Table of Contents
Advertisement
Quick Links
ACCESS CONTROLS
IMPORTANT:
Allow the
intercom base unit's battery to
charge for 12 hours before using
the system for the first time.
Wireless Gate Entry Intercom
Crystal clear two-way wireless communication up to 500 feet
Thank you for purchasing the Mighty Mule Wireless Gate Entry Intercom.
SAFETY NOTE:
NEVER install the keypad portion
of this system where a person can
reach through the gate to activate it,
or where a person can touch the gate
while activating the keypad.
The recommended minimum distance
between the gate and keypad is 10 ft.
GTO - Gates That Open, LLC • 3121 Hartsfield Road • Tallahassee, Florida 32303
rev - 09-20-10
Base Unit
Installation Instructions
Please read the directions carefully and completely before installing.
Telephone (850) 575-0176 • Fax (850) 575-8912 • www.mightymule.com
Keypad Unit
©2010 GTO - Gates That Open, LLC
Advertisement
Table of Contents
Related Manuals for Mighty Mule Wireless Gate Entry Intercom
Summary of Contents for Mighty Mule Wireless Gate Entry Intercom
-
Page 1: Installation Instructions
Wireless Gate Entry Intercom Installation Instructions Crystal clear two-way wireless communication up to 500 feet Thank you for purchasing the Mighty Mule Wireless Gate Entry Intercom. Please read the directions carefully and completely before installing. SAFETY NOTE: NEVER install the keypad portion... - Page 2 Copyright infringement is a violation of federal law. GTO®, GTO/PRO®, Mighty Mule® are registered trademarks of GTO - Gates That Open, LLC. GTO Access Systems™ is a trademark of GTO - Gates That Open, LLC. These marks are the exclusive property of GTO - Gates That Open, LLC (“GTO”).
-
Page 3: Keypad Description
Keypad Description Keypad Interior Keypad Front CALLING Light: DIP Switches: – 1 2 3 4 5 6 7 8 9 LED is RED when calling and turns Match the keypad dip switch settings with JUMPER GREEN when call is answered. your entry transmitter’s dip switch settings. - Page 4 If your control board doesn’t look like any of these diagrams, please refer to your gate opener installation manual or call GTO Technical Service at 1-800-543-1236 or 850-575-4144. PRO-1000/2000, PRO-SL1000/SL2000 and Old Mighty Mule Mighty Mule 350 Control Board Control Boards...
- Page 5 4. Program the Keypad Programming Interface/Keypad Operation: Add Temporary Entry Code: 1. Press and release PROGRAM button. • In these instructions, the symbol for the Programming 2. Enter the Master Code then press and release PROGRAM Button is: button. • All codes are four (4) digits in length. 3.
-
Page 6: Base Unit Description
Base Unit Description Base Unit Face POWER Light: GREEN: charging; RED: battery power mode (unplugged from transformer); Blinking RED: low battery. KEYPAD BATTERY INDICATOR Light: LED turns ON when keypad battery is low. PUSH TO ANSWER/TALK Button: Use to answer CALL from keypad. PRESS and HOLD to talk; RELEASE to listen. GRANT ACCESS Button: Must be pressed before the person at the keypad can press any key to open the gate. -
Page 7: Test The System
The base unit can be disconnected from the transformer for use in another location. The battery will last approximately four (4) hours when unplugged from the transformer. IMPORTANT: You can turn the base unit OFF to conserve battery power, however it will not receive a signal when OFF. 7. - Page 8 base unit is at least 30 feet. 3. Press the “ID SET” button on the keypad until you hear a beep, then release. This erases all stored ID Codes. 4. Press the “ID SET” button on the MASTER base unit for approximately 2 seconds then release. You will hear ONE beep from the base unit and TWO from the keypad, which means the ID Codes are reassigned.
Need help?
Do you have a question about the Wireless Gate Entry Intercom and is the answer not in the manual?
Questions and answers