Solving Problems; Installing The Gas Cooker - Technika TFS54FC-SGW User Manual

If you have a problem with your appliance, check the table below before calling service. You may be able to avoid
a service call by and avoid unnecessary inconvenience and expense.
For cooking problems, refer to Handling Baking Problems.
Problem Causes
Circuit breaker tripped
Elements won't work
Household fuse blown
120 min Timer now in Manual position
Power not turned on
Oven or grill not working
Control is incorrectly set
Circuit breaker tripped
Power not turned on
Household fuse blown
Oven light not working
Circuit breaker tripped
Lamp blown or loose in socket
Heat escaping through incorrectly
sealed door
Oven not hot enough
Door seal is worn or has moved
Unit smoking when first used Protective oils being removed
Odour on first use of oven Manufacturing oils on elements
120minute timer buzzer not
Timer not wound sufficiently
audible
Oven shelf not inserted corectly, may
Oven shelf tight
be upside down or back to front
Household fuse blown or power
Clock display off
supply is off
NOTE: Only service centers should carry out servicing. Otherwise warranty may be void.

SOLVING PROBLEMS

Remedy
Check circuit breaker
Replace household fuse
Refer to 120 min timer instructions
Switch on electricity
Reset controls
Check circuit breaker
Switch on electricity
Check fuses
Check circuit breaker
Replace or tighten globe
Check shelves or dishes are not
preventing door closing properly.
Check that door is fitted properly after
door removal for cleaning
Replace seal or re set it
This is normal
This is normal
Allow 2-4 hours for odour to dissipate
(open all windows)
Turn timer knob past 15 minute mark.
Then turn to the required number of
minutes.
Remove shelf and insert as per
diagram
Check fuses, power supply
PG 16
Unpacking
Do not fit the burner crowns, burner caps and trivets until after the cooker has been installed.
Locating the cooker
This appliance must be installed by an authorised person in accordance with this instruction manual, AS/NZS 5601
– Gas installations (installation and pipe sizing), local gas fitting regulations, local electrical regulations, local water
regulations, local health regulations, Building Code of Australia and any other government authority.
Overhead clearances—(Measurement A)
Range hoods and exhaust fans shall be installed in accordance with the manufacturer's relevant instructions.
However, in no case shall the clearance between the highest part of the hob of the gas cooking appliance and a
range hood be less than 600 mm or, for an overhead exhaust fan, 750 mm
Side clearances—(Measurements B, & C)
Where B, measured from the periphery of the nearest burner to any vertical combustible
surface, or vertical combustible surface covered with toughened glass or sheet metal, is less
than 200 mm, the surface shall be protected to a height C of not less than 150 mm above
the hob for the full dimension (width or depth) of the cooking surface area. Where the gas
cooking appliance is fitted with a 'splashback', protection of the rear wall is not required.
Additional requirements for freestanding and elevated gas cooking appliances—
(Measurements D & E). Where D, the distance from the periphery of the nearest burner to
a horizontal combustible surface is less than 200 mm, then E shall be 10 mm or more, or the
horizontal surface shall be above the trivet.
Overheat clearances -(Measurement A): The distance between the highest part of the
hob of the gas cooking appliance should be higher than 600mm for a range hood and higher than 750mm for an
overheat exhaust fan.
Installation of the anti-tilt plate
Determine position of cooker and anti-tilt plate.
Securely fix the anti-tilt plate to the floor with appropriate fasteners. Fasten
the stability bolt bracket to the front grame with the 2 screws supplied.
Reposition the cooker back into the anti-tilt plate and then mark the position
of the stability bolt hole. Pull the cooker back out and drill the bolt location
hole. Use a 10mm masonry or wood drill. When drilling into concrete ensure
a minimum hole depth of 30mm. Reposition the cooker back into the anti-tilt
plate, aligning the stability bolt bracked with the 10mm drilled hole. Then slide
the bolt through the bracket and into the hole. Connect Electricity supply/gas
supply but do not turn on until installation is completed.

INSTALLING THE GAS COOKER

PG 17