Note to Installer – • Be sure to leave these instructions with the Consumer. Over the Range Microwave Oven http://www.frigidaire.com Visit our Website at: Note to Consumer – • instructions for future reference. • Skill level – Installation of this appliance requires basic mechanical and electrical skills.
Attach Mounting Plate to Wall ...19 Preparation of Top Cabinet ...19 Check Microwave Assembly ...20 Adapting Microwave Blower for Recirculation ...20, 21 Mount the Microwave Oven ...21, 22 Installing the Charcoal Filter ...22 Before You Use Your Microwave ... 23...
15- to 20- ampere branch circuit single grounded outlet. The outlet box should be located in the cabinet above the microwave oven. The outlet box and supply circuit should be installed by a qualified electrician and conform to the National Electrical...
HOOD EXHAUST NOTE: Read these next two pages only if you plan to vent your exhaust to the outside. If you plan to recirculate the air back into the room, proceed to page 6. OUTSIDE TOP EXHAUST (EXAMPLE ONLY) The following chart describes an example of one possible ductwork installation.
Page 5
Installation Instructions NOTE: If you need to install ducts, note that the total ” x 10” (8.2 x 25.4 cm) rectangular or duct length of 3 ⁄ 6” (15.2 cm) diameter round duct should not exceed 120 equivalent feet (36.5 m). Outside ventilation requires a HOOD EXHAUST DUCT.
Installation Instructions DAMAGE—SHIPMENT/ INSTALLATION • If the unit is damaged in shipment, return the unit to the store in which it was bought for repair or replacement. • If the unit is damaged by the customer, repair or replacement is the responsibility of the customer. •...
Cabinet Needs to 30“ (76.2 cm)wide and free of obstructions. be 30″ (76.2 cm) • or More from the If you are going to vent your microwave oven Cooking Surface to the outside, see Hood Exhaust Section for “ exhaust duct preparation.
The center of any adjacent studs should be 16″ (40.6 cm) or 24″ (61 cm) from this mark. Draw a line down the center of the studs. THE MICROWAVE MUST BE CONNECTED TO AT LEAST ONE WALL STUD.
Your cabinets may have decorative trim that interferes with the microwave installation. Remove the decorative trim to install the microwave properly and to make it level. THE MICROWAVE MUST BE LEVEL. Use a level to make sure the cabinet bottom is level.
It is important to use at least one wood screw mounted firmly in a stud to support the weight of the microwave. Set the mounting plate aside. Drill holes on the circles. If there is a stud, drill a hole for wood screws.
INSTALLATION TYPES This microwave oven is designed for adaptation to the following three types of ventilation: A. Outside Top Exhaust (Vertical Duct) B. Outside Back Exhaust (Horizontal Duct) C. Recirculating (Non-Vented Ductless) OUTSIDE TOP EXHAUST (VERTICAL DUCT) See page 12...
OUTSIDE TOP EXHAUST INSTALLATION OVERVIEW A1. Attach Mounting Plate to Wall A2. Prepare Top Cabinet A3. Check Damper Operation A4. Mount Microwave Oven A5. Adjust Exhaust Adaptor A6. Connect Ductwork ATTACH THE MOUNTING PLATE TO THE WALL Attach the plate to the wall using toggle bolts.
CHECK FOR PROPER DAMPER OPERATION Blower Plate Exhaust Adaptor • Place the microwave in its upright position, with the top of the unit facing up. • Make sure tape securing damper is removed and damper pivots easily before mounting microwave.
OVEN (cont.) Cabinet Front Cabinet Bottom Shelf Self-Aligning Screw Microwave Oven Top 4 Attach the microwave oven to the top cabinet. Insert 2 self-aligning screws through outer top cabinet holes. Turn two full turns on each screw. Tighten the outer two screws to the top of the microwave oven.
Remove tape securing damper. Raise damper flap. Blower Plate Remove and save the screw that holds the blower plate to the microwave. Lift off the blower plate. Blower Plate Slip the damper out of the track on the blower...
Drill the holes, following the instructions on the TOP CABINET TEMPLATE. CAUTION: Wear safety goggles when drilling holes in the cabinet bottom. ADAPTING MICROWAVE BLOWER FOR OUTSIDE BACK EXHAUST 1 Remove and save screw that holds blower motor to microwave.
Page 17
Make sure the wires are not pinched, and that they are properly secured. NOTE: The blower unit exhaust openings should match exhaust openings on rear of microwave oven. Secure the blower unit to the microwave with the original screw. Blower Plate Blower Motor Screw...
Tighten the outer two screws to the top of the slots at back bottom microwave oven. (While tightening screws, hold edge onto four lower the microwave oven in place against the wall and tabs of mounting the top cabinet.) plate.
INSTALLATION OVERVIEW C1. Attach Mounting Plate to Wall C2. Prepare Top Cabinet C3. Check Microwave Assembly C4. Adjust Blower C5. Mount the Microwave Oven C6. Install Charcoal Filter IMPORTANT NOTES: • Make sure the screws for the blower motor and blower plate are securely tightened when they are reinstalled.
(adaptor absent). • If the microwave was shipped for recirculation exhaust, remove the Exhaust Adaptor and proceed to C5. If the microwave was shipped for top exhaust, proceed to C4. ADAPTING MICROWAVE BLOWER FOR RECIRCULATION Remove tape securing damper.
Make sure the wires are not pinched, and that they are properly secured. Secure blower unit to microwave with the screw removed in Step 4. Make sure the screw is tight. Replace blower plate with the screw removed in Step 1.
Tighten the outer two screws to the top of the microwave oven. (While tightening screws, hold the microwave oven in place against the wall and the top cabinet.) Install grease filters. See the Owner’s Manual packed with the microwave.
BEFORE YOU USE YOUR MICROWAVE Make sure the microwave oven has been installed according to instructions. Remove all packing material from the microwave oven. Install turntable and ring in cavity. Replace house fuse or turn breaker back on. Plug power cord into a dedicated 15- to 20-amp electrical outlet.
Need help?
Do you have a question about the FMV157G and is the answer not in the manual?
Questions and answers