settings are necessary to configure the supervision, as the far-end determines it. Channel Test signalling is ignored. 61200300L1-1 FXS+ Quad & Dual Voice Option Module User Manual...
-
Page 34: Rx Lvl (Tlp) (Receive Level/Transmit Level Point)
Enabling ANSWER S’VSN will not cause polarity reversal on the 2W when receiving a wink in TANDEM modes. Use the setting to respond to a wink. LOOP REV BAT Choices: Enable, Disabled 3-10 FXS+ Quad & Dual Voice Option Module User Manual 61200300L1-1... -
Page 35: Tandm Options (Tandem Options)
FXS+ card is in one of the tandem modes. This may be needed in cases where the network does not provide ringback tone. Choices: Enabled, Disabled 61200300L1-1 FXS+ Quad & Dual Voice Option Module User Manual 3-11... - Page 36 CPE, even if there is no answer. If this option is left disabled, the FXS+ option module will not wink until the incoming call is answered. Choices: Enabled, Disabled 3-12 FXS+ Quad & Dual Voice Option Module User Manual 61200300L1-1...
-
Page 37: Port Configuration Menu Items/Parameters Summary
SUPERVISION *Immediate, Wink DIAL TONE *Disabled, Enabled LOOP REV BAT *Disabled, Enabled RINGBACK *Disabled, Enabled DNIS DELAY *Disabled, 0.5 to 5 seconds DNIS WINK T/O *Disabled, Enabled *Factory Default 61200300L1-1 FXS+ Quad & Dual Voice Option Module User Manual 3-13... -
Page 38: Port Util (Port Utility)
The Port Utility submenu contains a second option, Command Mode , for the FXS+ module. This option is reserved for factory use only. Press Cancel to exit or to select another port. 3-14 FXS+ Quad & Dual Voice Option Module User Manual 61200300L1-1... -
Page 39: Port Test
(the 2-wire interface on the option module). This tone may be used for testing or relative level measurements. When 1 is enabled, ringing and dial-tone for other channels on TONE the slot are suspended. Choices: Off, Near, Far 61200300L1-1 FXS+ Quad & Dual Voice Option Module User Manual 3-15... -
Page 40: View Sig Bits (View Signalling Bits)
VIEW SIG BITS Display only SET TX SIGNAL Off, (A=0, B=0), (A=0, B=1), (A=1, B=0), (A=1, B=1) SET 2W OUTPUT Off, Disabled, Tip Open, Active, Re- verse Battery, Ringing 3-16 FXS+ Quad & Dual Voice Option Module User Manual 61200300L1-1... -
Page 41: Tsu Features Used With Fxs+ Options
When RUN SELF-TEST displays, place the cursor on it and press to execute the test. The unit continuously changes Enter the display in the LCD window until all test results are shown. 61200300L1-1 FXS+ Quad & Dual Voice Option Module User Manual 3-17... - Page 42 Chapter 3. Operation 3-18 FXS+ Quad & Dual Voice Option Module User Manual 61200300L1-1...
-
Page 43: Appendix A. Fxs+ Failure Messages
Could not detect ring ground E05 - RINGING Could not detect ring trip E10 - SIGNALING Failure of signal bit transmission FXS+ Alarm Messages No alarms are specified for the FXS+ Voice option module. 61200300L1-1 FXS+ Quad and Dual Voice Option Module User Manual... - Page 44 Appendix A. FXS+ Failure Messages FXS+ Quad and Dual Voice Option Module User Manual 61200300L1-1...
-
Page 45: Appendix B. Signalling States
The A and B signal bit states on the DS-1 signal are as follows: Signal Means logic 0 is the DS-1 stream logic 1 is the DS-1 stream value is not significant Loop Open phone on-hook Loop Closed phone off-hook 61200300L1-1 FXS+ Quad and Dual Voice Option Module User Manual... -
Page 46: Table B-2. Tandem Modes
The A and B signal bit states on the DS-1 signal are as follows: Signal Means logic 0 is the DS-1 stream logic 1 is the DS-1 stream value is not significant Loop Open phone on-hook Loop Closed phone off-hook FXS+ Quad and Dual Voice Option Module User Manual 61200300L1-1... -
Page 47: Table B-3. Fxs+ Mode (Loop-Start
1 is the DS-1 stream logic 1 followed by a logic 0 in each successive signalling frame. value is not significant Loop Open phone on-hook Loop Closed phone off-hook 61200300L1-1 FXS+ Quad and Dual Voice Option Module User Manual... -
Page 48: Table B-4. Fxs+ Mode (Ground Start
0 is the DS-1 stream logic 1 is the DS-1 stream logic 1 followed by logic 0 in each successive signalling frame value is not significant Loop Open phone on-hook Loop Closed phone off-hook FXS+ Quad and Dual Voice Option Module User Manual 61200300L1-1... -
Page 49: Table B-5. Single Mode
0 is the DS-1 stream logic 1 is the DS-1 stream logic 1 followed by logic 0 in each successive signalling frame value is not significant Loop Open phone on-hook Loop Closed phone off-hook 61200300L1-1 FXS+ Quad and Dual Voice Option Module User Manual... -
Page 50: Table B-6. Uvg Mode: Loop Start Provisioning On T-Span
1 is the DS-1 stream logic 1 followed by logic 0 in each succes- sive signalling frame value is not significant Loop Open phone on-hook Loop Closed phone off-hook FXS+ Quad and Dual Voice Option Module User Manual 61200300L1-1... -
Page 51: Table B-7. Uvg Mode: Ground Start Provisioning On T-Span
1 is the DS-1 stream logic 1 followed by logic 0 in each succes- sive signalling frame value is not significant Loop Open phone on-hook Loop Closed phone off-hook 61200300L1-1 FXS+ Quad and Dual Voice Option Module User Manual... - Page 52 Appendix B. Signalling States FXS+ Quad and Dual Voice Option Module User Manual 61200300L1-1...
- Page 53 DNIS WINK T/O 3-12 FXS+ Quad and Dual Voice, overview DNIS Wink T/O, port config menu item 3-13 FXS+, description 1-2 DNIS Wink Timeout 3-12 FXS+, physical description 1-4 61200300L1-1 FXS+ Quad and Dual Voice Option Module User Manual Index-1...
- Page 54 Self-test, failed 2-5 Physical Description, of FXS+ modules Self-Test, successful 2-5 SET 2-W OUTPUT (Set 2-Wire Output) PLAR 3-8 3-16 PORT CONFIG (Port Configuration) 3- Set TX SIGNAL (Set Transmit Signal) Index-2 FXS+ Quad and Dual Voice Option Module User Manual 61200300L1-1...
- Page 55 THL SRL, specification 1-3 Tip and Ring polarity, FXS_LS 3-7 Transmission Levels, specification 1- Y2K Project Line iii Y2K Readiness Disclosure iii TSU Main Menu 3-2 Y2K, Faxback Document Line iii 61200300L1-1 FXS+ Quad and Dual Voice Option Module User Manual Index-3...
-
Page 56: Index
Index Index-4 FXS+ Quad and Dual Voice Option Module User Manual 61200300L1-1... - Page 57 (800) 615-1176 Sales (800) 827-0807 Post-Sale Support Please contact your local distributor first. If your local distributor can- not help, please contact ADTRAN Technical Support and have the unit serial number available. Technical Support (888) 4ADTRAN Repair and Return If ADTRAN Technical Support determines that a repair is needed, Tech- nical Support will coordinate with the Customer and Product Service (CAPS) department to issue an RMA number.