Uplift Desk UDA126 Quick Start Manual

Swing Laptop Sit/Stand Workstation
SKU: UDA126

Package Contents

A (x1) B (x1)
A (x1) B (x1)
Base Arm
A (x1) B (x1)
D (x1)
D (x1)
F (x1)
Upper Clamp Lower Clamp
F (x1) G (x1) H (x1)
F (x1) G (x1) H (x1)
D (x1)
• Maximum weight capacity: 19.8 lb
R (x2) O (x1)
• Recommended laptop size: up to 17" R (x2) O (x1)
• Desktop thickness compatibility: between 0.4"-3.3" thick
There are two ways to attach the Swing Laptop Sit/Stand Workstation to your desktop. If you would like to attach it along
the back edge of your desktop, follow the Clamp Method instructions on this page. If you prefer to attach it through your
F (x1) G (x1) H (x1)
desktop, follow the Bolt-Through Method instructions starting on page 2.
R (x2) O (x1)

Clamp Method

Clamp Method
fig. 1
A (x1)
M6x12
A (x1) B (x1)
M6x12
J (x4)
J (x4)
A (x1) B (x1)
M8
A (x1)
P (x2)
P (x2)
D8
C (x1)
Q (x2)
C (x1)
A (x1) B (x1)
Q (x2)
M6x20
M6x20
K (x2)
D (x1)
A (x1)
K (x2)
D (x1)
T (x1)
T (x1)
D (x1)
Tray Mount
D (x1)
3mm
C (x1)
I (x4)
L (x1)
I (x4)
D (x1) L (x1)
4mm
M (x1)
A (x1)
M (x1)
F (x1) G (x1)
6mm
G (x1) H (x1)
F (x1)
N (x1)
Clamp Plate
E (x1)
N (x1)
F (x1) G (x1) H (x1)
E (x1)
F (x1) G (x1) H (x1)
F (x1) A (x1)
I (x4) D (x1)
R (x2)
S (x2)
R (x2) O (x1)
S (x2)
R (x2) O (x1)
R (x2) O (x1)
D (x1)
R (x2)
F (x1) G (x1)
E (x1)
F (x1) G (x1)
R (x2)
R (x2)
S (x2)
Bolt-Through Method
fig. 2
© UPLIFT Desk • 800-349-3839 • info@upliftdesk.com • upliftdesk.com
B (x1) C (x1)
clamp/bolt-t upper mount to Base
C (x1)
clamp/bolt-t upper mount to Base M6x12
J (x4)
C (x1)
B (x1) C (x1)
bolt-t plate to Base
M8
M8
bolt-t plate to Base
P (x2)
M6x12
clamp/bolt-t upper mount to Base
J (x4)
bolt-t plate to Base
D8
D8
bolt-t plate to Base
C (x1)
Q (x2)
Tray mount to Tray
M8
M6x20
Tray mount to Tray bolt-t plate to Base
I (x4)
B (x1) C (x1)
P (x2)
K (x2)
I (x4)
bolt-t plate to Base
bolt-t plate to Base I (x4)
T (x1)
D8
Tray
I (x4)
bolt-t plate to Base
Lock Arm to Base
Q (x2)
3mm
3mm
Lock Arm to Base
D (x1) I (x4)
I (x4)
L (x1)
Tray mount to Tray
M6x20
4mm Tray mount to Tray Tray mount to Tray
Clamp/bolt-t upper mount to base
B (x1) C (x1) 4mm
K (x2)
Clamp/bolt-t upper mount to base
H (x1) E (x1)
M (x1)
clamp plate
E (x1)
G (x1) H (x1) E (x1)
clamp plate
6mm
Arm tension adjust
6mm
Wire Cover
Arm tension adjust
T (x1) E (x1) N (x1)
bolt-t plate to Base
E (x1)
G (x1) B (x1) H (x1) C (x1) E (x1)
R (x2) O (x1) S (x2)
3mm
Lock Arm to Base
I (x4)
L (x1)
O (x1) S (x2)
S (x2)
4mm Tray mount to Tray
S (x2)
M (x1)
Clamp/bolt-t upper mount to base
S (x2)
I (x4)
O (x1) S (x2)
H (x1) E (x1)
clamp plate
6mm
N (x1) Arm tension adjust
H (x1) E (x1)
O (x1) S (x2)
Step 1
O (x1) S (x2)
Determine your mounting method. There are two
ways to attach the Swing Laptop Sit/Stand Worksta-
tion to your desktop:
Clamp Method: If you would like to attach the work-
station along the back edge of your desktop, follow
the Clamp Method instructions (Steps 2 - 4).
Bolt-Through Method: If you prefer to attach the
workstation through your desktop, skip Steps 2 - 4
and follow the Bolt-Through Method instructions
(Steps 5 - 7).
Step 2 (Clamp Method)
Align the Upper Clamp with the Base in the orienta-
tion shown and attach it using the four M6x12 Flat-
head Screws and the 4mm Allen wrench.
Step 3 (Clamp Method)
A. Insert the two standoffs of the Lower Clamp
through two of the key slot holes in the back of
the Upper Clamp as shown. There are two pairs of
key slot holes to choose from for different desktop
thicknesses.
• For Desks 0.4" to 1.5" use the top pair of key slot
holes (fig. 1)
• For Desks 1.6" to 3.3" use the bottom pair of key
slot holes (fig. 2)
B. Slide the Lower Clamp assembly down so that the
standoffs are at the bottom of the key slot holes.
J (x4)
A (x1)
M6x12
clamp/bolt-t upper mount to Base
M6x12
J (x4) M8
J (x4)
M8
P (x2)
bolt-t plate to Base
P (x2)
A (x1) B (x1)
M8
bolt-t plate to Base
M8
P (x2)
D8
P (x2)
D8
Q (x2)
bolt-t plate to Base
D (x1)
Q (x2)
clamp/bolt-t upper mount to Base
D8
M6x20
bolt-t plate to Base
D8
Q (x2)
M6x20
K (x2)
Tray mount to Tray
Q (x2)
K (x2)
bolt-t plate to Base
M6x20
D (x1)
Tray mount to Tray
M6x12 M6x20
clamp/bolt-t upper mount to Base K (x2)
J (x4)
T (x1)
Tray Pads F (x1) K (x2) G (x1)
T (x1)
bolt-t plate to Base
bolt-t plate to Base
M8
bolt-t plate to Base
(qty 4) F (x1)
P (x2)
3mm
T (x1)
bolt-t plate to Base
D8
Tray mount to Tray 3mm
bolt-t plate to Base
L (x1)
Allen Wrenches T (x1)
Q (x2)
Lock Arm to Base
L (x1)
F (x1) G (x1) H (x1)
M6x12
M6x20 clamp/bolt-t upper mount to Base
(set of three: 3mm, 4mm, 6mm)
Tray mount to Tray
3mm
K (x2)
J (x4)
Lock Arm to Base 4mm
R (x2)
3mm
L (x1)
bolt-t plate to Base
Flat Wrench
4mm Tray mount to Tray
M (x1)
T (x1)
bolt-t plate to Base
L (x1)
M8
bolt-t plate to Base
M (x1)
Clamp/bolt-t upper mount to base
3mm P (x2)
Lock Arm to Base 4mm Tray mount to Tray
Lock Arm to Base
L (x1)
M6x12 Flathead screw
M6x12
clamp/bolt-t upper mount to Base 6mm 4mm
M (x1)
Clamp/bolt-t upper mount to base
4mm Tray mount to Tray
J (x4) R (x2) O (x1)
(qty 4) D8
M (x1) 6mm clamp plate
Clamp/bolt-t upper mount to base bolt-t plate to Base
N (x1)
Tray mount to Tray M (x1)
Q (x2)
Clamp/bolt-t upper mount to base
N (x1) Arm tension adjust
6mm clamp plate
M6x20 Screw M8
A (x1) B (x1) C (x1)
6mm clamp plate
N (x1) Arm tension adjust bolt-t plate to Base
M6x20
P (x2) Tray mount to Tray
A (x1) B (x1) C (x1)
K (x2) 6mm
(qty 2) clamp plate
N (x1) Arm tension adjust
Arm tension adjust
N (x1)
D8
bolt-t plate to Base
T (x1)
bolt-t plate to Base
Q (x2)
D (x1) I (x4)
M6x20 D (x1) I (x4)
3mm
Tray mount to Tray
Lock Arm to Base
K (x2)
L (x1)
F (x1) G (x1) H (x1) E (x1)
4mm Tray mount to Tray
T (x1)
bolt-t plate to Base F (x1) G (x1) H (x1) E (x1)
M (x1) Clamp/bolt-t upper mount to base
3mm
clamp plate
6mm
Lock Arm to Base
R (x2) O (x1) S (x2)
L (x1)
N (x1) Arm tension adjust
R (x2) O (x1) S (x2)
4mm Tray mount to Tray
M (x1)
Clamp/bolt-t upper mount to base
clamp plate
6mm
N (x1) Arm tension adjust
B (x1) C (x1)
M8
A (x1) B (x1) C (x1)
P (x2)
clamp/bolt-t upper mount to Base
bolt-t plate to Base
D8
C (x1)
Q (x2)
bolt-t plate to Base
M6x20
bolt-t plate to Base
K (x2)
I (x4)
D (x1) I (x4)
Tray mount to Tray T (x1)
bolt-t plate to Base
3mm
I (x4)
L (x1)
Tray mount to Tray
bolt-t plate to Base
H (x1) Parts for E (x1) 4mm
M (x1)
Bolt-through assembly
G (x1) H (x1) E (x1)
Lock Arm to Base
6mm
Upper Base Plate
bolt-t plate to Base
N (x1)
E (x1)
Long Bolt
Tray mount to Tray
O (x1) S (x2)
(qty 2)
Lock Arm to Base
Clamp/bolt-t upper mount to base
R (x2) Lower Base Plate O (x1) S (x2)
(qty 2)
M6x12
clamp/bolt-t upper mount to Base
J (x4)
clamp plate
Tray mount to Tray M6x12
M8 Nuts
clamp/bolt-t upper mount to Base
J (x4)
S (x2)
M8
bolt-t plate to Base
Arm tension adjust
P (x2)
Clamp/bolt-t upper mount to base
(qty 2)
M8
bolt-t plate to Base
P (x2)
D8
D8 Washer
bolt-t plate to Base
Q (x2)
D8
bolt-t plate to Base
M6x20 Q (x2)
clamp plate
Tray mount to Tray (qty 2)
K (x2)
M6x20
Tray mount to Tray
K (x2)
Arm tension adjust
T (x1)
bolt-t plate to Base
T (x1)
bolt-t plate to Base
3mm
Lock Arm to Base
L (x1)
3mm
Lock Arm to Base
L (x1) 4mm Tray mount to Tray
M (x1) Clamp/bolt-t upper mount to base
4mm Tray mount to Tray
M (x1) Clamp/bolt-t upper mount to base
6mm clamp plate
N (x1) Arm tension adjust
6mm clamp plate
N (x1) Arm tension adjust
bolt-t
Q (x2)
bolt-t plate to Base
M6x20
Tray
K (x2)
bolt-t plate to Base
T (x1)
bolt-t
Tray mount to Tray
3mm
Lock
L (x1)
bolt-t plate to Base 4mm Tray
M (x1) Clam
Lock Arm to Base
clam
6mm
N (x1) Arm
Tray mount to Tray
Clamp/bolt-t upper mo
clamp plate
Arm tension adjust
1