Related Manuals for 3M 4295
Summary of Contents for 3M 4295
- Page 1 4295 Pole Mount Cabinet (with Prestubbed Cable) Instructions November 1995 Issue 1, 34-7039-2724-3...
-
Page 2: Table Of Contents
Contents General ............................... 3 Description ............................3 Accessories and Optional Cross Connect Test Probes ............... 4 Cabinet Mounting ..........................5 Splicing............................... 6 Labeling .............................. 6 Jumper Installation ..........................7 Accessories Installation ........................8 Wiring Plans ............................8... -
Page 3: General
1.0 General The 3M™ 4295 Pole Mount Cabinets come loaded with 3M™ 4320 Self-Strip Termination Blocks. The cabinets are also provided with prestubbed cables. All cable attachment, splicing, and bonding within the cabinet is complete. 2.0 Description 24 3/4" (63 cm) Cabinet Size and Pair Count 24 3/4"... -
Page 4: Accessories And Optional Cross Connect Test Probes
Parts Identification Panel Self-Strip Block Assy. Jumper Wireway Component Panel Shield Grounding Block 4295B, 4295C, 4295D 4295E Pole Cabinet Top Pole Mount Bracket Cable Supports, 4295C,D,E Bottom Pole Mount Bracket 3.0 Accessories and Optional Cross-Connect Test Probes 4268 - 800 ft. (243 m), 22 AWG (0.6 mm) violet/white Bell specification jumper wire 4324 Self-Strip Priority Circuit Caps Replacement Self-Strip Caps (100 tan and 100 orange) 4327 Self-Strip Single-Pair Probe with cord... -
Page 5: Cabinet Mounting
4.0 Cabinet Mounting When mounting the cabinet on a pole with a balcony, refer to dimension "A" for correct location of balcony. Pole Cabinet Dimension "A" 4295B 24" (61 cm) 6" (15 cm) Cabinet 4295C 12" (31 cm) 4295D 4" (10 cm) Top Pole Mount Bracket 4295E... -
Page 6: Splicing
When mounting a 3M™ 4295E cabinet, attach additional reinforcing bracket. Reinforcing Bracket Attach cable to pole per your company practice. 5.0 Splicing Splice the cabinet stub(s) to feeder/distribution cables following company practice. Note: The feeder/distribution cable identification table is included in Section 9.0 Wiring Plans. -
Page 7: Jumper Installation
Jumper Installation Make sure wires have clean-cut ends. 1/2" - 3/4" Bend the last 1/2" - 3/4" (13 mm - 19 mm) of wire 90°. (13 mm - 19 mm) 90° Hook Bend Wire Insert wire into port and through the cap until the wire is visible from the exit port. -
Page 8: Accessories Installation
Align pair probe and insert pins in test ports. b. Depress clamps to allow clearance over cap heads. Push probe forward until clamps snap behind cap. 3M™ 4324 SS Priority Circuit Caps 4324 a. Attach 4324 priority caps on special circuits. - Page 9 3M™ 4295C / 900 Pair Cabinet Binder Grp. Multi-Unit Binder Grp. Corresponding Color Color Code Cabinet Pairs White Blue-White 1-25 White Orange-White 26-50 White Green-White 51-75 White Brown-White 76-100 White Slate-White 101-125 White Blue-Red 126-150 White Orange-Red 151-175 White Green-Red...
- Page 10 3M™ 4295D / 1200 Pair Cabinet Binder Grp. Multi-Unit Binder Grp. Corresponding Color Color Code Cabinet Pairs White Blue-White 1-25 White Orange-White 26-50 White Green-White 51-75 White Brown-White 76-100 White Slate-White 101-125 White Blue-Red 126-150 White Orange-Red 151-175 White Green-Red...
- Page 11 3M™ 4295E / 1800 Pair Cabinet Binder Grp. Multi-Unit Binder Grp. Corresponding Color Color Code Cabinet Pairs White Blue-White 1-25 White Orange-White 26-50 1326 White Green-White 51-75 White Brown-White 76-100 White Slate-White 101-125 White Blue-Red 126-150 White Orange-Red 151-175 White...
- Page 12 SUSTAINED OR INCURRED BY REASON OF THE USE OF ANY OF THE SELLER'S PRODUCTS THAT WERE DEFECTIVE. Telecom Systems Division 6801 River Place Blvd. Austin, TX 78726-9000 Printed in USA Printed on 50% recycled paper 800/426-8688 © 3M 1995 34-7039-2724-3 with 10% post-consumer...