Sleipner SXP35 Installation Manual
Hide thumbs
Also See for SXP35:
- User manual (12 pages) ,
- User manual (12 pages) ,
- Installation manual (28 pages)
Related Manuals for Sleipner SXP35
Summary of Contents for Sleipner SXP35
- Page 1 Installation Guide For Pro DC External Electric Thruster Models SXP35, SXP50 DOCUMENT ID: SLEIPNER AS 5926 REVISION: P.O. Box 519 DATE: N-1612 Fredrikstad 2021 Norway LANGUAGE: www.sleipnergroup.com...
-
Page 2: Table Of Contents
Thruster Measurements ............4 SXP50/140-12V-150MM - SXP50/140 w/Controller and PPC SXP50/140-12V-50MM - SXP50/140 w/Controller and PPC Thruster Specifications............... 5 SXP35/140-12V-50MM - SXP35/140 w/Controller and PPC Technical Specifications ............5 SXP35/140-12V-150MM - SXP35/140 w/Controller and PPC Control Box Technical Specifications ......... 6 Positioning the Stern Thruster ........... -
Page 3: Bow Installation Considerations And Precautions
• If able ensure that stern-drives/ trim-tabs do not interfere with the water flow from the thruster as this can reduce the thrust effectiveness considerably. We recommend the use of our Sleipner cowls to enhance the performance and allow installation in shallow draft boats. Sleipner cowls will also minimise the effect if stern-drives/ trim-tabs obstruct the thruster. -
Page 4: Thruster Measurements
Support bolts diameter Distance of support bolts from tube Distance of support bolts *Valid for SX & SXP * Standard tube (Hull thickness <50mm) * Extended tube for thicker hull models (Hull thickness >50mm to <150mm) MG_0110 SXP35 & SXP50 5926 2021... -
Page 5: Thruster Specifications
- Electronic time-lapse device protects against sudden change of drive direction. - The electric thermal cut-off switch in electro motor protects against overheating (auto-reset when electro motor cools down). - Original Sleipner panels shut off automatically 6 minutes after last use. - Original SLeipner panels use child-safe double ON buttons. -
Page 6: Control Box Technical Specifications
Min ambient temp: -25ºc -25ºc Power supply cable: 35 - 70mm²/ AWG 2 - 00 35 - 70mm²/ AWG 2 - 00 Mount direction : 187 mm 7’36” 170 mm 6’69” 121 mm 4’76” MG_0132 SXP35 & SXP50 5926 2021... -
Page 7: Positioning The Stern Thruster
steering legs or motors Engine Water line Installing the thruster at an angle close to the water line will blast water beyond the water surface. MG_0109 SXP35 & SXP50 5926 2021... -
Page 8: Stern Thruster Cowls/ Grids
243/ 9.6 260/ 10.2 330/ 13 393/ 15.5 515/ 20.3 C (mm/ in) 130/ 5.1 240/ 9.4 D (mm/ i n) 170/ 6.7 256/ 10.1 256/ 10.1 288/ 11.3 340/ 13.4 419/ 16.5 540/ 21.3 MG_0017 SXP35 & SXP50 5926 2021... -
Page 9: Thruster Installation Considerations And Precautions
• If able ensure that stern-drives/ trim-tabs do not interfere with the water flow from the thruster as this can reduce the thrust effectiveness considerably. We recommend the use of our Sleipner cowls to enhance the performance and allow installation in shallow draft boats. Sleipner cowls will also minimise the effect if stern-drives/ trim-tabs obstruct the thruster. -
Page 10: Grids Or Cowls Assembly
1. Attach the cowls or grids with included bolts and washers. (NB: If installion of the cowls ensure the appropriate twist of the cowl to direct water away from obstacles) *Cowl Tighten 2Nm MG_0145 Tighten 2Nm SXP35 & SXP50 5926 2021... -
Page 11: Tunnel Installation
Remove cover guard. Remove cover guard. Align two ends of the tunnel. Remove cover guard. Ensure top lips tabs into the motor inserts. Push two tunnel ends together. Check snap lock positions around the tunnel. MG_0112 SXP35 & SXP50 5926 2021... - Page 12 Compression 50mm ring Spacer Apply MS Polymer sealant or equal to back surface face Hull Compression Drill ring 8.5 / 9 mm 12mm Spacer MG_0262 SXP35 & SXP50 5926 2021...
-
Page 13: Motor Installation
All rings need Maximum hull thickness +10% compression is 50 mm or 150mm Hull thickness Sealant (MS Polymer) Cover the entire surface 7 - 8 All rings need Thruster and attachment bolts +10% compression MG_0113 SXP35 & SXP50 5926 2021... -
Page 14: Propeller Installation
Insert the washer to the end of the shaft spline. Tighten with the propeller lock-nut. Apply anti fouling to the gear leg and propeller. Do not apply anti fouling to any rubber elements of the gear leg or anodes. Drive pin Propeller Washer Anti-fouling Lock nut MG_0054 SXP35 & SXP50 5926 2021... -
Page 15: Control Box Installation
MOTOR CABLE + TORQUE 8Nm BAT. + 5, 6 Nm # SX 50 CONTROL BOX *P- Propositional BAT. - 5, 6 Nm MOTOR CABLE - Control Box hose clamp MOTOR CABLE + TORQUE 8Nm MG_0211 SXP35 & SXP50 5926 2021... -
Page 16: Thruster Electrical Installation
2 Control cables from control panel(s)/ remote Minimum and recommended cable dimensions can be identical due to safety margins and cable heat considerations for short cable lengths. * Minimum or recommended cable cross section in mm2 MG_0126 SXP35 & SXP50 5926 2021... - Page 17 Temp switch NC Tighten to 5, 6 NM 4,13 lb/ft # SX50 CONTROL BOX Thruster Thruster Tighten to Tighten to 5 NM 5 NM 3,69 lb/ft 3,69 lb/ft Temp switch NC & NTC (BLUE HOSE) MG_0319 SXP35 & SXP50 5926 2021...
-
Page 18: Electrical Specifications
Electrical Specifi cations MC_0077 SXP35 & SXP50 5926 2021... -
Page 19: Control Panel Cable Installation
(NB: If two or more control panels are operated at the same time in opposite directions, the electronic control box will stop the thruster until it receives a single signal or thrust in one direction.) • Sleipner on/off equipment it is entirely “plug & play” and require no additional confi guration setup. See the Control panel manual for more information. End Terminator... -
Page 20: S-Link Planning & Precautions
- Round, compact and waterproof plugs with unique keying and colour coding to avoid faulty hookup. - An unlimited number of commands or information transfer on a single cable. - Proprietary Sleipner commands but built 100% on NMEA 2000 standard. Routing the Backbone: Keep routing backbone spur cables to a minimum. -
Page 21: Control Panel Installation
Ø 4.5 mm Ø 4.5 mm Ø 4.5 mm External alarm / buzzer connection (S-link) Supply + 12V / 24V DC Internal fuse / relay External alarm buzzer 12V / 24V DC - max 0,5A MG_0063 SXP35 & SXP50 5926 2021... -
Page 22: Pre-Delivery Checklist
Correct drive direction as per control panel: ..............................The compartment for the thruster has been isolated from general bilge water and has no obvious or suspected risks for flooding: .................................................................................................................................. Other comments by installer: .................................................................................................................................................................... SXP35 & SXP50 5926 2021... -
Page 23: Service And Support
10. This warranty gives you specific legal rights, and you may also have other rights which vary from country to country. Patents MC_0024 At Sleipner we continually reinvest to develop and offer the latest technology in marine advancements. To see the many unique designs we have patented visit our website www.sleipnergroup.com/patents SXP35 & SXP50... - Page 24 © Copyright Sleipner Motor AS, 2021 The information given in the document was correct at the time it was published. However, Sleipner Motor AS can not accept liability for any inaccuracies or omissions it may contain. Continuous product improvement may change the product specifi cations without notice.
Need help?
Do you have a question about the SXP35 and is the answer not in the manual?
Questions and answers