Table of Contents
Advertisement
Programming the Keypad
Programming Interface
• All codes are four (4) digits in length .
• Entry code is a four (4) digit code needed to activate the gate .
• Master Code is needed to add, remove or reset entry codes .
• Master Code also functions as the entry code under normal operation .
• Factory default Master Code is 1234 .
• STATUS light should blink and beeper should beep (once) whenever
any button is pressed .
• If more than 10 seconds elapsed between key presses the unit returns
to normal (idle) operating mode .
• Keypad can only enter program mode from sleep mode (keypad is
turned OFF) .
• Keypad will beep three times before going into sleep mode .
Program New Master Code
• Press and release PROGRAM button .
• Enter the old Master Code then press and release PROGRAM button .
• Enter 0, 6 then press and release PROGRAM button
• Enter the new Master Code then press and release PROGRAM button .
• Enter the new Master Code then press and release PROGRAM button
again for confirmation .
• Beeper beeps 3 times to confirm that the new Master Code is
accepted .
NOTE:
If the Master Code is not a matched pair or error occurs, (i .e . if
the entry code is NOT a 4-digit code) the STATUS light will flash rapidly
and the beeper will sound for 2 seconds before returning to normal
operation with old Master Code .
Example:
Key press sequence to change old Master Code from 1 2 3 4
to 3 1 2 1
1 2 3 4
0 6
The round black dot is the 'PROGRAM' button .
Program (Add) New Entry Code
• Press and release PROGRAM button .
• Enter the Master Code then press and release PROGRAM button .
• Enter 0, 2 then press and release PROGRAM button .
NOTE:
If memory is full (all 25 locations are already programmed) the
STATUS light will flash rapidly and the beeper will sound for 2 seconds
before returning to normal operation without saving .
• Enter the new Entry Code then press and release PROGRAM button .
• Beeper beeps 3 times to confirm that the new Entry Code is
accepted .
NOTE:
If the code is NOT 4-digits in length or an error condition has
occurred . The STATUS light will flash rapidly and the beeper will sound
for 2 seconds before returning to normal operation without saving .
Example:
Key press sequence to add '3456' as a new entry code .
(1234 is the Master Code)
1 2 3 4
0 2
The round black dot is the 'PROGRAM' button .
3 1 2 1
3 1 2 1
3 4 5 6
Program (Add) New Temporary
Entry Code
• Press and release PROGRAM button .
• Enter the Master Code then press and release PROGRAM button .
• Enter 8, and any number between 1 thru 7 then press and release
the PROGRAM button . The number 1 thru 7 indicates the number
of days after which the code will be automatically removed from
memory
NOTE:
If memory is full (all 25 locations are already programmed)
or an invalid entry is detected, then an error condition has occurred .
The STATUS light will flash rapidly and the beeper will sound for 2
seconds before returning to normal operation without saving .
• Enter the new Entry Code then press and release PROGRAM
button .
• Beeper beeps 3 times to confirm that the new Entry Code is
accepted .
NOTE:
If the code is NOT 4-digits in length or an error condition
has occurred, the STATUS light will flash rapidly and the beeper will
sound for 2 seconds before returning to normal operation without
saving .
Example:
Key press sequence to add "3456" as a new entry code
that will remain valid for 2-days only . (1234 is the Master Code)
1 2 3 4
8 2
The round black dot is the 'PROGRAM' button .
Example:
Key press sequence to add "3456" as a new entry code
that will remain valid for 7-days only . (1234 is the Master Code)
1 2 3 4
8 7
The round black dot is the 'PROGRAM' button .
Delete An Entry Code
• Press and release PROGRAM button .
• Enter the Master Code then press and release PROGRAM button .
• Enter 0, 3 then press and release PROGRAM button .
• Enter the Entry Code to be deleted then press and release
PROGRAM button .
• Beeper beeps 3 times to confirm that the new Entry Code is
deleted .
NOTE:
If no matching code is found or the code is NOT 4-digit in
length, then an error condition has occurred . The STATUS light will
flash rapidly and the beeper will sound for 2 seconds before returning
to normal operation without saving .
Example:
Key press sequence to delete entry code '3456' from
memory . (1234 is the Master Code)
1 2 3 4
0 3
The round black dot is the 'PROGRAM' button .
11
3 4 5 6
3 4 5 6
3 4 5 6
Advertisement
Table of Contents
