LG 55EW960H Commercial Mode Setup Manual page 38

Installer Menu (Cont.)
092 - HDMI3 ENABLE
Set to 1 to enable HDMI 3 input in DTV Mode. Set to 2 to enable
HDMI 3 input in PC Mode. Set to 0 to disable display panel HDMI
3 input.
093 - RJP AVAILABLE (Remote Jack Pack Available)
•
0 = Remote jack pack is not available or disabled.
•
1 = Legacy Model RJPs: HDMI Mode
Enables RJP feature for use with full cable bundle models. In
this mode, when an HDMI source is connected to the RJP, both
digital video and audio are expected via the HDMI cable. If no
digital audio is present, no audio will be heard.
•
2 = Legacy Model RJPs: DVI Mode
Enables RJP feature for use with full cable bundle models. In
this mode, when an HDMI/DVI source is connected to the RJP,
only digital video is expected via the HDMI cable. Analog audio
is provided via a separate cable, from the source, connected to
an RJP AUDIO IN. If no analog audio cable is connected, tuner
audio will be heard.
•
5 = Scaler Model RJPs: HDMI Mode
Enables RJP feature for use with reduced cable bundle models.
In this mode, when an HDMI source is connected to the RJP,
both digital video and audio are expected via the HDMI cable. If
no digital audio is present, no audio will be heard.
•
6 = Scaler Model RJPs: DVI Mode
Enables RJP feature for use with reduced cable bundle models.
In this mode, when an HDMI/DVI source is connected to the
RJP, only digital video is expected via the HDMI cable. Analog
audio is provided via separate cable, from the source, connected
to an RJP AUDIO IN. If no analog audio cable is connected,
tuner audio will be heard.
Note: See also Reference section, "RJP Model List & Input Auto-
sensing Hierarchy." Settings 1, 2, 5, and 6 allow the lodge staff to
customize each TV's RJP setup based on customer requirements.
Note: When this item is enabled in the Installer Menu, item 042
AUTO INPUTS is automatically set to 0.
094 - SAP MENU EN (2nd Audio Program)
Set to 1 to enable the SAP feature in the Function Menu, when
the Function Menu is available (i.e., TV is not in Pass-through
Mode). Set to 0 to disable the SAP feature in the Function Menu,
when the Function Menu is available.
096 - DEF. ASP. RATIO (Default Aspect Ratio)
Selects default aspect ratio at power up:
0 = Set By Program
2 = 16:9 (default)
4 = Zoom
Note: This item is not available in the Installer Menu unless item
106 ASP RATIO LOCK is set to 0.
38
1 = 4:3
3 = Just Scan
097 - AUDIO OUTPUT
Determines availability and signal type/level (fixed speaker,
variable speaker, or fixed line level [amplifier]) of the audio output to
be used by external audio equipment connected to the SPEAKER
OUT / LINE OUT jack on the TV. Set to 0 to disable audio output.
Otherwise, see the table below and set as required in accordance
with audio equipment. See also Reference section, "External
Stereo Speaker Specifications."
Value
Speaker Output 1
2
3
4
5
6
7
8
Line Output 9
098 - PRO:CENTRIC
Selects the Pro:Centric Application Mode. Set to 0 (default) to
disable the Pro:Centric application. Set to 1 for Flash Mode. Set
to 2 for GEM (Java Application) Mode. Set to 3 for HTML Mode.
In order to retrieve the Pro:Centric application, when enabled (for
Flash, GEM, or HTML Mode), the TV must be turned OFF/ON two
times. Once you exit the Installer Menu, turn OFF the TV for at
least one minute. When you turn the TV back ON, the TV will start
the appropriate library based on the setting of this item. Wait until
TV programming appears on the display, and then turn the TV
back OFF, this time for a few minutes, to initiate the application
download. When you turn the TV back ON, press PORTAL on the
Installer Remote, and verify that the Pro:Centric application
appears on the display.
Note: This item is not available in the Installer Menu when item
119 DATA CHANNEL is set to 0.
Note: The Installer Remote shipped with the EW960H TV models
supports MMR operation. However, if configuring the TV for GEM
(Java Application) Mode, please note that the MMR operation is
incompatible with LG's Java application. Either set Installer Menu
item 101 IR FEEDBACK to 2 in order to disable the TV's MMR
feature, or use a standard IR remote with the TV.
099 - BACK LIGHTING
Sets the TV screen brightness at power up. Default setting is 255.
•
1 (dimmest picture) – 100 (brightest picture) Static Back Lighting
•
101 (dimmest picture) – 2 00 (brightest picture) Dynamic Back
Lighting: The TV automatically controls back lighting depending
upon the picture level of the current program.
Status
Fixed 0.01 Watts
Fixed 0.03 Watts
Fixed 0.05 Watts
Fixed 0.10 Watts
Fixed 0.20 Watts
Fixed 0.50 Watts
Fixed 1.00 Watt (default)
Control with volume
Fixed line level (typically 400 mVrms ±
100 mVrms @10KΩ) output
206-4307