Important Safety Instructions; Mounting Instructions - ecolight UC1034-BR2-12LF0-E Instruction Manual

Important Safety Instructions

This unit has a polarized plug (one blade is wider than the other) as a safety
feature. This plug will only fit in a polarized outlet one way. If the plug does
not fit completely into the outlet, reverse the plug. If it still does not fit,
contact a qualified electrician. Never use with a power strip unless the plug
can be completely inserted. Do NOT attempt to defeat this feature.
WARNING: To reduce the risk of FIRE, ELECTRIC SHOCK, OR INJURY TO
PERSONS:
1. For INDOOR USE ONLY.
2. Do NOT touch LEDs.
3. Do NOT remove the protective clear LED lens.
4. Do NOT look directly at lighted LEDs for any length of time.
5. Do NOT touch, operate, or install fixture while in contact with water.
6. Not intended for illumination of aquariums.
7. Not intended for recessed installation in ceilings or soffits.
8. Do NOT mount over sinks or stoves.
9. Do NOT mount the light to cabinets having a material thickness less
than 1/4 in.
10. Do NOT install the fixture inside of enclosed cabinets.
11. Electrical requirements:120 V AC, 60 Hz, 0.16 A MAX.
12. Do NOT attempt to install while plugged in.
13. Do not use an extension cord. Use a power strip with integral
overcurrent protection to supply power to the fixture.
14. Use only insulated staples or plastic ties (not included) to secure the cords.
15. Do not run ANY cords behind walls, ceilings, soffits, cabinets or a similar
permanent structure where it may be inaccessible for examination.
16. The total wattage of ALL the fixtures linked together in one chain should
NOT exceed 360 watts. Exceeding the total wattage will result in a
hazardous situation.
SAVE THESE INSTRUCTIONS IN A LOCATION CLOSE TO THE FIXTURE TO
REFER TO THEM AT A LATER TIME.

Mounting Instructions

Find a suitable location to mount the fixture that will reach the power supply. The fixture
can be installed in two ways. Keyhole installation would be installed using the provided
hardware kit. Easy installation would be installed using the captive mounting screws
which are preinstalled on the front side of the end caps.
1
KEYHOLE INSTALLATION: Locate the mounting keyhole slots on the back of the fixture.
Measure the center-to-center distance to determine the distance the wood screws
need to be installed. Measure and mark the corresponding placement on the mounting
surface. NOTE: Make sure the mounting location is within 5 ft. of an electrical outlet.
2
Fig. 1
3
Fig. 2
4
Fig. 3
Place a grommet over each wood screw. Drive in the
two wood screws until the grommets contact the
bottom of the mounting surface. Then turn the screws
another 1/4 turn (Fig. 1). The screws must be driven in
straight for the fixture to mount properly.
EASY INSTALLATION:
For installation using pilot holes for the screws, place
the fixture firmly against the mounting surface. While
holding in position, mark the surface for the pilot hole
locations by turning both screws with a Phillips
screwdriver until they dimple the surface. Using a 1/16
in. drill bit, drill the pilot holes for the screws. Secure
the fixture to the cabinet by tightening the mounting
screws into the drilled pilot holes (Fig. 2). The fixture
can also be mounted without the use of pilot holes by
firmly holding the fixture against the mounting surface
and turning the mounting screws until the fixture is
snug against the surface.
To install additional lights, unplug the first fixture that
the additional fixtures will be connected to. Repeat
Steps 1-2 or 3 for the additional fixtures. NOTE: Make
sure the lights are close enough that the linking cord
will plug in securely (18" MAX.). The linking cord has
two different ends: one input and one output. They are
designed to plug-in one way only (Fig. 3). Overriding
this feature could result in a dangerous situation. Leave
the plug cover on the last fixture, since it will not be
hooked up to another fixture.
- 2 -