Related Manuals for Gerima SMA 50 BEV-24.F1
Summary of Contents for Gerima SMA 50 BEV-24.F1
- Page 1 © Operating manual Hand-held beveling machine SMA 50 BEV-24.F1 SMA 50 BEV-14.F1 Operating manual...
- Page 2 All rights, including translation, are reserved. No part of this manual may be reproduced in any form (print, photocopy, microfilm or any other process) without the written permission of GERIMA GmbH, St. Wendel, reproduced or distributed using electronic systems, duplicated or distributed.
-
Page 3: Foreword
If you need to make a guarantee claim, if the machine needs to be repaired or if you need Please contact GERIMA for the latest product in- to order spare parts, please contact our formation. -
Page 4: Table Of Contents
© Contents 1. Foreword • Signs and symbols 2. Technical specification • Technical data • Sipment • Noise emission • Power on time 3. Basic safety instructions 4. Intended use 5. Settings • Replacing carbide inserts • Replacing guiding roll •... -
Page 5: Signs And Symbols
© Signs and symbols Please read the manual before using the ma- The information in this manual are indentified chine ! as follows: Danger! This manual has been created so that you can Warning of person, machinery or work with your device quickly and safely. Here is a environmental damage. -
Page 6: Technical Specification
© Technical specification Technical data SMA 50 BEV-24/14.F1 Dimension and weight Length 600 mm Weight approx. approx. 9,60 Kg Connection value / power Line voltage (SMA 50 BEV-14.F1) 110/120 V / 50 Hz Line voltage (SMA 50 BEV-24.F124) 230 V / 50 Hz Power 2,0 KW Idle speed... -
Page 7: Noise Emission
© Technical manual Noise emission values in accordance with the Power-on time (POT): DIN EN 60745-1 standard: To avoid damaging the machine, it is essential to Vibrations: be monitor how long the machine has been operating continuously (‘power-on time’). Noise emission [dB (A)] Value All electric brushed motors generate large amounts of... -
Page 8: Basic Safety Instructions
• the machine must only be operated in perfect the power supply. working condition and especially the safety de- • Always use genuine GERIMA spare parts and vices must be checked regularly for proper accessories or those that have been approved for function. - Page 9 © Basic safety instructions Before working with or on the Special qualifications are required for the follow- machine, the operator must have ing activities: become acquainted with the • Commissioning: The machine may only be com- machine and must have read and missioned by the manufacturer.
- Page 10 • Faults that could affect the safety of the machine Never lift or carry machine by its power cable. must be remedied immediately. • Always use genuine GERIMA spare parts and accessories. Regular pre-start safety precautions • Check and ensure that all of the Damages caused by wrong power supply! machine’s safety and protective...
- Page 11 Any alterations to the machine must have been ap- • When performing any servicing, maintenance or proved by GERIMA GmbH. repair work de-energize the machine by dis- This also applies to the welding of the component connecting it from the supply and ensure that parts.
-
Page 12: Intended Use
© Basic safety instructions / Intended use Cleaning machine and disposal information: The hand-held beveling machine SMA 50 BEV- 24/14.F1 may only be used for work and materi- All substances and materials used als described in the section ‚intended use‘. must be handled appropriately and accordance with all relevant statutory provisions and legislation. -
Page 13: Settings
© Settings Replacing carbide inserts / guiding roll / milling Setting the bevel length head a leg length = bevel length a Before replacing always disconnect b leg length = bevel length b the machine from the power supply C bevel width by removing the power cable from α... -
Page 14: Operating Mode
© Operating mode General Operation Damages caused by wrong power supply! Two-handed operation Whatever the position of the • Check the supply voltage. It must machine, always use two hands to correspond with the specifications on control the machine! the type plate of the machine. Improper use can cause serious injury: When working with the machine, make sure that the •... -
Page 15: Settings (Radius)
© Settings (radius) Adjusting the radii: Notes on radius milling: Please note that only the position of the upper Choosing the right guiding roll to ensure the correct edge of the radius can be adjusted by rotating the lateral position of the radius is just as important as guiding plate. -
Page 16: Consumables
© Consumables Overview and order numbers carbide inserts for bevel and radii: Aluminium Steel Steel Stainless Function Name of part Copper up to 600 N/ up to 900 N/ Order-nr. steel Brass mm² mm² DX4.B10-V1 0101.404.19-00078 Bevel DX4.B12-V1 0101.404.19-00079 DX4.B15-V1 0101.404.19-00080 0101.404.19-00023 R3-KX8.B20-V1... -
Page 17: Maintenance
Close the opening with The guarantee will be void if re-greasing is carried the covers. out by anyone other than a certified GERIMA service technician. Replenish with about 40 g of Service procedure 4:... -
Page 18: Technical Documentation
© Technical documentation Gear unit SMA 50 BEV-04.F1 0202-26-06-04-00-07 name of part order-nr. Steel sleeve with grooves 0101.482.20-00002 Counter ring 0101.482.20-00003 Round handle with puncture protection 0101.482.19-00025 Guide plate - holder 0101.482.20-00001 Holding plate handle 0101.442.18-00021 Spacer 0101.143.09-00032 Threaded insert M8x15 0101.143.09-00033 Guide plate 0101.143.09-00002... - Page 19 © Technical documentation Gear unit upper part SMA BEV-04.F1 0202-26-06-04-00-07 name of part order-nr. Spacer bevel gear 0101.432.18-00013 Drive shaft, split, top 0101.442.19-00015 Bevel gear (Z=52) 0101.442.19-00016 Bearing housing (upper part) 0101.442.18-00020 Drive unit 2000 W / 230 V / 6.000 rpm 0101.342.18-00018 Drive unit 2000 W / 120 V / 6.000 rpm 0101.342.18-00020...
- Page 20 © Technical documentation Gear unit lower part SMA 50 BEV-04.F1 0202-26-06-04-00-07 name of part order-nr. Cover 0101.442.19-00005 Bearing housing (lower part) 0101.442.19-00004 Drive shaft, split, bottom 0101.442.19-00003 Flywheel with spring magazine 0101.442.19-00002 Threaded insert M6x14 0101.143.09-00023 Snap ring 0000.022.14-00202 Countersunk screw M5x16 0000.022.14-00116 O-ring 12x1 0000.042.19-00001...
- Page 21 © Technical documentation Drive unit SMA 50 BEV-04.F1 name of part order-nr. Motor housing 0101.442.18-00025 Brush holder 220-230V / 50/60Hz 0101.452.18-00028 Brush holder 120V / 60Hz 0101.442.19-00008 Carbon brush set 220-230V / 50/60Hz 0101.453.18-00001 Carbon brush set 120V / 60Hz 0101.442.19-00010 Screw 0101.452.18-00016...
- Page 22 © Technical documentation Drive unit SMA 50 BEV-04.F1 name of part order-nr. Anchor 50/60Hz / 220/230V 0101.442.18-00029 Anchor 60Hz / 120V 0101.442.19-00013 Plate 0101.442.18-00028 Felt ring 0101.452.18-00021 Washer 0101.452.18-00020 Deep groove ball bearing 0101.452.18-00019 Lock washer M4 0101.452.18-00010 Bush 0101.452.18-00025 Deep groove ball bearing 0101.452.18-00026 Screw...
-
Page 23: Guarantee
GERIMA or by one of its authorized specialist retailer or representatives. Guarantee claims can be made only for genuine GERIMA parts and if the machine was used for its intended purpose. The guarantee does not cover, in particular: operational wear and tear; improper use;... -
Page 24: Ec Declaration Of Conformity
SMA 50 BEV-14.F1, 21-299-*****, 00001-99999, 2021 Product SMA 50 BEV-24.F1, 21-296-*****, 00001-99999, 2021 We hereby declare that the above mentioned product complies with all relevant provisions of the Machinery Directive 2006/42/EC. The above product fulfills the relevant requirements of the following guidelines: ►...