Void Venu 210i V2 User Manual
Hide thumbs Also See for Venu 210i V2:

Advertisement

Quick Links

Venu 210i V2
User Guide V1.1

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Venu 210i V2 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Void Venu 210i V2

  • Page 1 Venu 210i V2 User Guide V1.1...
  • Page 2 This user guide is subject to change without notice. For the latest online version, visit: www.voidacoustics.com Void Acoustics and the Void logo are registered trademarks of Void Acoustics Research Ltd. in the United Kingdom, USA and other countries; all other Void trademarks are the property of Void Acoustics...
  • Page 3: Table Of Contents

    Components Factory presets Selecting your presets LED chart Power management Software Changing network settings 6.7.1 Network troubleshooting Processing architecture Internal signal path polarity Mounting Service Return authorisation Shipping and packing considerations Appendix Venu 210i V2 User Guide V1.1 Page 3...
  • Page 4: Safety And Regulations

    Void Acoustics Research Ltd for While every care has been taken in creating this guide, safety is reprocessing. For more information about where you can send...
  • Page 5: Limited Warranty

    Void free and clear of all liens or other specifications for each respective model. Void agrees restrictions.
  • Page 6: Unpacking And Checking

    When you are removing your Venu 210i V2 loudspeaker from its original packaging: • Venu 210i V2 loudspeakers come double boxed and each box is stapled shut; take care when unboxing and removing the staples to avoid injury or damage to the loudspeaker •...
  • Page 7: About

    In buying this product, you are now part of the Void family and we hope using it brings you years of satisfaction. This guide will help you both use this product safely and ensure it performs to its full capability.
  • Page 8: Venu 210I V2 Specifications

    Input equalizer 5 parametric equalizers: hi/lo-shelving, all-pass, band-pass, band-stop, hi/ lo-stop Output equalizer Parametric IIR filters: peaking, hi/lo-shelving, all-pass, band-pass, band-stop, hi/lo-pass Crossover Butterworth, Linkwitz-Riley, Bessel: 6 dB/oct to 48 dB/oct (IIR) Venu 210i V2 User Guide V1.1 Page 8...
  • Page 9: Dimensions

    4 About 4.5 Dimensions Figure 4.1: Dimensions Venu 210i V2 User Guide V1.1 Page 9...
  • Page 10: Cabling And Wiring

    5.3 Venu 210i V2 wiring Input A 10” LF DSP and amplifier Input B 10” LF Out A 2+ N/C 2- N/C Out B 2+ N/C 2- N/C Figure 5.1: Venu 210i V2 wiring diagram Venu 210i V2 User Guide V1.1 Page 10...
  • Page 11: Input Connectors

    5.5 Output connectors Loudspeaker output Neutrik speakON™ CH1+ CH2+ Output B Output A speakON™ speakON™ connector connector CH1- CH2- Figure 5.4: Channel 1 and 2 speakON™ connector diagram. Note: pins 2+/2- are not connected. Venu 210i V2 User Guide V1.1 Page 11...
  • Page 12: Venu 210I Dsp

    11. Neutrik speakON™ output A 5. Preset LEDs 12. Neutrik speakON™ output B 13. PowerCon™ power input 6. Preset select 14. Exhaust vents 7. Ethernet connector 8. Combi Jack - XLR input signal connector input B Venu 210i V2 User Guide V1.1 Page 12...
  • Page 13: Factory Presets

    6 Venu 210i V2 DSP 6.2 Factory presets Factory presets for the Venu 210i V2 are as follows: Preset 1 Air 8 Preset 2 Cyclone 55 Preset 3 Indigo 6S Preset 4 Venu 6 V2 6.3 Selecting your preset To change your Venu 210i V2 preset: 1.
  • Page 14: Power Management

    Preset Select button for at least 3 seconds will toggle the power management. When active (Cyan Status LED), the Venu 210i V2 will enter a low power operating mode after 15 minutes of no input signal (input level below -45 dBu). The DSP board will send a signal to the amplifier module turning off the output stages and enabling standby mode (Blue LED).
  • Page 15: Software

    1. Download and install Armonía Plus from the support page on the Void Acoustics website 2. Connect an ethernet cable from the Venu 210i V2 to the PC or router 3. Open Armonía Plus and click on the cog wheel in the bottom right corner of the window.
  • Page 16: Changing Network Settings

    6 Venu 210i V2 DSP 6.7 Changing network setting Once added to the workspace, double click on the Venu 210i V2 to access the processing options. The Network Settings section is available by clicking on the button under the Scheme window.
  • Page 17: Network Troubleshooting

    Internet Protocol Version 4 (TCP/IPv4), select it and click on Properties. This will allow you to set a static IP address for the PC in the same range as the Venu 210i V2. Figure 6.9: Internet Protocol Version 4 (TCP/IPv$) properties In Armonía Plus, re-enable the network card with the new IP settings in the Communication...
  • Page 18: Processing Architecture

    Processing Processing 170ms POTENTIOMETER Output 3 MONO CLIP Output LIMITER Processing Output 4 clipping Temperature GAIN (5 bands) Input processing OUTPUT EQ/OVER PEAK GAIN DELAY (8-11 bands) LIMITER LIMITER 10ms Output processing Venu 210i V2 User Guide V1.1 Page 18...
  • Page 19: Internal Signal Path Polarity

    This would result in an inefficient use of the power supply’s energy. Figure 6.10: Internal signal path polarity with example input signal. Both channels 1 and 2 are fed with the same sine signal. Venu 210i V2 User Guide V1.1 Page 19...
  • Page 20: Mounting

    Remove all four M6 bolts and remove the cover plate. Figure 7.2: Cover plate removal Step 2: Insert the Heavy Duty Top Hat and replace all four M6 bolts. Figure 7.3: Top hat placement Venu 210i V2 User Guide V1.1 Page 20...
  • Page 21: Service

    Before returning your faulty product for repair, please remember to get an R.A.N. (Return Authorisation Number) from the Void dealer who supplied the system to you. Your dealer will handle the necessary paperwork and repair. Failure to go through this return authorisation procedure could delay the repair of your product.
  • Page 22: Appendix

    101.6 mm (4”) voice coil, wound with copper wire on a high-quality voice coil former for high power handling and long-term reliability. The loudspeaker system shall be a Void Acoustics Venu 210i V2. Venu 210i V2 User Guide V1.1...
  • Page 23 Page intentionally left black...
  • Page 24 North America Void Acoustics North America 503-854-7134 sales.usa@voidacoustics.com Head Office Void Acoustics Research Ltd Unit 15 Dawkins Road Industrial Estate Poole Dorset BH15 4JY England +44 (0) 1202 666 006 info@voidacoustics.com Registered in England & Wales No. 07533536 www.voidacoustics.com...

Table of Contents