Table of Contents
Advertisement
Please note!
If you will not be using the appliance for some time, unplug
from the mains socket:
1. First turn the appliance off by pressing the
(fig. 8);
2. Release the main switch (A22) at the back of the appliance
(fig. 2).
Important!
Never press the main switch while the appliance is on.
6. MENU SETTINGS
6.1 Access the settings menu
1. Press the "
" button (C3) to enter the menu;
2. Scroll through the menu items by pressing
until the required items is displayed;
3. Press the menu item you want to select.
6.2 Exit the menu
When you have made the adjustments, press
until you are back on the homepage.
6.3
Rinse
Use this function to deliver hot water from the coffee spouts
(A9) and hot water spout (D6), if inserted, to clean and heat the
appliance's internal circuit.
1. Place a container with a minimum capacity of 100ml under
the coffee and hot water spouts (fig. 8).
2. A few seconds after the "RINSING" item has been selected,
hot water is delivered first from the coffee spouts and then
from the hot water spout (if inserted) which cleans and
heats the appliance's internal circuit (fig. 7).
3. To stop rinsing, press
stop automatically.
Please note!
•
If the appliance is not used for more than 3-4 days, when
you turn it on again, we strongly recommend performing
2/3 rinses before use;
•
After cleaning, it is normal for the grounds container (A11)
to contain water.
6.4 Descaling
For instructions on descaling, see section "13. Descaling".
6.5 Water filter
For instructions on how to install the filter (D7), see section "15.
Water softener filter".
6.6 Beverages settings
In this section, you can consult your customised settings and, if
you wish, reset the default values for each beverage.
1. Once in the settings menu, press "DRINK SETTINGS". The
2. The values are displayed on vertical bars. The default value
button
3. To go back to the settings menu, press
4. To reset the default values for the beverage displayed,
5. "CONFIRM RESET?": to confirm, press
6. "VALORI FABBRICA""IMPOSTATI": press
The beverage has been reset to the default values. Proceed with
the other beverages or go back to the homepage by pressing
6.7 Auto-off (standby)
Auto-off can be set so that the appliance goes off after 15 or 30
minutes, or 1, 2 or 3 hours.
To programme Auto-off, proceed as follows:
1. Press "AUTO-OFF";
2. Select the required time interval by pressing the selection
3. To confirm, press
Auto-off is now programmed.
6.8
Use this function to enable or disable energy saving. When en-
abled, the function reduces energy consumption in compliance
with European regulations.
or wait for rinsing to
To disable or enable "Energy Saving", proceed as follows:
1. Press "ENERGY SAVING" to disable (
The corresponding symbol (B1) appears on the top bar of the
homepage to indicate that the function has been enabled.
Please note:
If energy saving is active, you may have to wait a few seconds
before delivery.
6.9 Coffee temperature
To change the temperature of the water used to make the cof-
fee, proceed as follows:
1. Press
2. Press the value you want to set (LOW, MEDIUM, HIGH).
Please note:
Varying the temperature has most effect for long beverages.
7
values for the first beverage appear on the display;
is indicated by the
symbol, while the current value is
highlighted by the solid part of the vertical bar;
scroll and display the beverages, press
press
;
cancel, press
twice.
arrows
(increase) or
Energy saving
) the function;
"COFFEE TEMPERATURE"
appear on the display (B1) (the current value is underlined);
;
);
.
(decrease);
.
) or enable (
. The selectable values
. To
(to
Advertisement
Table of Contents
Troubleshooting
