3304030 User’s Manual Packing List Hardware: 3304030 Single Board Computer x 1 Cable Kit: Floppy flat cable x 1 40-pin ATA100 IDE flat cable x 1 DB25 & DB9 cable with bracket x 1 Dual USB cable with bracket x 1...
Page 6
3304030 User’s Manual (This Page is Left for Blank) (This Page is Left for Blank)
Page 7
Chapter1 <Introductions> 1.1 <Product Overview> The 3304030 is an all-in-one single board computer with PISA bus. Based on Intel Mobile solutions with 852GM chipset, it is bundled with Intel Mobile Celeron 1.2GHz processor, DDR266 SDRAM up to 1GB of capacity, Intel Extreme Graphics Technology of onboard VGA display interface, AC97 2-channel audio, USB2.0 interface and one Gigabit Ethernet...
Page 8
3304030 User’s Manual Introduction 1.2 <Product Specification> General Specification Form Factor Half-size PISA CPU card Intel Pentium 4 –M / Mobile Celeron Processor Supports up to 1.2GHz Battery Mode is not supported Intel Speed Step Technology is not supported Memory...
Page 9
3304030 User’s Manual Introduction Ethernet Interface Chipset Intel PRO/1000+ LAN interface with Intel 82540EM Type 10Base-T / 100Base-TX/1000Base-T, auto-switching Fast Ethernet Full duplex, IEEE802.3U compliant Connector External RJ45 connector with LED on rear I/O panel Audio Interface Chipset Intel ICH4 with Realtek ALC201A AC97 3D audio codec...
Page 10
3304030 User’s Manual Introduction 1.3 <Component Placement> 1 x DDR266 DIMM up ICH4 Intel Mobile Celeron to 1GB Processor at 400MHz FSB BIOS Intel 82540EM Intel 852GM Gigabit LAN Compact Flash Socket Audio Codec Component Placement...
Page 11
3304030 User’s Manual Introduction 1.4 <Block Diagram> Intel Mobile Celeron 1.2GHz processor 400MHz FSB 1 x 184-pin DDR266 DIMM Up to 1GB LVDS 852GM UltraATA100 ATAPI Devices PCI B USB2. USB Devices ICH4 Audio AC97 Codec Gigabit Ethernet Controller ISA Bus...
Page 12
3304030 User’s Manual (This Page is Left for Blank) (This Page is Left for Blank)
Page 15
3304030 User’s Manual Hardware Setup 2.3 <Connectors Reference> 2.3.1 <Internal Connectors> Connector Function Remark mPGA479 CPU socket Standard DIMM 184 -pin DDR SDRAM DIMM socket Standard IDE1 40-pin primary IDE connector Standard IDE2 44-pin secondary IDE connector Standard 34-pin floppy connector...
Page 16
Hardware Setup 2.4 <System Setup> 2.4.1 <CPU setup> 3304030 has one 479-pin CPU socket to support Intel Pentium 4 –M / Mobile Celeron processor up to 1.2GHz. Please follow the instruction to install the processor well. CPU Socket 2. Find the p in direction and 1.
Page 17
3304030 User’s Manual Hardware Setup 2.4.2 <Memory Module setup> 3304030 supports one DDR266 SDRAM up to 1GB of capacity, with non-ECC, un-buffered memory supported. DIMM 104-pin 80-pin Please check the pin number to match the socket side well before installing memory module.
Page 18
3304030 User’s Manual Hardware Setup 2.4.3 <CPU cooler setup> There is a cooler attached with the board package, please follow the instructions to install the cooler on the processor. 1. Remove the sticker of the base. 2. Put the base through the fixing hole of the processor and paste on the solder side. Then put the cooler through the base pillar.
Page 19
3304030 User’s Manual Hardware Setup 2.4.4 <Complete the system installation> After installing the CPU, CPU cooler and the memory module, please slot the main board into PISA slot of the backplane carefully. If you connect an ATX power supply with the backplane, you will need to connect an ATX function cable between the main board and the backplane.
Page 20
3304030 User’s Manual Hardware Setup 2.5 <CMOS Setup> The board’s data of CMOS can be setting in BIOS. If the board refuses to boot due to inappropriate CMOS settings, here is how to proceed to clear (reset) the CMOS to its default values.
Page 21
3304030 User’s Manual Hardware Setup 2.6 <Watchdog Timer Setting> The watchdog timer makes the system auto-reset while it stops to work for a period. The integrated watchdog timer can be setup as system reset mode by program. Timeout Value Range...
Page 22
DOM (DiskOnModule) or M-systems DiskOnChip IDE Pro flash disk with or without the additional VCC power cable. The 3304030 also supports Compact Flash Card Type I/II interface. The jumper JCFSEL provides you to setup the CF card on master or slave mode.
Page 23
Hardware Setup 2.8 <Power and Fan Setup> 3304030 has one 4-pin power input connector expect PISA bus powering; it also has two fan connectors. For ATX function, you should connect the ATX connector on the backplane with CN_PS on 3304030.
Page 24
3304030 User’s Manual Hardware Setup 2.9 <Display Interface> 2.9.1 <Analog VG A interface> The board is integrated with Intel 852G GMCH chipset built-in Intel Extreme Graphics Technology with Intel Dynamic Video Memory up to 64MBytes shared with system memory. The CRT / analog VGA interface includes one external DB15 female connector on bracket and one 8 x 2-pin header connector on board.
Page 25
3304030 User’s Manual Hardware Setup 2.9.2 <Digital VG A interface> The board provides one 20 x 2-pin LVDS interface for LCD panel, it supports 18/24-bit single/dual channel up to 1600 x 1200 of resolution. The jumper JVLCD can let you select your panel whether supports +5V or +3.3V of voltage, and the CN_INV provides panel...
Page 27
3304030 User’s Manual Hardware Setup LCD installing guide: Prepare a panel, inverter and 3304030. Inverter LCD panel 870P SBC Please check the datasheet of the panel to see the voltage of the panel, and set the jumper JVLCD to +5V or +3.3V.
Page 28
3304030 User’s Manual Hardware Setup After setup the devices well, you need to select the LCD panel type in the BIOS. The panel type mapping is list below: BIOS panel type selection form For 18-bit color For 24-bit color Output format...
Page 29
Hardware Setup 2.10 < Ethernet Network Interface> The 3304030 is integrated with Intel PRO/1000+ Gigabit Ethernet interface at the type of 10Base-T/100Base-TX/100Base-T auto-switching Ethernet with full duplex and IEEE 802.3U compliant. The 3304030 Ethernet interface is controlled by Intel 82540EM, and it provides the external RJ45 connector on rear I/O panel.
Page 30
3304030 User’s Manual Hardware Setup 2.11 <Audio Interface> 3304030 provides a stereo audio interface with Realtek ALC201A AC97 Codec. The CN_AUDIO provides the interface to use attached audio cable, the CDIN can let you connect audio output from CD-ROM drives.
Page 31
3304030 User’s Manual Hardware Setup 2.12 <GPIO interface> The board offers 8-bit digital I/O to customize its configuration to your control needs. For example, you may configure the digital I/O to control the opening and closing of the cash drawer or to sense the warning signal from a tripped UPS. The following is a detailed description of how the digital I/O is controlled via software programming.
Page 32
3304030 User’s Manual Hardware Setup 2.13 <Switch and Indicator> The JFRNT provides front control panel of the board, such as power button, reset and beeper, etc. Connector: JFRNT Type: onboard 14-pin (2 x 7) 2.54-pitch header Function Signal Signal Function...
Page 33
3304030 User’s Manual Display Mode Setup Chapter 3 <Display Mode Setup> This chapter shows you how to setup the display device under Windows OS. Before you using your display device: 1. Check your software Before you can use the display device properly, please install the VGA driver.
Page 34
3304030 User’s Manual Display Mode Setup For advanced display settings, please click Advanced… button and choose Intel(R) Extreme Graphics. Please click Graphics Properties button to enter the advanced setup. Display Mode Setup...
Page 35
3304030 User’s Manual Display Mode Setup While you entering the Graphics Properties, you will see the options below: This option can let you configure the CRT monitors for Colors, Screen Area (Resolution) and Refresh Rate. This option can let you configure...
Page 36
3304030 User’s Manual Display Mode Setup This option can let you configure the Dual Display for clone mode (same display on two devices) This option can let you configure the Dual Display for Extended Desktop mode Display Mode Setup...
Page 37
3304030 User’s Manual BIOS Setup Chapter 4 <BIOS Setup> The single board computer uses the Award BIOS for the system configuration. The Award BIOS in the single board computer is a customized version of the industrial standard BIOS for IBM PC AT-compatible computers. It supports Intel x86 and compatible CPU architecture based processors and computers.
Page 38
3304030 User’s Manual (This Page is Left for Blank) (This Page is Left for Blank)
3304030 User’s Manual Appendix B Appendix B <Flash BIOS> B.1 BIOS Auto Flash Tool The board is based on Award BIOS and can be updated easily by the BIOS auto flash tool. You can download the tool online at the address below: h ttp://www.award.com...
Page 49
3304030 User’s Manual (This Page is Left for Blank) (This Page is Left for Blank)
Page 50
3304030 User’s Manual Appendix C Appendix C <Watchdog Timer Programming Guide> WDT source from : Wi nBond 83627HF (1) General Description Winbond has a WDT feature inside its chip. We implement its function i nto our circuit . There are many configuration Registors ( CR ) in 83627HF. The...
Page 52
3304030 User’s Manual Appendix C LD8-CRF7- Bit[3..0] : Select IRQ resource for WDT time-out ( Setti ng of 2 selects SMI ) (3) WDT Programmimg guide Step 1 . E nter extended function mode as mentioned as above. Step 2 . Program WDT related CR.
Page 54
3304030 User’s Manual Appendix D Appendix D <Hardware Test> D.1 <Power Consumption> Hardware Intel® Mobile Celeron® 1.2GHz Memory UNIGEN DDR333 512MB x 1 Seagate ST340014A (not counted) CDROM SONY DDU1621 DVD-ROM (not counted) Power Supply SEVENTEAM ST-402HLP Software Windows XP SP1 English Version...
Contact Information Any adviser or comment about our products and service, or anything we can help you please don t hesitate to contact with us. We will do our best service for you. Global American Inc. Address 17 Hampshire Drive Hudson...
Need help?
Do you have a question about the 3304030 and is the answer not in the manual?
Questions and answers