Zeversolar Zeverlution 3680 Quick Installation Manual

Quick k Instal llation Guide
Zeverl lution 36 80/4000 0/5000
532-0 08111-03 3
Mounting DC plu
In nverter Wall bracket W
accessory kit t connec
1× 1× 1× 2×
1. U Use a Φ10m mm bit to dr rill 2 holes at a depth
br racket to th he wall.
2. H Hang the inv verter onto o the wall b bracket slig
3. A Attach the o outer fins o of heat sink k to both sid
If f additional l grounding g or equipot tential bond
Figure e A Figure B F
Danger to lif fe due to hig gh voltages in n the inverte
Before perfo rming any wo ork on the inve erter, ensure t
1. L Loosen the four screw ws of the co over using a
www.zev versolar.c
ug Sealin ng WiFi a antenna Smart meter r
ctor plug gs tional） co onnector（optio onal）
（opt
2× 1× 1 1×
×
of about 70 0mm, inser rt the wall anchors an nd attach th
ghtly downw wards.
des of the w wall bracke et using M5 5 screws, a s shown in
ding is requ uired, groun nd the inver rter as show wn in Figur
r
the DC switch & AC circuit b breaker are sw witched off and d cannot be re
a TX25 scre ewdriver an nd remove the cover.
1. Zever rlution is a t transforme
the di irect curren nt of the PV
2. Zever rlution mus st only be o
all doc cumentation n relating t
3. Zever rlution is su uitable for i
4. Zever rlution mus st only be o
applica ation class A. Do not c
5. PV m odules with h a high cap
6. When n exposed to o sunlight, t
conduc ctors and th he live com
can lea ad to lethal electric sho
7. All co omponents must rema
8. Zever rlution com plies with t
Zever rlution also complies w
The in nverter labe els with the
count tries and reg gions, pleas
Icon Exp planation
Gen neral warn
- im mportant sa
Haz zardous vo
Hot t surfaces
- Mount t the inverte r in areas w
- Ensure good acce ss to the in
- Ambien nt temperat ture should
- Install t the inverte r in an envi
- Ensure optimum o operation a
the inve erter to dire ect sunlight
- The mo ounting met thod, locat
inverter r's weight a and dimens
- If moun nted in a res sidential ar
a solid s surface, pla asterboard
recomm mended due e to audible
- Do not put any ob jects on the
- Mount t the inverte r vertically
- The ele ectrical con nection are
- Observ ve the recom mmended c
or obje ects as foll lows to ens
Direction
Recom mmended cle earance
om
2. AC ca able require ements as f
3. Insert t the condu uctor into t
Docu umentation
ferrule e acc. to D DIN 46228
1× the con ntact.
4. Threa ad the AC c cable throu
diamet ter over 12m mm.
5. Insert t the PE, N a and L condu
he wall
Blade e 1×5.5, torq que: 1.2Nm)
6. Tighte en the swiv vel nut of th
7. Secur re the cove er in the seq
Figure A. Danger to life due to high voltages
re B. When e exposed to sun nlight, the PV a
compon nents of the in nverter. Touch
the DC c connectors fr om the invert
•Do not disconnect th he DC connect
•Do not touch non-ins sulated cable e
•Do not touch the DC conductors.
•Do not touch any live e components
•Have th he inverter mo ounted, install
•If an er rror occurs, ha ave it rectified
•Before connecting th he PV array, e
1. DC ca able require ements as f
2. Lead the strippe ed cable all
Press s the clamp ping bracket
eactivated.
Push th he swivel n nut up to th
2.0Nm m).
Connec ct the asse mbled DC p
3. For u nused DC c connectors
Insert t the sealin g plug into
Finall ly insert the e DC plug c
2
erless phot tovoltaic (P PV) inverter r with two MPP tracke
V array into o grid-comp pliant alter nating curr rent, and fe
operated by y qualified p persons wit th the appr ropriate ski
to its install lation, com mmissioning g, operation n and maint
indoor and outdoor us se.
operated wi ith PV array ys of prote ection class s II in accord
connect any y sources o of energy o other than P PV modules
pacity to gro ound must b be used if th heir couplin ng capacity
the PV arra ay generate es dangerou us DC voltag ge which is
ponents of the inverte er. Touching g the DC con nductors or
ocks.
ain within th eir permitte ed operatin ng ranges at t all times.
he Low-Vo ltage Direct tive 2014/3 35/EU and t
with the req quirements of safety a nd EMC in A Australia an
e CE mark an nd RCM ma ark. For mor re informat tion about c
www w.zeversol lar.com
se visit web bsite ( ).
Icon
ing
afety inform mation
oltage
where it can nnot be tou uched inadv vertently.
nverter for installation n and possi ble service e.
d be 40°C C to ensure optimal op peration.
≤
ronment w with good ve entilation.
nd extend s service life e by avoidin ng exposing g
t, rain and s snow.
ion and sur rface must be suitable e for the
sions.
rea, we reco ommend m mounting th he inverter o on
d and simila ar materials s are not
e vibrations s when in us se.
e inverter. Do not cov ver the inve erter.
y or tilted b backward by y max. 15°
ea must poi int downwa ards.
clearances to walls, o other invert ters,
sure suffici ent heat dis ssipation.
below sides
above
500mm 200mm
3 300mm
follows:
Object Description
A External diam meter
B Conductor cro oss-section
C Stripping leng gth of the insu ulated conduct
D Stripping leng gth of the oute er sheath of th
the suitable e
The PE i nsulated cond ductor must b be 5mm longe
and crimp p
gh the cab le gland. P lease take out the sea al ring insert
uctors to th he screw ter rminal bloc cks and tigh
. The assign nment is ac cording to t the symbol l on the circ
he cable gla and by usin ng a torque of 3.5Nm.
quence 1 to 4 (screwd river type: T25,torque e: 2.5Nm).
of the PV arra ay
array generat tes dangerous s DC voltage w which is presen nt in the DC co
hing the DC co nductors or th he live compo onents can lea ad to lethal ele
er under load , an electric ar rc may occur leading to ele ectric shock an
tors under loa ad.
ends.
s of the invert er.
led and comm missioned only y by qualified p persons with t the appropriat
by qualified p persons only.
nsure that the e DC switch is switched off a and it cannot b be reactivated
follow:
the way in to the DC p plug connec ctor.
t down unt il it audibly y snaps into o place.
he thread an nd tighten ( (SW15, torq que:
plug connec ctors to the e inverter.
, push dow n the clam ping bracke et and push h the swive
the DC plu g connecto or, tighten t the swivel n nut (torque
connectors with sealin ng plugs int to the corre esponding D
ers which c converts
eeds it into the utility g grid.
lls who hav ve already read
tenance.
dance with IEC 61730, ,
s to the inv verter.
does not ex xceed 1.0μ F.
present in t the DC
r the live co omponents
he EMC Dire ective 2014 4/30/EU.
nd New Zeal land marke ets.
certificates in other
Explan ation
Time n eed to disc charge stor red
energy y
WEEE d designation n
Observ ve the docu umentation
1
Value
9 mm to 14 mm
4 mm² to 6 mm²
tors approx. 12 m mm
he AC cable approx. 70 m mm
er than the L a and N conducto ors
t when the e cable exte ernal-
ten them (s screwdriver r type:
cuit board.
onductors and d the live
ectric shocks. If you disconn nect
nd burns.
te skills.
d.
l nut up to the thread .
e: 2.0Nm).
DC inputs o on the inver rter.
3