IP Varifocal Camera
Quick Star t Guide
■ Please read this instruction carefully before using the product and keep
it for further reference.
■ All the examples and pictures used here are for reference only.
■ The contents of this manual are subject to change without notice.
Precautions
1
■ If the product does not work properly, please contact your dealer or the
nearest service center. Never attempt to disassemble the camera yourself. (We
shall not be responsible for any problems caused by unauthorized repair or
maintenance.)
■ Do not allow water or liquid intrusion into the camera.
■ In the use of the product, you must be strict compliance with the electrical
safety regulations of the nation and region. When the product is mounted on wall
or ceiling, the device shall be firmly fixed.
■ Do not use camera beyond specified voltage range.
■ Do not drop the camera or subject it to physical shock.
■ Avoid touching the camera lens.
■ If cleaning is necessary, please use clean cloth to wipe it gently.
■ Do not aim the camera at the sun or extra bright place.
■ Do not place the camera in extremely hot, cold (the operating temperature
shall be -30˚C~60˚C), dusty or damp locations, and do not expose it to high
electromagnetic radiation.
Contents
2
Camera
Quick start guide
4 tapping screws PA 4×25
CD
Drill template
Rubber plug
Screwdriver
3
Overview
Type A: Motorized zoom camera
Type B: Manual zoom camera
Lens cover
7B
* If the PoE switch is used to power the camera, DC12V power supply is not
required.
* It is recommended to install the security cap for outdoor installation.
Connecting Network Cable
Plastic plug
×4
CVBS&DC
1
IN cables
1
2
3
1
Ethernet Connector
4
2
Audio Input (MIC)
5
3
Audio Output (HP)
6
4
CVBS Video Output
5
Alarm Input/Output
6
DC12V Power Connector
7A Zoom- (only available for type A)
8A Zoom+ (only available for type A)
7B Focus
11
10
8B Zoom
7A
9
Micro SD Card Slot
8A
9
10
Reset
11
DC IN & CVBS Interface
IR light hood
8B
1--ALM-COM
2--ALM-OPEN
3--ALM-INA
4--ALM-GND
DC12V
2
① Loosen the nut from the main element (security cap).
② Run the network cable (without RJ 45 connector) through the both
elements. Then crimp the cable with RJ 45 connector.
③ Connect the cable to the hermetic connector. Then tighten the nut and
the main cover.
4
Installation
* Please make sure that the wall or ceiling is strong enough to withstand 3
times the weight of the camera.
* Please install the camera in the dry environment. You'd better install back the
lower dome less than 4 hours after removing it.
*
Do not remove the protection film until finishing the installation.
①
Rotate the trim ring anticlockwise to remove it from the camera.
② Attach the drill template to the place where you want to fix the camera
and then drill 4 screw holes and 1 cable hole (if you want to route the cables
through the ceiling) according to the drill template.
Trim Ring
Figure 1
③ Loosen the screws to open the lower dome.
④ Route and connect these cables. Then secure the camera to the
ceiling or wall with the screws provided.
Figure 3
⑤
Three-axis adjustment. Before adjustment, preview the image of the
camera on a monitor (See Figure 5) and then adjust the camera according to
the figure below to get an optimum angle.
Figure 4
Tilt 0°~77°
Hold it and rotate
3
Rotation 0°~345°
90.2mm
∅4 . 6
90.2mm
Figure 2
Rubber plug
* Install it when routing the cables
through the ceiling.
Lower dome
Pan 0°~345°