Summary of Contents for ICON IP Weider Black WBBE21690.0
Page 1
All manuals and user guides at all-guides.com www.weiderfitness.com USERʼS MANUAL Model No. WBBE2169.0 Serial No. Write the serial number in the space above for future reference. Serial Number Decal (Under Seat) QUESTIONS? If you have questions, or if parts are missing, DO NOT CONTACT THE STORE;...
All manuals and user guides at all-guides.com IMPORTANT PRECAUTIONS WARNING: To reduce the risk of serious injury, read all important precautions and instructions in this manual and all warnings on your inversion system before using your inversion system. ICON assumes no responsibility for personal injury or property damage sustained by or through the use of the inversion system.
All manuals and user guides at all-guides.com BEFORE YOU BEGIN Thank you for selecting the WEIDER BLACK INVER- of this manual. To help us assist you, note the product ® SION SYSTEM. The inversion system will increase model number and serial number before contacting your intervertebral dimension, decrease pressure on us.
All manuals and user guides at all-guides.com PART IDENTIFICATION CHART See the drawings below to identify small parts used in assembly. The number in parentheses by each drawing is the key number of the part, from the PART LIST near the end of this manual. Note: If a part is not in the hard- ware kit, check to see if it has been preassembled.
All manuals and user guides at all-guides.com ASSEMBLY To make assembly easier, carefully read the • For help identifying small parts, use the PART following assembly tips: IDENTIFICATION CHART on page 5. • To hire an authorized service technician to •...
Page 7
All manuals and user guides at all-guides.com 3. Attach the Support Leg (13) to the Center Base (3) with three M10 x 35mm Button Bolts (53) and three M10 Locknuts (65). Attach the Base (14) to the Center Base (3) with four M5 x 25mm Screws (59).
Page 8
All manuals and user guides at all-guides.com 6. See the inset drawing. Identify the Center Frame (7). Apply some of the included grease to both sides of the Left Large Spacer (31). Attach the Left Large Spacer (31) and the Left Frame (4) to the Center Frame (7) with an M10 Locknut (65), an M10 Large Washer (64), and a 29mm Spacer (48).
Page 9
All manuals and user guides at all-guides.com 8. Attach the Top Cover (23) and the Bottom Cover (24) to the Center Frame (7) with two M4 x 15mm Screws (58) and an M4 x 30mm Screw (63). Attach the Center Frame Extension (6) to the Center Frame (7) with two M10 x 53mm Button Bolts (49) and two M10 Locknuts (65).
Page 10
All manuals and user guides at all-guides.com 10. Apply a small amount of grease to an M10 x 95mm Button Bolt (57). Pull the Medium Adjustment Knob (37) outward as far as possible. Insert the bracket on the Backrest Frame (8) into the Top Cover (23). Attach the Backrest Frame (8) to the Center Frame Extension (6) with the M10 x 95mm Button Bolt (57) and an M10 Locknut (65).
Page 11
All manuals and user guides at all-guides.com 12. Slide a Foam Pad (22) onto each side of the Lock Frame (11). Press a Pad Cap (45) into each Foam Pad (22). Pull the indicated Long Adjustment Knob (16) outward, insert the Lock Frame (11) into the Leg Hole Frame (10), and then release the Long Adjustment Knob.
Page 12
All manuals and user guides at all-guides.com 14. Pull the Short Adjustment Knob (73) outward as far as possible, and insert the end of the Leg Frame (10) a few inches into the Backrest Frame (8). See the inset drawing. Press the indicated tab Hole on the Leg Frame Bushing (38), and press the Leg Frame Bushing upward into the Backrest...
Page 13
All manuals and user guides at all-guides.com 16. Attach a Handle (12) to the Left Frame (4) with two M10 x 80mm Button Bolts (52), two M10 Curved Washers (50), and two M10 Locknuts (65). Attach the other Handle (12) in the same way.
All manuals and user guides at all-guides.com ADJUSTMENT This section explains how to adjust the inversion system. See DEVELOPING A PROGRAM on page 17 for important information about how to get the most benefit from the inversion system. Make sure that all parts are properly tightened each time you use the inversion system. Replace any worn parts immediately.
Page 15
All manuals and user guides at all-guides.com ADJUSTING THE LOCK FRAME To secure your ankles in the inversion table, first pull the Long Adjustment Knob (16) outward as far as possible. See the inset drawing. Next, pull the Lock Frame (11) away from the Leg Frame (10).
All manuals and user guides at all-guides.com ROTATING ON THE INVERSION SYSTEM This section explains how to rotate back on the inversion system, and then return to the starting position. Before using the inversion system, see ADJUSTMENT starting on page 14 to correctly set up the inversion sys- tem.
All manuals and user guides at all-guides.com DEVELOPING A PROGRAM This section contains information and suggestions about using the inversion system. Make sure that all parts are properly tightened each time you use the inversion system. Replace any worn parts immediately. See ADJUST- MENT starting on page 14 to identify parts referred to in this section.
All manuals and user guides at all-guides.com PART LIST—Model No. WBBE2169.0 R0909A Key No. Qty. Description Key No. Qty. Description Left Base 63mm Round Cap Right Base Leveling Foot Center Base Foot Left Frame M6 Nut Right Frame 32mm Round Cap Center Frame Extension Pad Cap Center Frame...