Advertisement
Important Safety Instructions
This unit has a grounded plug as a safety feature. This plug will only fit in an
outlet one way. If it does not fit, do not use the outlet or contact a qualified
electrician. Never use with a power strip unless the plug can be completely
inserted. Do NOT attempt to defeat this feature.
WARNING: To reduce the risk of FIRE, ELECTRIC SHOCK, OR INJURY TO
PERSONS:
1. For INDOOR USE ONLY.
2. Not intended for installation in plastic cabinets.
3. The mounting surface should be flat and sturdy enough to support the
fixture.
4. Do NOT mount the fixture to cabinets having a material thickness less
than 1/4 in.
5. Not intended for recessed installation in ceilings or soffits.
6. Do NOT use in wet locations.
7. Do NOT use for illumination of aquariums.
8. Do NOT mount over sinks or stoves.
9. Do NOT touch, operate, or install fixture while in contact with water.
10. Do not remove the protective LED lens or touch the LEDs at any time.
11. Use a soft cloth to clean the diffuser and/or fixture.
PLUG-IN/LINKING SAFETY INFORMATION:
12. Do NOT attempt to install while plugged in.
13. Use only insulated staples or plastic ties to secure the power or linking
cords.
14. The National Electrical Code (NEC) does not permit cords to be
concealed where damage to insulation may go unnoticed. To prevent
fire danger, do not run cord behind walls, ceilings, soffits, cabinets, or
similar permanent structures where it may be inaccessible for
examination. Cords should be visually examined periodically and
immediately replaced when any damage is noted.
15. Do not use an extension cord. Use power strip with integral overcur-
rent protection to supply power to the fixture.
16. The total wattage of ALL the fixtures linked together in one chain
should NOT exceed 360 watts. Exceeding the total wattage will result in
a hazardous situation. Fixture wattage can be found on back of fixture.
IMPORTANT: These LED light heads use light emitting diodes to provide
light. LEDs are electronic semiconductors and do not have a filament that
can burn out like an ordinary light bulb. As such, the LED light heads can
last up to 50,000 hours when used intermittently, and therefore, never need
replacing.
SAVE THESE INSTRUCTIONS IN A LOCATION CLOSE TO THE LIGHT
FIXTURE TO REFER TO THEM AT A LATER TIME. Before installation, plug in
fixture to a 120 V, 60 Hz electrical outlet to check for proper operation. Then,
unplug and begin the installation.
Dimmer Instructions
THIS FIXTURE IS DIMMABLE BY SPECIFIC FORWARD PHASE ELECTRONIC (TRAIC)
DIMMERS. Dimmers tested to be compatible with this fixture are the Lutron: Diva®
C*L™: DVWCL-153P* or DVCL-153P*, Lumea® C*L™: LGCL-153P*, and Toggler® C*L
™: TGCL-153P*. Not recommended for use with motion or light sensors, timers, or
any other external controls.
Mounting Instructions
There are two methods to mount the fixture to a cabinet. The first is the EASY
MOUNTING INSTALLATION method that uses the pre-installed screws located at
both ends of the fixture. The other is the TRADITIONAL MOUNTING INSTALLATION
method, which utilizes the keyhole slots located on the backside of the fixture.
Power-In
Port
to a power supply. The "Power-Out" port is located at the opposite end and is used to
link power to additional fixtures connected together.
EASY MOUNTING INSTALLATION
1
Before mounting, find a suitable location to mount the
fixture that will reach the power supply (within 5 feet)
or to reach adjoining fixture (within 18 inches). The
fixture has two power ports located at each end of the
Power-Out
fixture. The "Power-In" port is located on the end next
Port
to the on/off switch and is used to connect the fixture
The fixture can be mounted without utilizing pilot holes.
Firmly hold the fixture against the mounting surface and
begin turning the mounting screws until they are fully
driven in and the fixture is firmly attached to the
mounting surface (Fig. 1). NOTE: DO NOT overtighten
the screws, as it may result in damage to the fixture or
the mounting surface. Direct Wire Installation Only:
Determine the fixture location, but do not mount until the
Fig. 1
wiring steps are completed.
- 2 -
Advertisement
