Product description or drilling, especially during dry operation, generates dust that comes from the material This Husqvarna Drill Motor is a transportable diamond being processed, which frequently contains core drill to be used with an approved drill stand. silica. Silica is a basic component of sand,...
9. LEDs to show power output product when you drill in the ceiling. Use an 10. Electronics box applicable water collector. 11. Assembly plate for Husqvarna drill stand 12. PRCD Note: Other symbols/decals on the product refer to special certification requirements for some markets.
Page 8
General power tool safety warnings • Use personal protective equipment. Always wear eye protection. Protective equipment such as dust mask, non-skid safety shoes, hard hat or hearing WARNING: Read all safety warnings, protection used for appropriate conditions will reduce instructions, illustrations and specifications personal injuries.
Page 9
• Keep cutting tools sharp and clean. Properly • Never perform drilling with the machine secured by maintained cutting tools with sharp cutting edges are the vacuum pad only, except when drilling less likely to bind and are easier to control. downwards.If the vacuum is lost, the pad will release from the workpiece.
Page 10
Always use approved accessories. Speak to your before continuing. dealer for more information. Do not hesitate to contact your Husqvarna dealer if you Personal protective equipment have any more questions about the use of the product. We will willingly be of service and provide you with...
Page 11
Do not use the product if protective plates, protective covers, safety switches or other protective devices WARNING: If the PRCD must be repaired, are not attached or are defective. always speak to an approved Husqvarna service agent. ™ Motor overload protection, Elgard The motor overload protection engages if the motor has 1.
2. Read the operator's manual for the drill stand 1. Download the Husqvarna Fleet Services iOS or carefully and make sure that you understand the Android app Husqvarna Fleet Services.
Page 13
7. Put the slurry ring on the drill spindle (C). Install the ™ Note: Only use the Smartstart function to start a hole. drill bit to the drill spindle (D). (Fig. 16) The power will be very much decreased if it is used 8.
Injuries can Note: Only use diamond drill bits that are approved for occur. your product. Speak to your Husqvarna dealer for more information. 1. To stop the product, set the ON/OFF switch to "0".
There is leakage of gear oil. Sealings are worn out and Speak to an approved Husqvarna must be replaced. service center. There is leakage of water The shaft seals are defect. Speak to an approved Husqvarna from the hole on the water service center.
Technical data Technical data Data DM400 DM430 Motor Electrical motor Single-phase Single-phase Rated voltage, V 100-120, 110, 220-240 100-120, 110, 220-240 Rated power, W 3200 3200 Rated output, W 2300 2300 Rated frequency, Hz 50-60 50-60 Rated current, A 100-120V (US, JP)
Page 18
Data DM400 DM430 Drill diameter in concrete, mm/inch 165-350/ 250-450/ 125-250/ 100-160/ 80-160/ 3-6 55-105/ 2-4 6.5-14 8-18 5-10 Recommended water volume, l/min 1.7-2.4 1.1-1.6 0.9-1.3 2.0-2.5 1.5-2.0 1.2-1.6 Embedded connectivity Note: This part is applicable only for products supplied with embedded connectivity.
Rubber washer, part number 598 72 14-01 * Contact you local service agent for more information Service Approved service center To find your nearest Husqvarna Construction Products approved service center, go to the web site www.husqvarnacp.com. 1188 - 008 - 14.09.2020...
Registered trademarks ® Bluetooth word mark and logos are registered Bluetooth SIG, inc. and any use of trademarks owned by such marks by Husqvarna is under license. 1188 - 008 - 14.09.2020...