Post Installtion Checklist ............................... 24 Service and Support ................................25 Product Spare Parts and Additional Resources ........................25 Warranty Statement ................................25 Sleipner Motor AS P.O. Box 519, Arne Svendsensgt. 6-8 N-1612 Fredrikstad, Norway MC_0020 SE20 & SE25 & SE30 & SE40 5611 2023...
Sleipner products. The recommendations given in this document are guidelines ONLY, and Sleipner strongly recommends that advice is obtained from a person familiar with the particular vessel and applicable regulations.
7.20 *Valid for SE & SEP Propeller position will vary with each thruster model Single Propeller The gear leg/ propeller(s) must never extend out of the tunnel Tunnel centre line MG_0079 SE20 & SE25 & SE30 & SE40 5611 2023...
40 kg / 88 lbs (10.5V) 2.2 kW / 3hp 10 kg / 22 lbs * SE and SE-IP are measured at motor terminals when the thruster is operated for on/off thrusters SE20 & SE25 & SE30 & SE40 5611 2023...
(NB: This can be overlooked depending on the installation methods defi ned in this manual.) Pivot point important Lowered rotation power performance Stronger rotation power performance Water line Ø min 1/4 Ø (Recommended) min 1/4 Ø (Recommended) MG_0001 SE20 & SE25 & SE30 & SE40 5611 2023...
Increase tunnel length to protect never extend out of the tunnel cavity between the propeller and the propeller from water forces the hull of the boat. when high-speed cruising. MG_0048 SE20 & SE25 & SE30 & SE40 5611 2023...
This can also be an installation method for flat bottomed barges to avoid extremely long tunnels and large oval tunnel openings in the hull. Pos. A Pos. B MG_0004 SE20 & SE25 & SE30 & SE40 5611 2023...
High water force event when the boat is traveling at high speeds it while underway will commonly pound upon the water surface. High water force while underway from wave contact MG_0003 SE20 & SE25 & SE30 & SE40 5611 2023...
This “free” extra thrust in optimal installations be 30 - 40% of the total thrust. (NB: A Sleipner thruster propeller does not produce cavitation at working speed. Therefore, any cavitation and cavitation noise in the tunnel will be caused during improper tunnel installation.)
fi breglass, a resin/ fi breglass mixture must be used in that area.) 8 x layers of fiberglass and resin 8 x layers of fiberglass and resin MG_0005 SE20 & SE25 & SE30 & SE40 5611 2023...
Page 12
You must apply gel coat to areas you have grounded/ moulded to make waterproof. These areas allow water access to the hull which is typically not waterproof without these applications outside. (NB: All original Sleipner tunnels are fully waterproof when delivered except in the areas where you have cut and bonded it to the hull.)
Stern Tunnel Installation MC_0003 For Stern Thruster installation please refer to the supplied manual in your Sleipner product delivery Installation Guide For DC Electric Thruster Models SE80, SE100, SE120, SE130, SE150 Stern Thruster SLEIPNER AS DOCUMENT ID: 222222 REVISION: P.O. Box 519...
SE/SEP/SE IP/SEP IP 30/125S2 SE/SEP/SE IP/SEP IP 40/125S2 SE/SEP/SE IP/SEP IP 30/140S SE/SEP/SE IP/SEP IP 40/140S Stern SE/SEP/SE IP/SEP IP 50/140S SE/SEP/SE IP/SEP IP 60/185S2 STARBOARD Drill centre hole first Smooth surface area MG_0612 SE20 & SE25 & SE30 & SE40 5611 2023...
Page 15
Bolt plate Motor bracket The template must sit on the bracket surface with the bolt plate within the measurement cutout Bolt plate Bolt plate Motor bracket MG_0613 SE20 & SE25 & SE30 & SE40 5611 2023...
Page 16
IMPORTANT Do not apply sealant to the bolt holes. Motor bracket Tunnel Diameter /110mm /125mm Nm lb/ft mm inch Fasten 8,85 13,3 MG_0614 SE20 & SE25 & SE30 & SE40 5611 2023...
Apply anti-fouling to the gear leg and propeller. Do not apply anti-fouling to any rubber elements of the gear leg or anodes. Shaft Spline Propeller Washer Anti-fouling Holding Screw FASTEN MG_0050 19 Nm 14.014 lb/ft SE20 & SE25 & SE30 & SE40 5611 2023...
fits into the slots. Drive Pin > 30° Motor FASTEN (18 Nm) (13.28 lb/ft) coupling Motor support IMPORTANT Do not position support on the motor cap. Propeller MG_0051 SE20 & SE25 & SE30 & SE40 5611 2023...
Wiring Diagram chapter for an overview. Sleipner offers both manual main switches and Automatic Main Switches (AMS). Sleipner AMS is controlled by the control panel in addition to the option of manual operation. Turning on the control panel also turn on the automatic main switch. When the control panel is turned off the automatic main switch is turned off.
The top and bottom wiring diagram is for a dual thruster system, for example a bow and stern installation. 4-wire cable Thruster Fuse 10A ANL Fuse Manual Main Switch BATTERY MG_0590 SE20 & SE25 & SE30 & SE40 5611 2023...
The top and bottom wiring diagram is for a dual thruster system, for example a bow and stern installation. Fuse 10A Automatic Main Switch 5-wire cable Thruster ANL Fuse 4-wire cable BATTERY Fuse 5A MG_0567 SE20 & SE25 & SE30 & SE40 5611 2023...
For Control Panel installation please refer to the Installation Guide accompanying the control panel to be installed. Installation Guide Control Panel SLEIPNER MOTOR AS DOCUMENT ID: REVISION: P.O. Box 519 N-1612 Fredrikstad DATE: Norway www.sleipnergroup.com LANGUAGE: SE20 & SE25 & SE30 & SE40 5611 2023...
The compartment for the thruster has been isolated from general bilge water and has no obvious or suspected risks for flooding: .................................................................................................................................. Other comments by installer: ........................................................................................................................SE20 & SE25 & SE30 & SE40 5611 2023...
11. This warranty gives you specific legal rights, and you may also have other rights which vary from country to country. Patents MC_0024 At Sleipner we continually reinvest to develop and offer the latest technology in marine advancements. To see the many unique designs we have patented visit our website www.sleipnergroup.com/patents SE20 & SE25 & SE30 & SE40...
Need help?
Do you have a question about the SE25 and is the answer not in the manual?
Questions and answers