Sanuvox SABER MAGNET Instruction Manual

Sanuvox SABER MAGNET Instruction Manual

24v uv coil cleaner

Advertisement

REGISTER
YOUR WARRANTY
ONLINE AT
www.sanuvox.com
READ AND SAVE THESE SAFETY INSTRUCTIONS BEFORE USING THIS PRODUCT.
Read and follow all instructions contained in the manual before using the product. Read the maintenance instructions before opening the UV unit
or system. Failure to comply with these instructions may result in injuries or damage to the UV unit or system.
1.
Installation and servicing of UV units or systems (in an
air conditioning system or not) can be hazardous. Only
trained and qualified service personnel should install,
repair or service equipment.
Untrained personnel can perform basic maintenance
2.
functions such as replacing lamp(s) and/or filter(s). All
other operations should be performed by trained service
personnel.
3.
The unit is not to be used by persons (including children)
with reduced physical, sensory or mental capabilities, or
lack of experience and knowledge.
CAUTION: Unit is not a toy. Keep away from
unsupervised children. Do not leave children unattended
with the unit.
4.
DO NOT hang onto the UV unit or system.
5.
Some UV units or systems could be heavy: Make sure
you have a minimum of 2 people to safely move or install
these UV units or systems, and make sure you adopt the
most ergonomic position possible (use UV unit or system
handles, if applicable).
CAUTION: Installing or maintaining heavy equipment,
especially overhead, can cause back pain or other injuries.
6.
When installing or servicing an overhead UV unit or system,
be careful not to fall off the stepladder. Furthermore, make
sure the UV unit or system latches are always in place to
prevent falling parts.
CAUTION: Some parts of some UV units and systems
may open suddenly if the UV unit or system is installed
high up without its locks.
7.
Units that are obviously damaged must not be operated.
Installation Date: _______________
Installer Contact Info.: _________________________________________
SABER MAGNET 24V
UV COIL CLEANER
Residential Model

IMPORTANT SAFETY INSTRUCTIONS

NEVER EXPOSE EYES OR SKIN TO AN OPERATING UV LAMP.
8.
CAUTION: When working on the UV unit or system,
observe precautions on the literature, tags and labels
attached to the UV unit or system, and all other safety
precautions considered as best practices in the HVAC
industry, if applicable.
9.
When applicable, local regulation may comprise more
restrictive installation and/or certification requirements.
The aforementioned requirements prevail on those of this
document and the installer agree to conform to these at his
own expense.
10. Follow all the safety instructions outlined in this document
and respect all local and national codes applicable.
11. All UV units or systems contain a UV-C source. Damage to
the housing or unintended use of the UV unit or system may
result in harmful UV-C leaks. UV-C may, even in little doses,
cause harm to the eyes and skin.
12. Never expose eyes or skin to an operating UV lamp.
Therefore, before installing or performing maintenance
on the UV unit or system, TURN OFF AND DISCONNECT
the UV unit or system from all power sources (there
may be more than one switch to disconnect) and also
disconnect the HVAC system, is applicable.
CAUTION: Electrical shock may cause injuries or
possibly death. FIRST AID INSTRUCTIONS: If injured,
consult a doctor.
13. UV rays may damage certain types of filters (polymer or
plastic); please keep the UV unit or system light away from
shining directly on plastic.
Sanuvox Technologies Inc, © 2019 All rights reserved. November 2021 EN v.5
14. When installing or performing maintenance on the UV unit
or system, it is recommended to wear safety gloves. In
order to avoid reduced performance of lamp(s), do not
touch lamp glass without gloves.
15. Just like conventional fluorescent lamps, UV lamps contain
a small quantity of mercury: if a lamp breaks, clean and
dispose of with care. UV lamps can be disposed/recycled
after use in the same way as any other fluorescent lamps.
Contact and follow the specific instructions of your local
and national authorities.
16. Use only specified SANUVOX branded replacement
UV lamps for your UV unit or system. Use of any other
lamps will void your warranty and can result in damage to
the UV unit or system.
17. Sanuvox UV units or systems are not waterproof. DO NOT
INSTALL OUTDOORS OR IN WET LOCATION unless
specified otherwise.
18. The use of a UV unit or system is a supplement to and
not a substitute for standard infection control practices;
users must continue to follow all current infection control
practices, including those related to the cleaning and
disinfection of environmental surfaces.
For any inquiries on a UV unit or system, contact :
Installed by: _________________
Instruction Manual
SAVE THESE INSTRUCTIONS
Robert Smith
146 Barr St, Saint-Laurent
Quebec, CA, H4T 1Y4
1-888-726-8869
techsupport@sanuvox.com

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the SABER MAGNET and is the answer not in the manual?

Questions and answers

Summary of Contents for Sanuvox SABER MAGNET

  • Page 1: Important Safety Instructions

    Quebec, CA, H4T 1Y4 high up without its locks. 1-888-726-8869 Units that are obviously damaged must not be operated. techsupport@sanuvox.com Installation Date: _______________ Installed by: _________________ Installer Contact Info.: _________________________________________ Sanuvox Technologies Inc, © 2019 All rights reserved. November 2021 EN v.5...
  • Page 2: Table Of Contents

    Instruction Manual for SABER MAGNET 24V TABLE OF CONTENTS IMPORTANT SAFETY INSTRUCTIONS TABLE OF CONTENTS ABOUT THE PRODUCT COMPONENTS How it Works ACCESSORIES & KITS SETUP & INSTALLATION What you will need What’s included Step by Step Setup & Installation...
  • Page 3: About The Product

    Instruction Manual for SABER MAGNET 24V ABOUT THE PRODUCT The SABER MAGNET 24V coil cleaner prevents and helps reduce mold and other microbial growth on the coil and its surrounding areas. For information or recommendations on how to size your specific application, please call SANUVOX at 1-888-726-8869.
  • Page 4: Setup & Installation

    CAUTION: Handle your product with care to avoid breaking parts. Make sure you have a free and safe space to unpack, install and setup your product. Confirm you have access to the necessary power source for the product requirements (see unit or system label). If you have any questions regarding the installation instructions, call SANUVOX at 1-888-726-8869. What’s included The ballast, 1 UV lamp and a basic installation kit.
  • Page 5 7. And finally, reconnect power to the HVAC unit or system, or plug in the transformer in a power outlet. You are now ready to use your new SABER MAGNET 24V and enjoy great air quality for you and your family. www.sanuvox.com...
  • Page 6: Operation

    How to Operate your Product The SABER MAGNET 24V is an automatic unit: once it’s installed and plugged in, it immediatly turns ON on its own. CAUTION: The suggested operating temperature range is 10 to 66°C (50 to 150°F). Operating the SABER MAGNET 24V outside this range will result in decreased performance.
  • Page 7: Maintenance

    Replacing lamp on the SABER MAGNET 24V is quick and easy. Simply turn off the power source, remove lamp from duct, dispose of old lamp and replace with new Sanuvox branded UV lamp, replace lamp in duct and turn power source back on. See below for detailed step by step instructions.
  • Page 8: Ultraviolets: Uvc

    ULTRAVIOLETS: UVC The UVC (254 nm) wavelengths produced by Sanuvox UV units and systems are the same as the ultraviolets produced by the Sun. The UVC attacks the micro-organisms on a molecular level deactivating the contaminants. Unlike conventional UV lamps on the market, Sanuvox UV units and systems use a patented process designed to deliver the maximum UV dosage to the moving airstream or surface.
  • Page 9: Problems & Solutions Table

    Instruction Manual for SABER MAGNET 24V NOTE: The SABER MAGNET 24V error code is determined by the LED flashing pattern on the ballast. The flashing pattern on the ballast is determined by the number of LED blinks (1 to 5) followed by a 1 second pause. This pattern will repeat over and over until the error code is cleared.
  • Page 10: Warranty

    This warranty applies only to the original purchaser of this product from the original date of purchase. At its option, SANUVOX will repair or replace this product if it is found to be defective in material or workmanship.

This manual is also suitable for:

Bst24g48et

Table of Contents