Zeversolar Zeverlution 3680 Quick Installation Manual

Quick k Instal llation Guide
Zeverl lution 36 80/4000 0/5000
532-0 08111-03 3
Mounting DC plu ug
In nverter Wall bracket W
accessory kit t connec ctor
1× 1× 1× 2×
1. U Use a Φ10m mm bit to dr rill 2 holes at a depth of about 70
br racket to th he wall.
2. H Hang the inv verter onto o the wall b bracket slig ghtly downw
3. A Attach the o outer fins o of heat sink k to both sid des of the w
If f additional l grounding g or equipot tential bond ding is requ
Figure e A Figure B F
Danger to lif fe due to hig gh voltages in n the inverte r
Before perfo rming any wo ork on the inve erter, ensure t the DC switch
1. L Loosen the four screw ws of the co over using a a TX25 scre
All manuals and user guides at all-guides.com
www.zev versolar.c om
Sealin ng WiFi a antenna Smart meter r
Docu umentation
plug gs tional） co onnector（optio onal）
（opt
2× 1× 1 1× 1×
×
0mm, inser rt the wall anchors an nd attach th he wall
wards.
wall bracke et using M5 5 screws, a s shown in Figure A.
uired, groun nd the inver rter as show wn in Figur re B.
& AC circuit b breaker are sw witched off and d cannot be re eactivated.
ewdriver an nd remove the cover.
1. Zever rlution is a t transforme erless phot tovoltaic (P
the di irect curren nt of the PV V array into o grid-comp
2. Zever rlution mus st only be o operated by y qualified p
all doc cumentation n relating t to its install lation, com
3. Zever rlution is su uitable for i indoor and outdoor us
4. Zever rlution mus st only be o operated wi ith PV array
applica ation class A. Do not c connect any y sources o
5. PV m odules with h a high cap pacity to gro ound must b
6. When n exposed to o sunlight, t the PV arra ay generate
conduc ctors and th he live com ponents of the inverte
can lea ad to lethal electric sho ocks.
7. All co omponents must rema ain within th eir permitte
8. Zever rlution com plies with t he Low-Vo ltage Direct
Zever rlution also complies w with the req quirements
The in nverter labe els with the e CE mark an nd RCM ma
count tries and reg gions, pleas se visit web bsite (
Icon Exp planation
Gen neral warn ing
- im mportant sa afety inform mation
Haz zardous vo oltage
Hot t surfaces
- Mount t the inverte r in areas w where it can nnot be tou
- Ensure good acce ss to the in nverter for installation
- Ambien nt temperat ture should d be 40°C C to ensure
≤
- Install t the inverte r in an envi ronment w with good ve
- Ensure optimum o operation a nd extend s service life
the inve erter to dire ect sunlight t, rain and s snow.
- The mo ounting met thod, locat ion and sur rface must
inverter r's weight a and dimens sions.
- If moun nted in a res sidential ar rea, we reco ommend m
a solid s surface, pla asterboard d and simila ar materials
recomm mended due e to audible e vibrations s when in us
- Do not put any ob jects on the e inverter. Do not cov
- Mount t the inverte r vertically y or tilted b backward by
- The ele ectrical con nection are ea must poi int downwa
- Observ ve the recom mmended c clearances to walls, o
or obje ects as foll lows to ens sure suffici ent heat dis
below
Direction above
500mm
Recom mmended cle earance 300mm 3
2. AC ca able require ements as f follows:
3. Insert t the condu uctor into t the suitable e
ferrule e acc. to D DIN 46228 and crimp p
the con ntact.
4. Threa ad the AC c cable throu gh the cab le gland. P
diamet ter over 12m mm.
5. Insert t the PE, N a and L condu uctors to th he screw ter
Blade e 1×5.5, torq que: 1.2Nm) . The assign nment is ac
6. Tighte en the swiv vel nut of th he cable gla and by usin
7. Secur re the cove er in the seq quence 1 to 4 (screwd
Danger to life due to high voltages of the PV arra ay
When e exposed to sun nlight, the PV a array generat tes dangerous
compon nents of the in nverter. Touch hing the DC co nductors or th
the DC c connectors fr om the invert er under load , an electric ar
•Do not disconnect th he DC connect tors under loa ad.
•Do not touch non-ins sulated cable e ends.
•Do not touch the DC conductors.
•Do not touch any live e components s of the invert er.
•Have th he inverter mo ounted, install led and comm missioned only
•If an er rror occurs, ha ave it rectified by qualified p persons only.
•Before connecting th he PV array, e nsure that the e DC switch is
1. DC ca able require ements as f follow:
2. Lead the strippe ed cable all the way in to the DC p
Press s the clamp ping bracket t down unt il it audibly
Push th he swivel n nut up to th he thread an nd tighten (
2.0Nm m).
Connec ct the asse mbled DC p plug connec ctors to the
3. For u nused DC c connectors , push dow n the clam
Insert t the sealin g plug into the DC plu g connecto
Finall ly insert the e DC plug c connectors with sealin
2
PV) inverter r with two MPP tracke ers which c
pliant alter nating curr rent, and fe eeds it into
persons wit th the appr ropriate ski lls who hav
mmissioning g, operation n and maint tenance.
se.
ys of prote ection class s II in accord dance with
of energy o other than P PV modules s to the inv
be used if th heir couplin ng capacity does not ex
es dangerou us DC voltag ge which is present in t
er. Touching g the DC con nductors or r the live co
ed operatin ng ranges at t all times.
tive 2014/3 35/EU and t he EMC Dire ective 2014
of safety a nd EMC in A Australia an nd New Zeal
ark. For mor re informat tion about c certificates
www w.zeversol lar.com
).
Icon Explan ation
Time n eed to disc
energy y
WEEE d designation
Observ ve the docu
uched inadv vertently.
n and possi ble service e.
optimal op peration.
entilation.
e by avoidin ng exposing g
be suitable e for the
mounting th he inverter o on
s are not
se.
ver the inve erter.
y max. 15°
ards.
other invert ters,
ssipation.
sides
200mm
Object Description
A External diam meter
B Conductor cro oss-section
C Stripping leng gth of the insu ulated conduct tors
D Stripping leng gth of the oute er sheath of th he AC cable
The PE i nsulated cond ductor must b be 5mm longe er than the L a
lease take out the sea al ring insert t when the
rminal bloc cks and tigh ten them (s screwdriver
cording to t the symbol l on the circ cuit board.
ng a torque of 3.5Nm.
river type: T25,torque e: 2.5Nm).
s DC voltage w which is presen nt in the DC co onductors and
he live compo onents can lea ad to lethal ele ectric shocks.
rc may occur leading to ele ectric shock an nd burns.
y by qualified p persons with t the appropriat te skills.
switched off a and it cannot b be reactivated d.
plug connec ctor.
y snaps into o place.
(SW15, torq que:
e inverter.
ping bracke et and push h the swive l nut up to
or, tighten t the swivel n nut (torque e: 2.0Nm).
ng plugs int to the corre esponding D DC inputs o
converts
the utility g grid.
ve already read
IEC 61730, ,
verter.
xceed 1.0μ F.
the DC
omponents
4/30/EU.
land marke ets.
in other
charge stor red
n
umentation
1
Value
9 mm to 14 mm
4 mm² to 6 mm²
approx. 12 m mm
approx. 70 m mm
and N conducto ors
e cable exte ernal-
r type:
d the live
If you disconn nect
the thread .
on the inver rter.
3