Electrical Wire Diagram; Replacement Parts - Pit Boss Pro 850-sq Manual

Frequent Flare-Ups Cooking Temperature Attempt cooking at a lower temperature. Grease does have a flash point. Keep the temperature under
176°C / 350°F when cooking highly greasy food.
Grease Build-Up On Follow Care and Maintenance instructions.
Cooking Components
ErP Error Code Unit Not Turned Off Safety feature prevents an automatic restart. Press the Power Button to turn the unit off, wait two
Properly When Last minutes, then press the Power Button to turn the unit on again. Turn to desired temperature. If error
Connected To Power code still displayed, contact Customer Service.
Power Outage While
Unit In Operation
ErH Error Code The Unit Has Press the Power Button to turn the unit off, and allow grill to cool. Follow Care and Maintenance
Overheated, Possibly instructions. After maintenance, remove pellets, and confirm positioning of all component parts. Once
Due To Grease Fire Or cooled, press the Power Button to turn the unit on, then select desired temperature. If error code still
Excess Fuel displayed, contact Customer Service.
ErL Error Code Grill fails to perform Check proper positioning of cooking components. Check hopper for sufficient fuel or if there is an
start-up cycle obstruction in the feed system. Remove pellets and follow Care and Maintenance instructions. Check
grill probe. Confirm if actual temperature is correct and accurate. Follow Care and Maintenance
Grill will not stay lit
instructions if dirty. Check ignitor positioning and that it is heating up properly. In extreme cold, the
grill may require a second start. Turn grill off, wait, then turn on again. Check fan. Ensure it is working
properly. Follow Care and Maintenance instructions if dirty.
Err Error Code with Lack Of Fuel, Poor Fuel Check hopper to check that fuel level is sufficient and replenish if low. Should the quality of wood
PELLET Error Code Quality, Obstruction In pellets be poor, or the length of the pellets too long, this may cause an obstruction in the feed system.
Blinking Feed System, Jammed Remove pellets and follow Care and Maintenance instructions.
Auger
Err Error Code with Ignitor is not working Remove cooking components from the main barrel. Press the Power Button to turn the unit on and
IGNITOR Error Code properly, not making a inspect the igniter. Visually confirm that the igniter is working by placing your hand above the burn
Blinking connection grate and feeling for heat. Visually confirm that the igniter is aligned with the hole in the burn grate,
and open to light the pellets. If not operating properly, call Customer Service for assistance or a
replacement part.
Ignitor failure Igniter needs to be replaced. Contact Customer Service for replacement part.
Err Error Code with Auger not primed Before the unit is used for the first time or anytime the hopper is completely emptied out, the auger
AUGER Error Code must be primed to allow pellets to fill the burn pot. If not primed, the igniter will timeout before the
pellets ignite. Follow Hopper Priming Procedure .
Blinking
Auger motor is jammed, Remove cooking components from the main barrel. Press the Power Button to turn the unit on and
not making connection inspect the auger feed system. Visually confirm that the auger is dropping pellets into the burn pot. If
not operating properly, call Customer Service for assistance or a replacement part.
Err Error Code with Fan is not working Check fan. Ensure it is working properly and air intake is not blocked. Remove hopper access panel
FAN Error Code properly, not making a (see Electric Wire Diagram for diagram), and check for any damage to the fan wires. Follow Care and
Blinking connection Maintenance instructions if fan blades are dirty.
24

ELECTRICAL WIRE DIAGRAM

The Digital Control Board system is an intricate and valuable piece of technology. For protection from power surges and electrical
shorts, consult the wire diagram below to ensure your power source is sufficient for the operation of the unit.
PB – ELECTRIC REQUIREMENTS
220-240V, 50HZ, 250W, 3-PRONG GROUNDED PLUG
NOTE: Electrical components, passed by product safety testing and certification services, comply
with a testing tolerance of ± 5-10 percent.
LOCATE AND REMOVE
THE EIGHT SCREWS
OF ACCESS PANEL ON
UNDERSIDE OF UNIT
FUEL INPUT
RATING:
2.0 KG/H
(4.4 LB/H)
GROUNDED
POWER CORD
VW-1, 105°C/221°F,
18-3 STANDARD CSA
G
GROUND
W
P
IGNITOR ASSEMBLY /
HD CARTRIDGE HEATER
200W, 230V, 2.6 AMP
9.5MM X 127MM (0.375" X 5.000")
INDEX
K : BLACK
W : WHITE
AUGER MOTOR
R : RED
& FEED SYSTEM
Y : YELLOW
230V, 50/60HZ,
P : PURPLE 0.22 AMP, 2 RPM MOTOR
O : ORANGE
G : GREEN
CONTROL BOARD
K K
R
W
GRILL PROBE
W
R
Y
Y
R
DRAFT FAN
230V, 50/60HZ,
0.1 AMP, 1 PHASE
25