1. Manuals
  2. Brands
  3. Lanner electronics Manuals
  4. Motherboard
  5. AP-687VF
  6. Manual

Lanner electronics AP-687VF Manual

Single board computer for slot 1 processor
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
AP-687VF/F
Single Board Computer
for Slot 1 Processor
The contents & information in this
manual are subject to change without
prior notice. For reference only.

Advertisement

Table of Contents
loading

Related Manuals for Lanner electronics AP-687VF

Summary of Contents for Lanner electronics AP-687VF

  • Page 1 AP-687VF/F Single Board Computer for Slot 1 Processor The contents & information in this manual are subject to change without prior notice. For reference only.
  • Page 2 Downloaded from StockCheck.com...
  • Page 3 © OPYRIGHT This document is a copyright of the original manufacturer, 1999. The original manufacturer reserves the right to make improvements to the product(s) described in this manual at any time without notice. This manual may not, in whole or in part, be photocopied, reproduced, transcribed, translated, or transmitted in whatever form without the written consent of the manufacturer, except for copies retained by the purchaser for backup purposes.
  • Page 4 Downloaded from StockCheck.com...

  • Page 5: Table Of Contents

    2.2 I NSTALLING AND PGRADING THE 2.3 J UMPER ETTING VERVIEW 2.4 J AP-687VF/F UMPER OCATION FOR 2.5 J AP-687VF/F 9 UMPER ETTINGS UMMARY FOR 2.6 J AP-687VF/F UMPER ETTINGS FOR 2.7 I/O C AP-687VF/F 16 ONNECTORS OCATION FOR 2.8 I/O C...
  • Page 6 ABLE OF ONTENTS CHAPTER 4 RIVERS UPPORT 4.1 D RIVER ISKETTE 4.2 AGP D RIVER TILITIES APPENDIX A H ATCH IMER APPENDIX B T ECHNICAL EFERENCE GLOSSARY TERMS AND CONDITIONS RMA SERVICE REQUEST FORM Downloaded from StockCheck.com...

  • Page 7: Chapter 1 Introduction

    Flash Disk, three DIMMs. Take note that the AP-687VF is a high power & full engine SBC with AGP display of resolution up to 1600x1200 at 256 colors. It is a board that has so much for a deluxe cost.

  • Page 8: Specifications

    Flash Memory Disk : Reserved socket for DiskOnChip from M-System support up to 144 MB Flash memory Disk AGP Controller(AP-687VF) : SIS 6326 AGP chip, on-board 4 MB SGRAM resolution up to 1600x1200 at 256 colors IDE Drive Interface : Two PCI IDE port that support up to four IDE devices...

  • Page 9: Ordering Information

    INTRODUCTION 1.2 O RDERING NFORMATION The AP-687VF/F single board computer are two versions, to order, please check the requirement below: Model No. Description Flash Disk Socket   AP-687VF Single board computer for Pentium II, Pentium Processor with AGP & Flash Disk Socket ...

  • Page 10: Jumper Setting And Connectors

    CHAPTER 2. JUMPER SETTING AND CONNECTORS The figure below shows the jumpers and connectors location on the AP-687VF/F: 2.1 Board Outline of AP-687VF/F VGA1 PMS1 COM1 PKB1 COM2 KCN1 IDE1 IDE2 AP-687VF/F 4 Downloaded from StockCheck.com...

  • Page 11: Installing And Upgrading The Cpu

    CAUTION! Danger of Explosion if battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the manufacturer. Dispose of used batteries according to the battery manufacturer’s instructions. AP-687VF/F 5 Downloaded from StockCheck.com...
  • Page 12 EMOVING THE ATCH LIPPERS 1. With the component side of SBC facing you, push the spring of the latch clipper(s) from right to left for the left latch clipper and vice-versa for right latch clipper. AP-687VF/F 6 Downloaded from StockCheck.com...
  • Page 13 JUMPER SETTINGS AND CONNECTORS 2. Then remove the Celeron Processor by moving upward. AP-687VF/F 7 Downloaded from StockCheck.com...

  • Page 14: Jumper Setting Overview

    A pair of needle-nose pliers is recommended when working with jumpers. If you have any doubts about the best hardware configuration for your application, contact your local sales representative before you make any changes. In general, you simply need a standard cable to make most connections. AP-687VF/F 8 Downloaded from StockCheck.com...

  • Page 15: Jumper Location For Ap-687Vf/F

    JUMPER SETTING AND CONNECTORS 2.4 J AP-687VF/F UMPER OCATION FOR AP-687VF/F 9 Downloaded from StockCheck.com...

  • Page 16: Jumper Settings Summary For Ap-687Vf/F

    JUMPER SETTING AND CONNECTORS 2.5 J AP-687VF/F UMPER ETTINGS UMMARY FOR JUMPER FUNCTION Select AGP Use INTA (AP-687VF Only) JP3~JP7 Select Serial Port#2 Type Select Watch-Dog Time Out Period JP11 Select External CPU Clock JP12 Select Internal CPU Clock Ratio...

  • Page 17: Jumper Settings For Ap-687Vf/F

    JUMPER SETTING AND CONNECTORS 2.6 J AP-687VF/F UMPER ETTINGS FOR JP1 : Select AGP Use INTA (AP-687VF) Default : AGP Use INTA Enabled INTA ( Default ) Disabled INTA Enabled INTA Disable INTA AP-687VF/F 11 Downloaded from StockCheck.com...
  • Page 18 JP3, JP4, JP5, JP6, JP7 : Select Serial Port#2 Type Serial Port#2 Type RS-232 ( Default ) RS-422 RS-485 RS-232 Default : 1 1 1 1 1 1 1 1 1 1 RS-422 3 3 3 3 RS-485 AP-687VF/F 12 Downloaded from StockCheck.com...
  • Page 19 4 sec (Default ) 8 sec 16 sec 32 sec 64 sec 2 3 4 0.5 SEC 1 SEC 2 SEC 1 2 3 4 4 SEC 8 SEC 16 SEC 32 SEC 64 SEC AP-687VF/F 13 Downloaded from StockCheck.com...
  • Page 20 JUMPER SETTING AND CONNECTORS JP11 : Select External CPU Clock Default : JP11 External CPU Clock 66 MHz Auto Detect 66/100 MHz ( Default ) 100 MHz JP11 JP11 66MHz Auto Detect JP11 100MHz AP-687VF/F 14 Downloaded from StockCheck.com...
  • Page 21 4.5 X 5-6,7-8 5.0 X 5.5 X 1-2,3-4,5-6 6.0 X 1-2,3-4 6.5 X 1-2,5-6 7.0 X 7.5 X 3-4,5-6 8.0 X JP12 2.5X JP12 3.0X 3.5X 4.0X 4.5X 5.0X JP12 5.5X 6.0X 6.5X 7.0X 7.5X 8.0X AP-687VF/F 15 Downloaded from StockCheck.com...
  • Page 22 10 sec and CMOS data is cleared. JP14 : Select Flash Disk Address JP14 Flash Disk Address 1-2,7-8 C800~C9FFH 1-2,9-10 CC00~CDFFH 3-4,7-8 D000~D1FFH 3-4,9-10 D400~D5FFH 5-6,7-8 D800~D9FFH 5-6,9-10 DC00~DDFFH JP14 C800~C9FFH JP14 CC00~CDFFH D000~D1FFH D400~D5FFH JP14 D800~D9FFH DC00~DDFFH AP-687VF/F 16 Downloaded from StockCheck.com...
  • Page 23 JUMPER SETTING AND CONNECTORS 2.7 I/O C AP-687VF/F ONNECTOR OCATION FOR VGA1 PMS1 COM1 PKB1 COM2 KCN1 IDE1 IDE2 AP-687VF/F 17 Downloaded from StockCheck.com...

  • Page 24: I/O Connectors Ummary For Ap-687Vf/F

    Primary IDE Cable Connector ( Header ) IDE2 Secondary IDE Cable Connector ( Header ) FDC1 Floppy Cable Connector ( Header ) PRT1 Parallel Cable Connector ( Header ) VGA1 VGA Connector (AP-687VF Only) TMR2 CPU Thermistor Connector AP-687VF/F 18 Downloaded from StockCheck.com...
  • Page 25 J1 : Hard Disk Active LED Connector HDD Active Signal Ground J2 : Reset Switch Reset Signal Speak Signal J3 : External Speaker Connector Ground Power LED V J4 : Power LED & Key Lock Connector Ground Key Lock Signal Ground AP-687VF/F 19 Downloaded from StockCheck.com...

  • Page 26: I/O Connectors Description

    2.10 I/O C ONNECTORS ESCRIPTION FAN1 : CPU FAN Connector PIN NO. DESCRIPTION Ground +12V CPU FAN Status FAN1 FAN1 FAN2 : System Fan Connector PIN NO. DESCRIPTION Ground +12V CPU FAN Status FAN2 FAN2 AP-687VF/F 20 Downloaded from StockCheck.com...
  • Page 27 USB Port#1 V USB Port#1 D0- USB Port#1 D0+ USB Port#1 Ground USB Port#2 V USB Port#2 D1- USB Port#2 D1+ USB Port#2 Ground USBC1 USBC1 IR1 : Alternate IrDa Connector PIN NO. DESCRIPTION IR_RX Ground IR_TX AP-687VF/F 21 Downloaded from StockCheck.com...
  • Page 28 Data Terminal Ready ( DTRA # ) Ground ( GND ) Data Set Ready ( DSRA # ) Request To Send ( RTSA # ) Clear To Send ( CTSA # ) Ring Indicator ( RIA # ) COM1 COM1 AP-687VF/F 22 Downloaded from StockCheck.com...
  • Page 29 SOUTB DTRB # Ground DSRB # RTSB # CTSB # RIB # COM2 COM2 PMS1 : PS/2 Mouse Connector ( Mini Din ) PIN NO. DESCRIPTION PS/2 Mouse Data Ground PS/2 Mouse Clock PMS1 PMS1 AP-687VF/F 23 Downloaded from StockCheck.com...
  • Page 30 JUMPER SETTING AND CONNECTORS PKB1 : PS/2 Keyboard Connector ( Mini Din ) PIN NO. DESCRIPTION PS/2 Keyboard Data Ground PS/2 Keyboard Clock PKB1 PKB1 AP-687VF/F 24 Downloaded from StockCheck.com...
  • Page 31 Data 14 Data 0 Data 15 Ground DMA REQ Ground IOW # Ground IOR # Ground IOCHRDY DMA ACK # Ground Interrupt IOCS16 # HDC CS0 # HDC CS1 # HDD Active # Ground IDE1 IDE1 AP-687VF/F 25 Downloaded from StockCheck.com...
  • Page 32 Data 14 Data 0 Data 15 Ground DMA REQ Ground IOW # Ground IOR # Ground IOCHRDY DMA ACK # Ground Interrupt IOCS16 # HDC CS0 # HDC CS1 # HDD Active Ground IDE2 IDE2 AP-687VF/F 26 Downloaded from StockCheck.com...
  • Page 33 Motor Enable B # Ground Direction # Ground Step # Ground Write Data # Ground Write Gate # Ground Track 0# Ground Write Protect # Read Data # Ground Head Side Select # Disk Change # FDC1 FDC1 AP-687VF/F 27 Downloaded from StockCheck.com...
  • Page 34 Initialize # Data 2 Printer Select IN # Data 3 Ground Data 4 Ground Data 5 Ground Data 6 Ground Data 7 Ground Acknowledge # Ground Busy Ground Paper Empty Ground Printer Select PRT1 PRT1 AP-687VF/F 28 Downloaded from StockCheck.com...
  • Page 35 JUMPER SETTING AND CONNECTORS VGA1 : VGA Connector (AP-687VF/F Only) PIN NO. DESCRIPTION Red Color Signal Green Color Signal Blue Color Signal Ground Ground Ground Ground Ground H-Sync. V-Sync. SPCLK VAG1 VGA1 AP-687VF/F 29 Downloaded from StockCheck.com...
  • Page 36 Downloaded from StockCheck.com...

  • Page 37: Chapter 3 Award Bios Setup

    <Ctrl>, <Alt> and <Delete> keys, or by pushing the ‘ Reset ’ button on the system cabinet. You can also restart by turning the system OFF then ON. AP-687VF/F 29 Downloaded from StockCheck.com...

  • Page 38: Cmos Setup Utility

    : Exit the utility. : Use arrow keys to move cursor to your desired selection. < > <F10> : Saves all changes made to Setup and exits program. : Changes background and foreground colors. <Shift> <F2> AP-687VF/F 30 Downloaded from StockCheck.com...
  • Page 39 Set Time : Hour, Minute and Second. Use 24-hour clock format (for p.m. time, add 12 to the hour number, you would enter 4:30 p.m. as 16:30). When you select the “STANDARD CMOS SETUP” on the main program, the screen display will appears as: AP-687VF/F 31 Downloaded from StockCheck.com...
  • Page 40 • LBA (Logical Block Addressing): During drive accesses, the IDE controller transforms that data address described by sector, head, and cylinder number into a physical block address, significantly improving data transfer rates. For drives that greater 1024 cylinders. AP-687VF/F 32 Downloaded from StockCheck.com...
  • Page 41 5-1/4 inch AT-type high-density drive; 1.2 megabyte capacity 720K, 3.5in 3 1-2 inch double-sided drive; 720 kilobyte capacity 1.44M, 3.5 in 3 1-2 inch double-sided drive; 1.44 megabyte capacity 2.88M, 3.5 in 3 1-2 inch double-sided drive; 2.88 megabyte capacity AP-687VF/F 33 Downloaded from StockCheck.com...
  • Page 42 The system boot will not stop for a disk error ; it will stop for all other Errors. All, But Disk/Key The system boot will not stop for a keyboard or disk error ; it will stop for all other errors. AP-687VF/F 34 Downloaded from StockCheck.com...

  • Page 43: 3.4 Bios Features Setup

    Virus Warning : The default setting of the Virus Warning is “Disabled”. When it is enabled, any attempt to write the boot sector and partition table will halt the system and cause a warning message to appear. If this happens, you can use an anti-virus utility on AP-687VF/F 35 Downloaded from StockCheck.com...
  • Page 44 Gate A20 Option : The default setting is “Fast”. This is the optimal setting for the CPU card. The other option is “Normal”. Typematic Rate Setting : The default setting is “Disabled”. If enabled, you can set the typematic rate and typematic delay. AP-687VF/F 36 Downloaded from StockCheck.com...
  • Page 45 “Disabled”. When enabled, the ROM with the specific address is copied into system DRAM. It will also reduce the size of memory available to the system. After you have made your selection in the BIOS FEATURES SETUP, press the <ESC> key to AP-687VF/F 37 Downloaded from StockCheck.com...

  • Page 46: Chipset Features Setup

    “Disabled” which allows you to change DRAM timing manually. EDO DRAM Speed Selection : The value in this field must correspond to the speed of the DRAM installed in your system. DO NOT change the default setting of this field, as AP-687VF/F 38 Downloaded from StockCheck.com...
  • Page 47 Video BIOS Cacheable : Selecting Enabled allows caching of the video BIOS ROM at C0000h to C7FFFh, resulting in better video performance. However, if any program AP-687VF/F 39 Downloaded from StockCheck.com...
  • Page 48 AWARD BIOS SETUP writes to this memory area, a system eror may result. AP-687VF/F 40 Downloaded from StockCheck.com...
  • Page 49 Spread Spectrum Modulated : When the system clock generator pulses, the extreme values of the pulse generate excess EMI. Enabling pulse spectrum spread modulation changes the extreme values from spikes to flat curves, thus reducing EMI, AP-687VF/F 41 Downloaded from StockCheck.com...
  • Page 50 After you have made your selections in the CHIPSET FEATURES SETUP, press the <ESC> key to go back to the main program screen. AP-687VF/F 42 Downloaded from StockCheck.com...

  • Page 51: Power Management Setup

    User Define : Allows you to customize all power saving timer features. Optimize : This is the recommended setting for general use. Test/Demo : This is for test/demonstration purpose. Disable : Disable the power management features. AP-687VF/F 43 Downloaded from StockCheck.com...
  • Page 52 Full power function will return when a Wake-Up event is detected. HDD Power Down : Options are from “1 Min.” to “15 Min.” and “Disable”. The IDE hard drive will spin down if it is not accessed within a specified length of time. AP-687VF/F 44 Downloaded from StockCheck.com...
  • Page 53 Secondary IDE 0 Secondary IDE 1 Floppy Disk Serial Port Parallel Port After you have made your selection in the POWER MANAGEMENT SETUP, press the <ESC> key to go back to the main program screen. AP-687VF/F 45 Downloaded from StockCheck.com...

  • Page 54: Pnp/Pci Configuration

    : PCI/ISA PnP : Load BIOS Defaults DMA-7 assigned to : PCI/ISA PnP : Load Setup Defaults PNP OS Installed : Select Yes if the system operating environment is Plug-and-Play aware (e.g., Windows 95). AP-687VF/F 46 Downloaded from StockCheck.com...
  • Page 55 D0000H-D3FFFH is occupied by ISA legacy cards, and BIOS will not assign this region for PnP/ISA and PCI cards. Assign IRQ For USB : To use USB feature, set the IRQ to “Enabled”. The default setting is “Enabled”. AP-687VF/F 47 Downloaded from StockCheck.com...

  • Page 56: Load Bios Defaults

    Setup default values. Press the <Y> key and then press the <Enter> key if you want to load the Setup defaults. Press <N> if you do not want to proceed. AP-687VF/F 48 Downloaded from StockCheck.com...
  • Page 57 IDE HDD Block Mode : The Default setting is “Enabled”. This feature enhances the hard disk performance by making multi-sector transfers instead of one sector per transfer. Most IDE drives, except the very early design, have Block Mode transfer feature. AP-687VF/F 49 Downloaded from StockCheck.com...
  • Page 58 They can be assigned as follows: Auto 3F8 / IRQ4 (Serial Port 1 Default) 2F8 / IRQ3 (Serial Port 2 Default) 3E8 / IRQ4 2E8 / IRQ3 Disabled (Disable the onboard serial port) AP-687VF/F 50 Downloaded from StockCheck.com...
  • Page 59 If you have set both supervisor and user password, only the supervisor password allows you to enter the BIOS SETUP PROGRAM. Note : If you forget your password, the only way to solve this problem is to discharge the CMOS memory. AP-687VF/F 51 Downloaded from StockCheck.com...
  • Page 60 CMOS memory and continue with the booting process. 3.15 E ITHOUT AVING Select this option and press the <Enter > key to exit the Setup Utility without recording any new values or changing old ones. AP-687VF/F 52 Downloaded from StockCheck.com...
  • Page 61 CHAPTER 4. DRIVER SUPPORT 4.1 D RIVER ISKETTE The Table list below shows the drivers supported for AP-687VF. Diskette No. Driver Directory Name Genisys CD-ROM No.1 4.2 AGP D RIVER TILITIES This section describes the operation and installation of the software drivers. Below is the Windows 95/98 Driver Installation Procedure –...
  • Page 62 Step 2. Select D:\ Drive, point to folder Ap-686(7)vf and double click. Step 2. Select Vga file under the Ap-686(7)vf window. Step 4. Select and click filename Win9x under Vga window. AP-687VF/F 54 Downloaded from StockCheck.com...
  • Page 63 Step 5. Under the Win9x folder, point to Setup and double click. ® Step 6. The initial setup process of InstallShield Wizard begins by showing SiS display with a setup installation indicator of at the lower right side of the screen. AP-687VF/F 55 Downloaded from StockCheck.com...
  • Page 64 Wizard is completed, a Welcome window is shown on the screen. To continue, press Next tab. Step 8. Click the type of Setup you prefer in the Setup Type window. For normal use, select Typical and press Next tab. AP-687VF/F 56 Downloaded from StockCheck.com...
  • Page 65 Step 9. The Select Program Folder window appears, press Next tab to continue. Otherwise, to change the folder name, type in the desired name in the dialog box on the Program Folders: Step 10. After the program selection is made, press Next tab to start copying files. AP-687VF/F 57 Downloaded from StockCheck.com...
  • Page 66 Step 11. When the setup process of SiS6326 driver is completed, a screen indicating Setup Complete window is shown. Choose Yes dialog to restart your computer and press the Finish tab. AP-687VF/F 58 Downloaded from StockCheck.com...
  • Page 67 For example, if you want to Set 4 seconds for the time-out, you should set JP8: 4L ON C:\DOS> DEBUG -i443 EX.2: For assemble Language Enable : MOV DX, 443H IN AL, DX Disable : IN AL, 43H AP-687VF/F 59 Downloaded from StockCheck.com...
  • Page 68 3C0 - 3CF EGA Card 3D0 - 3DF CGA Card 3E8 - 3EF Serial Port #3 (COM 3) 3F0 - 3F7 Floppy Disk Controller 3F8 - 3FF Serial Port #1 (COM 1) Enable Watch-dog Timer Operation (read) AP-687VF/F 60 Downloaded from StockCheck.com...
  • Page 69 Software redirected to INT 0AH (IRQ 2) IRQ 10 Reserved IRQ 11 Reserved IRQ 12 PS/2 Mouse IRQ 13 Math Coprocessor (CPU Internal) IRQ 14 Primary Hard disk IRQ 15 Secondary Hard Disk Parity Check Error AP-687VF/F 61 Downloaded from StockCheck.com...
  • Page 70 The bus carries instructions back and forth between the CPU and other devices in the system. ISA, EISA, VL-Bus, PCI and SCSI are examples of PC buses. AP-687VF/F 62 Downloaded from StockCheck.com...
  • Page 71 32-bit buses. MCA expansion slots cannot accept 8-bit or 16-bit adapter cards. EISA stands for Extended Industry Standard Architecture, while MCA stands for MicroChannel Architecture. MCA is architecture used in IBM Microcomputer. AP-687VF/F 63 Downloaded from StockCheck.com...
  • Page 72 IEEE802.12 – is a physical layer standard for 100VG AnyLAN. LAN (Local Area Network) – A data communications network spanning a limited area. It provides communications between three or more computers and peripherals, in most cases using a high-speed media as it’s backbone. AP-687VF/F 64 Downloaded from StockCheck.com...
  • Page 73 CPUs. However, when manufacturers introduce any new hardware technology, the software makers need to catch up. At this time of compilation, most applications can’t yet take advantage of MMX capabilities. AP-687VF/F 65 Downloaded from StockCheck.com...
  • Page 74 The most common use for serial port is with a mouse or modem. The reason for this is that a serial port is not a very efficient way to transfer data, so little AP-687VF/F 66 Downloaded from StockCheck.com...
  • Page 75 The Windows OS provides medium text & graphics standard. VL-Bus – It is also known as Local Bus; this is an I/O interface that is directly connected and depended of the system CPU. The VL-Bus is an abbreviation of VESA Local Bus. AP-687VF/F 67 Downloaded from StockCheck.com...
  • Page 76 Terms and Conditions Date:1997.10.20 Warranty Policy 1. All products are warranted against defects in materials and workmanship on a period of two years from the date of purchase by the customer. 2. The buyer will bear the return freight charges for goods that are returned for repair within the warranty period whereas manufacturer will bear the other way after repair.
  • Page 77 RMA Service Request Form Date:1997.10.20 When requesting RMA service, please fill out this “RMA Service Request Form”. This form needs to be shipped with your returns. Service cannot begin until we have this information. Company: Person to contact: Phone No. Purchased Date: Fax No.: Applied Date:...

This manual is also suitable for:

Ap-687f

Table of Contents