Related Manuals for Foxconn J20H086
Summary of Contents for Foxconn J20H086
- Page 1 J20H086 User Manual Technology WLAN Module Approval Sheet Rev. Foxconn Part No. J20H086 Sony Part No. Prepared by Reviewed by Approved by...
-
Page 2: Table Of Contents
CONTENTS REVISION HISTORY ................ 3 PRODUCT OVERVIEW ................ 4 ................ 4 PPLICATION SCOPE MODULE HARDWARE OVERVIEW ..............5 ................5 EATURES ..............5 NTERFACE AND ONNECTOR PCB A .............. -
Page 3: Revision History
1 Revision History Change Description Date Document revision Initial release 2014/05/27... -
Page 4: Product Overview
2 Product Overview The J20H086 802.11a/b/g/n 2X2 and BT4.0+LE module provides wireless modem functionality utilizing direct sequence spread spectrum and OFDM/CCK technology. This module is based on MTK MT7662U solution .It fully complies with IEEE 802.11n,IEEE 802.11 a/b/g, Bluetooth v2.1+EDR, V4.0 standard, offering feature-rich wireless connectivity at high standards, and delivering... -
Page 5: Module Hardware Overview
3 Module Hardware Overview 3.1 Features ♦ IEEE802.11a/b/g/n/ac (2X2) based on MTK MT7662U solution. ♦ Support BT4.0+LE ♦ USB 2.0 Interface, High and Full Speeds supported. ♦ Module is powered by the host with a 3.3V +/- 5% supply. ♦ External PCB printed antennas. ♦... - Page 6 USB_DATA- USB_DATA+ Shield Ground VSYNC Input 3D Video sync Signal Ground Ground DC 3.3V DC 3.3V Ground Ground...
-
Page 7: Pcb Assembly Dimension
3.3 PCB Assembly Dimension Dimension (W x Lx H ): 80mmx25mmx1.0mm PCB: 4 layer FR4 design... -
Page 8: Regulatory
4 Regulatory Industry Canada statement: This device complies with RSS-210 of the Industry Canada Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. - Page 9 être installée de telle sorte qu'une distance de 20cm peut être maintenue entre l'antenne et les utilisateurs. Le produit final doit être étiqueté dans un endroit visible avec l'inscription suivante: "Contient des IC: 2878D- J20H086". Manual Information To the End User The OEM integrator has to be aware not to provide information to the end user regarding how to install or remove this RF module in the user’s manual of the end product which...
- Page 10 minimum distance 20cm between the radiator & your body. This device is intended only for OEM integrators under the following conditions: 1) The antenna must be installed such that 20 cm is maintained between the antenna and users, and 2) The transmitter module may not be co-located with any other transmitter or antenna.
- Page 11 equipment operating in the 2,4 GHz ISM band and using spread spectrum modulation techniques; Harmonized EN covering essential requirements under article 3.2 of the R&TTE Directive EN 301 489‐1 V1.8.1: 2008 Electromagnetic compatibility and Radio Spectrum Matters (ERM); ElectroMagnetic Compatibility (EMC) standard for radio equipment and services; Part 1: Common technical requirements EN 301 489‐17 V2.1.1 2009 Electromagnetic compatibility and Radio spectrum Matters (ERM); ElectroMagnetic Compatibility (EMC) standard for radio equipment and services; Part 17: Specific conditions for 2,4 GHz wideband transmission systems and 5 GHz high performance RLAN equipment National Authorities were informed according to Article 6.4 of Frequency Notification. Special Requirements are considered. The product is labeled with CE Marking. ...
Need help?
Do you have a question about the J20H086 and is the answer not in the manual?
Questions and answers