DeWalt DW735 Original Instructions Manual page 11

mental abilities; lack of experience, knowledge or skills
unless they are supervised by a person responsible for their
safety. Children should never be left alone with this product.
ASSEMBLY AND ADJUSTMENTS

WARNING: To reduce the risk of serious personal
injury, turn tool off and disconnect tool from power
source before making any adjustments or removing/
installing attachments or accessories. An accidental
start-up can cause injury.

WARNING: Do not remove guards (
injury could result.
Transporting the Planer (Fig. A)

WARNING: For your own safety, it is recommended
that two people carry this machine or serious injury
could result.
When moving your planer, carry it either by the side carrying
handles 2 or by the handles
Bench Mounting (Fig. A)
To facilitate bench mounting, two different sized holes
provided on the four corners of your planer. If mounting the
planer with bolts, use the larger holes. If mounting the planer
with nails or screws, use the smaller holes. It is not necessary to
use both sets of holes.
Always mount your planer firmly to prevent movement. To
enhance the tool's portability, it can be mounted to a piece of
12.7 mm or thicker plywood which can then be clamped to your
work support or moved to other job sites and reclamped.
nOTE: If you elect to mount your planer onto a piece of
plywood, make sure that the mounting screws don't protrude
from the bottom of the wood. The plywood must sit flush on
the work support.

CAUTION: The mounting surface should not be warped or
otherwise uneven.
To Attach the Depth Adjustment Crank
Handle (Fig. C)
1. Remove the screw located in the crank handle shaft.
2. Insert the crank handle
3. Secure in place with the screw and T-wrench
Dust Ejection Ports (Fig. D)
Your planer comes with a dust ejection port. The round
port 9 as shown in Figure. F is for use with a 100 mm dust
collector hose.
To Set Up Dust Ejection (Fig. D)

WARNING: Do not operate your planer without the
dust ejection port locked into place. Do not insert
anything into the dust ejection chute unless the
planer is unplugged and you are clearing a clog or
obstruction in the unit. Do not get your face or eyes
near the dust ejection port when the planer is in
operation. Serious injury could result.
7 , Fig. B). Serious
3 at the base of the planer.
5 over the shaft.
8 provided.

WARNING: Chips are ejected at significant velocity. Keep
hands and face clear of dust ejection port.
1. Select the port
2. Depress the lock button
3. Slide the notches in the dust port over the pins on the chip
ejection chute.
4. Rotate the port until the button engages the dust ejection
chute and locks in place.
To Remove the Dust Ejection Port (Fig. D)
1. Use the T-wrench to depress the lock button
dust chute.
2. Twist the port until the pins are disengaged from the
notches on the port.
3. Pull the dust ejection port off of the dust chute.
Depth Adjustment (Fig. E)
Depth Adjustment Scale (Fig. E)
The depth adjustment scale
your planer, indicates the finished thickness of your workpiece.
One rotation of the depth adjustment crank is equal to 1.6 mm,
are
4
half rotation is equal to 0.8 mm, etc.
Depth Adjustment Crank
Turning the crank clockwise lowers the cutterhead. Turning the
crank counterclockwise raises the cutterhead.
Turret Stop (Fig. F)
Your planer is equipped with a turret stop
multiple boards to the same pre-set depth. Stops are set at
3 mm, 6.5 mm, 12.7 mm, 319 mm, 25.5 mm, and 32 mm.
To Set the Minimum Depth to Which the Carriage
can Travel with the Turret Stop
1. Be sure the carriage is set above 32 mm before trying to set
the turret stop.
2. Turn the dial on the front left of the planer until the desired
thickness setting aligns with the red indicator, then lower
the carriage.
3. Plane the workpiece at desired increments until the correct
final thickness is achieved.
nOTE: Do not use force to crank the carriage below the
level that the turret stop indicates. Permanent damage to
the height adjust ment system on your planer will result.
OPERATION
Instructions for Use

WARNING: Always observe the safety instructions and
applicable regulations.

WARNING: To reduce the risk of serious personal
injury, turn tool off and disconnect tool from power
source before making any adjustments or removing/
installing attachments or accessories. An accidental
start-up can cause injury.
.
9
11 on the chip ejection chute
14 , located on the right front of
17
English
10 .
11 on the
for planing
9